AN1953 - Microchip Technology
Section 1.0, General Information Section 2.0, USB Type-C Cables Section 3.0, CC Pins Section 4.0, VCONN Supply Section 5.0, USB Power Delivery 2.0 Section 6.0, Alternate Modes REFERENCES This document is an introduction to USB Type-C™ and is not in tended to be a replacement to the official specification.
Download AN1953 - Microchip Technology
Information
Domain:
Source:
Link to this page:
Documents from same domain
Power Factor Correction in Power Conversion …
ww1.microchip.com© 2007 Microchip Technology Inc. DS01106A-page 2 AN1106 FIGURE 1: CURRENT WAVEFORMS WITH AND WITHOUT PFC These waveforms illustrate that …
2.7V to 5.5V Single Supply CMOS Op Amp
ww1.microchip.comMCP601/1R/2/3/4 DS21314G-page 2 © 2007 Microchip Technology Inc. 1.0 ELECTRICAL CHARACTERISTICS Absolute Maximum Ratings † VDD –VSS.....7.0V
Data Encryption Routines for PIC24 and dsPIC Device
ww1.microchip.com© 2006 Microchip Technology Inc. DS01044A-page 1 AN1044 INTRODUCTION Currently, there are three data encryption standards approved …
Using SAM-BA for Linux on SAMA5D3 Xplained
ww1.microchip.comAN-8995 – Using SAM-BA for Linux on SAMA5D3 Xplained: 42328A−06/2014 Page 5 of 19 2. Setup With Ubuntu distributions, a user has to be member of the dialout group to access serial devices like
MCP6021/1R/2/3/4 - Rail-to-Rail Input/Output, 10 …
ww1.microchip.com2001-2017 Microchip Technology Inc. DS20001685E-page 1 MCP6021/1R/2/3/4 Features • Rail-to-Rail Input/Output • Wide Bandwidth: 10 MHz (typical)
Low Quiescent Current LDO - Microchip Technology
ww1.microchip.com2005-2016 Microchip Technology Inc. DS20001826D-page 1 MCP1700 Features: • 1.6 µA Typical Quiescent Current • Input Operating Voltage Range: 2.3V to 6.0V
MCP1703 250 mA, 16V, Low Quiescent Current
ww1.microchip.com2010 Microchip Technology Inc. DS22049E-page 1 MCP1703 Features: • 2.0 µA Typical Quiescent Current • Input Operating Voltage Range: 2.7V to16.0V
MTCH6102 Low-Power Projected Capacitive Touch …
ww1.microchip.com2014 Microchip Technology Inc. DS40001750A-page 1 Description: Microchip’s MTCH6102 is a turnkey projected capacitive touch controller that simplifies adding
PIC32 GUI Development Board with Projected …
ww1.microchip.comPIC32 GUI Development Board with Projected Capacitance (PCAP) Touch Information Sheet Microchip Technology Inc.
RN4020 Bluetooth Low Energy Module User’s Guide
ww1.microchip.comRN4020 BLUETOOTH LOW ENERGY MODULE USER’S GUIDE 2014 Microchip Technology Inc. DS70005191B-page 7 Preface INTRODUCTION This chapter contains general information that will be useful to know before using the
Related documents
Siemens AG Introduction 0
imc-motors.com0 Introduction motors 1LA, 1LG, 1LL, 1LP, 1MA, 1MJ, 1PP, 1PQ 0/7 Order No. code 0/7 Overview 0/8 Special versions 0/8 Overview 0/13 General technical data 0/13 Overview 0/13 † Cut-away diagram of a low-voltage motor 0/14 † Designs …
The General Linear Model (GLM): A gentle introduction
psych.colorado.edu0 = 19.99 and β 1 = −1.71. Hence, for controls, the value of X in Equation 9.1 is 0, so the predicted nAChR concentration is Yˆ = 19.99−1.71∗0 = 19.99 and for the schizophrenics in the sample, Yˆ = 19.99−1.71∗1 = 18.28 One reason for calling the general …
AN INTRODUCTION TO ERROR CORRECTING CODES Part 1
acsweb.ucsd.eduTYPES OF ECC • Binary Codes – Encoder and decoder works on a bit basis. • Nonbinary Codes – Encoder and decoder works on a byte or symbol basis. – Bytes usually are 8 bits but can be any number of bits. – Galois field arithmetic is used. – Example is a Reed Solomon Code – More generally, we can have codes where the number of symbols is a prime or a power of a prime.
Lecture 1 Introduction - NYU Courant
cims.nyu.edulattice. In this course we will usually consider full-rank lattices as the more general case is not substantially different. Let us see some examples. The lattice generated by (1;0)T and (0;1)T is Z2, the lattice of all integers points (see Figure 2(a)). This basis is not unique: for example, (1;1)T and (2;1)T also generate Z2 (see Figure 2(b)).
1.0 INTRODUCTION TO STRUCTURAL ENGINEERING 1.1 …
www.egr.msu.edu1.0 INTRODUCTION TO STRUCTURAL ENGINEERING 1.1 GENERAL INTRODUCTION Structural design is a systematic and iterative process that involves: 1) Identification of intended use and occupancy of a structure – by owner 2) Development of architectural plans and layout – by architect 3) Identification of structural framework – by engineer
SHIP DESIGN AND CONSTRUCTION (general introduction) …
www.pfri.uniri.hrDESIGN SPEED 13.0 knots, 85% MCR CONSUMPTION 7.5 ton/day, 85% MCR CRUISING RANGE 7200 nm HULL HULL MATERIALS The vessel to be constructed throughout of steel-plates and sections of approved shipbuilding quality, tested and approved by the Classification Society. In general, continuous and scallop welding to be adapted. Intermittent
CHAPTER 1 INTRODUCTION TO FINANCIAL MANAGEMENT
www.uky.eduB- 4 Solutions 8. Income Statement Sales $10,000 OCF = EBIT + D – T Costs 6,350 = 1,550 + 2,100 – 423.50 = $3,226.50 Depreciation 2,100