APPENDIX B: MATERIAL SETTINGS - Epilog Laser
is very narrow. If the application calls for a black etch, consider using an oxidizer after engraving. Oxidizers are used most commonly if the aluminum has a protective coating (urethane, clear coat, clear anodized) covering the area that is not engraved. Deep metal engraving on aluminum can be done using multiple passes.
Download APPENDIX B: MATERIAL SETTINGS - Epilog Laser
Information
Domain:
Source:
Link to this page:
Documents from same domain
Settings for Success: Techniques for most popular ...
www.epiloglaser.comDepending on the wattage of your laser, the best approach is to set the laser power at 100 percent and adjust the speed to obtain the desired depth. Wood is a very easy material to work with and you can produce very nice detail with as little as 300 DPI engraving. 600 DPI engraving into wood produces even better results.
MINI 18/24 & HELIX - Epilog Laser
www.epiloglaser.comthat turn the laser off if the door is opened during operation, and no special precautions are necessary to operate the high-power laser safely. However, the visible output beam of the Laser Diode Pointer (Red Dot Pointer) is accessible to the operator.
ZING 16 / 24 - Epilog Laser
www.epiloglaser.comThe laser cabinet has safety interlocks that turn the laser off if any access door is opened during operation, and no special precautions are necessary to operate the high-power laser safely. However, the visible output beam of the Laser Diode Pointer (Red Dot Pointer) is …
APPENDIX B: MATERIAL SETTINGS - Epilog Laser
www.epiloglaser.comyour settings by engraving a small square or cutting a small circle. You can fine tune your settings in these areas. • Similar materials use similar settings: When you are working with a material you aren’t familiar with, think about a similar material and what settings you would use with that product.
Section 5: Connecting the Laser to Your Computer
www.epiloglaser.comSection 5: Connecting the Laser to Your Computer 26 The data port connections are on the back of the machine, towards the bottom right. The drawing below shows the location of the data ports on the laser system. USB Port A USB cable is included in the accessory kit. The USB port is located on the right side of the machine, near the rear.
SECTION 3: DRIVER INSTALLATION - Epilog Laser
www.epiloglaser.comWindows 8 and 10: Ethernet Installation SECTION 3: DRIVER INSTALLATION 4. Select Create a new port, then Standard TCP/IP Port. Click Next. 5. Enter the IP Address to match the IP Address you set at the laser in “Setting the IP Address” on page …
Windows 7: Ethernet Installation - Epilog Laser
www.epiloglaser.comWindows 7: Ethernet Installation SECTION 3: DRIVER INSTALLATION 13. Click Next. 14. Click Replace the current driver if requested, then click Next. 15. You can rename your printer here. We have not changed it for this document, but many users like to associate the driver name with the IP Address they are using, for example Epilog Helix 192.168.3.4.
Related documents
CMOS Manufacturing Process
bwrcs.eecs.berkeley.eduEtch and fill trenches Implant well regions Deposit and pattern polysilicon layer Implant source and drain regions and substrate contacts Create contact and via windows Deposit and pattern metal layers. Digital Integrated Circuits Manufacturing Process …
Wet and Dry Etching - University of California, Davis
www.ece.ucdavis.eduetch rate. Silicon dioxide or silicon nitride is usually used as a masking material against HNA. As the reaction takes place, the material is removed laterally at a rate similar to the speed of etching downward. This lateral and downward etching process takes places even with isotropic dry etching which is described in the dry etch section.
Etch rates for micromachining processing-part II ...
www.seas.upenn.eduthe etch rates of other materials that will be exposed to the etch, such as masking films and underlying layers, enables an etch process to be chosen for good selectivity (high ratio of etch rate of the target material to etch rate of the other material)—if one exists. While several large literature-review compilations
Radiofrequency Plasma Sources for Semiconductor Processing
www.seas.ucla.edu1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 Thisisusuallyatalowerfrequency ...
Chapter 1.10 - Miscellaneous Etchants
nanolab.berkeley.eduetch oxide, it is important to remember to dip off any native oxide from the silicon surfaces to be etched in HF solution. Etch rates and temperatures are given below. Complete instructions on the use of EDP are given in Chapter 1.3 of the lab manual. Ethylenediamine N H. 2: