Analog Discovery ™ Technical Reference Manual
An analog switch (ADG612) allows selecting High Gain versus Low Gain (EN_HG_SC1, EN_LG_SC1) signals from the FPGA. The P and N branches of the differential path are switched together. The ADG612 quad switch was used because it provides excellent impedance and bandwidth parameters: - 1 pC charge injection
Download Analog Discovery ™ Technical Reference Manual
Information
Domain:
Source:
Link to this page:
Documents from same domain
Nexys4 DDR™ FPGA Board Reference Manual - Digilentinc
digilent.comType A USB Host Connector (J5) Serial Prog. Port 2 6-pin JTAG Header (J10) Prog Micro SD Connector (J1) Media Select (JP2) User I/O M2 Mode (JP 1) Programming Mode JP2 JP1 NA SPI Flash NA JTAG USB MicroSD Figure 3. Nexys4 DDR configuration options. Figure 3 shows the different options available for configuring the FPGA. An on-board “mode ...
Basys 3™ FPGA Board Reference Manual - Digilent Reference
digilent.comPIC24 Type A USB Host Connector (J2) Serial Prog. Port 2 6-pin JTAG Header (J5) Prog M2 Mode (JP1) Programming Mode JP1 SPI Flash JTAG USB Figure 3. Basys 3 configuration options. The FPGA configuration data is stored in files called bitstreams that have the .bit file extension. The Vivado
ZedBoard HW Users Guide - Digilent Reference
digilent.comAug 01, 2012 · DDR3 on the PS was routed with 40 ohm trace impedance for single-ended signals, and DCI resistors (VRP/VRN) as well as differential clocks set to 80 ohms. Each DDR3 chip needs its own 240-ohm pull-down on ZQ. DDR-VDDQ is set to 1.5V to support the DDR3 devices selected. DDR-VTT is the termination voltage which is ½ DDR-VDDQ.
Nexys A7 FPGA Board Reference Manual - Digilentinc
digilent.comThe major improvement from the Nexys 4 to the Nexys 4 DDR is the replacement of the 16 MiB Cellular RAM with a 128 MiB DDR2 SDRAM memory. Furthermore, to accommodate the new memory, the pin-out of the FPGA banks changed as well. The audio output (AUD_PWM) needs to be driven open-drain as opposed to push-pull on the Nexys 4. 1 Functional Description
Zybo Z7 Board Reference Manual - Digilentinc
digilent.com• High-bandwidth peripheral controllers: 1G Ethernet, USB 2.0, SDIO • Low-bandwidth peripheral controllers: SPI, UART, CAN, I2C • Programmable from JTAG, Quad-SPI flash, and microSD card • Programmable logic equivalent to Artix-7 FPGA
Arty™ FPGA Board Reference Manual - Digilent Reference
digilent.comport (J10) or it can be derived from a 7 to 15 Volt D power supply that [s connected to Power Jack (J12) or Pin 8 of Header J7. Header J13, located between the power jack and the Ethernet connector, is used to determine which source is used. A power-good LED (LD11), driven by the power good _ (PWRGD) output of the ADP5052 regulator, indicates that
ZYBO - Digilentinc
digilent.comMay 31, 2017 · zybo z7 board digilen t inc. a vailable on z20 v er sion only pibtn401 pibtn402 pibtn403 cobtn4 pibtn404 pibtn501 pibtn502 pibtn503 cobtn5 pibtn504 pid101 pid102 pid103 pid104 pid105 cod1 pid201 pid202 pid203 pid204 pid205 cod2 pid301 pid302 pid303 pid304 pid305 cod3 pid401 pid402 pid403 pid404 pid405 cod4 ...
Analog Discovery 2™ Reference Manual
digilent.comStereo audio amplifier to drive external headphones or speakers with replicated AWG signals 16-channel pattern generator (3.3V CMOS, 100Msample/sec)i ii 16-channel virtual digital I/O including buttons, switches, and LEDs – perfect for logic training applicationsiii iv 16-channel digital logic analyzer (3.3V CMOS,
Digilent Pmod Interface Specification
digilent.comhost controller boards. There are six-pin and twelve-pin versions of the interface defined. The six-pin ... Microcontroller system boards are generally provided with dedicated I 2C connectors and provide pull-up resistors that are jumper selectable to be in or out of circuit. FPGA based system boards generally
Introduction to Digital Design Using Digilent FPGA Boards
digilent.comExample 9 – 7-Segment Decoder 48 Example 10 – 7-Segment Displays: x7seg and x7segb 54 Example 11 – 2's Complement 4-Bit Saturator 64 Example 12 – Full Adder 70 ... digital circuit and implement it by connecting the internal gates in a particular way. This
Related documents
Load Switch Basics - NXP
www.nxp.comLoad Switch Options The many possible applications for load switches let the load-switch manufacturers offer multiple load-switch configurations. A basic load switch such as the NX3P190 from NXP (Figure 3) resembles the circuit in Figure 1 – it has the P-channel MOSFET controlled by a level-shifting and slew-rate control circuit. Figure 3.
LTC7004 (Rev. C)
www.analog.comHigh Voltage, High Side Switch with 100% Duty Cycle n Wide Operating VIN: Up to 60V n 1Ω Pull-Down, 2.2Ω Pull-Up for Fast Turn-On and Turn-Off Times with 35ns Propagation Delays n Internal Charge Pump for 100% Duty Cycle n Adjustable Turn-On Slew Rate n Gate Driver Supply from 3.5V to 15V n Adjustable VIN Overvoltage Lockout
Related search queries
Load switch, Load, Switch, Controlled, Slew, Rate, Slew Rate