Contents
The OSB substrate complies with Voluntary Product Standard PS2 for wood structural panels and the water-resistive barrier complies as an alternate to the water-resistive barrier prescribed in the code. ZIP System® R-Sheathing is available with a 1/2-inch, 1-inch, 1-1/2-inch and 2-inch foam insulation panel. clearance between ZIP System R. less ...
Download Contents
Information
Domain:
Source:
Link to this page:
Documents from same domain
ZIP System R Sheathing - Huber Engineered Woods
www.huberwood.comZIP System R Sheathing Installation 04 ZIP System ® R Sheathing Installation Manual Step 3. Fasten the panels to the framing members with code approved fasteners. When used to resist lateral
0 ICC ES Report ESR - Huber Engineered Woods
www.huberwood.comICC-ES Evaluation Reports are not to be construed as representing aesthetics or any other attributes not specifically addressed , nor are they to be construed
Installation Instructions - Huber Engineered Woods
www.huberwood.comInstallation Instructions ComposItIon & materIals Huber Engineered Woods (HEW) is committed to the responsible use of natural resources. AdvanTech® panels are produced from young, fast- growing trees for less waste and faster availability.
INSTALLATION
www.huberwood.comsheathing panels are orientedstrand board (OSB), wood structural panels with built-in protective overlays that eliminate the need for building wrap or roofing felt. Install the panels, tape the seams with ZIP System ™ flashing tape, and the building is rough dried-in. When used on a wall, ZIP System ® sheathing functions as a
ADVANTECH® SHEATHING
www.huberwood.comliterature, test reports, installation instructions, and special applications are available through Huber Engineered Woods. Please visit advantechperforms.com or call 800.933.9220 xt E 2716 to speak to a technical representative.
Installation Manual-ZIP System Sheathing-Wall and Roof
www.huberwood.companels in applications where the wall sheathing is designed to resist combined wind uplift and shear. Do not use in fire-rated assemblies in lieu of a ... framing1, light gauge metal framing2, CMU/concrete walls3 and new or existing OSB and plywood sheathing4. 1: Follow installation requirements in ESR-3373 and the remainder of this report. ...
Related documents
Standard Dimensions for Furniture Design
www.cawspi.orgDouglas Fir Hard Maple (Sugar) White Oak White Ash Shortleaf Pine alack Walnut Yellow Poplar alack Cherry Red Oak White Fir Ponderosa Pine White Pine Western Red Cedar Modulus of Elasticity (E) 2 .01 1.95 1.83 1.78 1.77 ... Standard Standing Height: Dimensions of Bookcases and Shelves Bookcase 30" 8" 24" 30" 36" 6" 24" 72" 30" 36" 10" 36" 84 ...
Glulam Product Guide - American Laminators
americanlaminators.comstandard for glulam was Commercial Standard CS253-63, which was published by the ... includes a second set of designations. For example, for an unbalanced 24F layup using visually graded Douglas-fir lumber, the layup designation is identified as a 24F-V4. ... manufactured in commonly used dimensions and cut to length when the beams are ordered ...
Installation Manual
downloads.hearthnhome.com*Weighted average LHV efficiencyusing Douglas Fir dimensional lumber and data collected during EPA emissions test. **Weighted average HHV efficiencyusing Douglas Fir dimensional lumber and data collected during EPA emissions test. ***Efficienciesare based on test results calculated using B415; these calculated efficienciesare then used to
Installation Manual
downloads.hearthnhome.comSTANDARD(s): ASTM E2515, ASTM E2780, UL 1482-2011 (2015), ULC-S627-00, CSA B415.1 Fire Risk. Hearth & Home Technologies disclaims any responsibility for, and the warranty will be voided by, the following actions:! WARNING • Installation and use of any damaged appliance. • Modification of the appliance.
CROSS-LAMINATED TIMBER - BRE
www.bre.co.ukfir, silver fir, Douglas fir, pine or other timbers. While C24-grade timber is often used, there has been an increase in the use of C16 timber. As the latter is more readily available in the UK, manufacture of CLT panels may become more feasible in future; at the time of writing, all panels are imported (eg from Germany, Austria and Switzerland).
Standard Specifications for Wood Poles
www.fpl.fs.fed.usSTANDARD SPECIFICATIONS FOR WOOD POLES Ronald Wolfe, Research General Engineer ... dimensions, and fiber stress values for design. The special emphasis on the role of the ANSI 05.1 wood ... Douglas-fir, and oak. Thirty years later, ASTM adopted standard The ANSI 05.1 standard covers the specifications and