High-voltage resonant controller
Under output short circuit, this normally results in a nearly constant peak primary current. This condition is allowed for a maximum time set at pin 2. If the current keeps on building up despite this frequency increase, a second comparat or referenced at 1.5 V latches the device
Download High-voltage resonant controller
Information
Domain:
Source:
Link to this page:
Documents from same domain
Low-power dual operational amplifier - st.com
www.st.comFebruary 2016 DocID2471 Rev 17 1/24 This is information on a product in full production. www.st.com LM2904, LM2904A Low-power dual operational amplifier
AN3128 Application note - st.com
www.st.comJune 2011 Doc ID 16918 Rev 5 1/105 AN3128 Application note STM32 embedded graphic objects/touchscreen library Introduction This library is a firmware package which contains a collection of routines, data structures,
AN4767 Application note - st.com
www.st.comDocID028380 Rev 2 7/16 AN4767 Dual bank use cases 15 With dual bank, all the manipulation with the other bank is just another task of the main program.
AN3155 Application note - st.com
www.st.comOctober 2016 DocID17066 Rev 7 1/37 1 AN3155 Application note USART protocol used in the STM32 bootloader Introduction This application note describes the USART protocol used in the STM32 microcontroller
USB Power Delivery and Type-C - st.com
www.st.comUSB Type -C Overview USB Power Delivery specification introduces USB Type-C receptacle, plug and cable; they provide a smaller, thinner and more robust alternative to existing USB interconnect.
Datasheet - L78 - Positive voltage regulator ICs - …
www.st.comTO- 2 2 0 TO-2 2 0 F P DPAK D² PAK Features • Output current up to 1.5 A • Output voltages of 5; 6; 8; 8.5; 9; 12; 15; 18; 24 V • Thermal overload protection
AN2867 Application note - st.com
www.st.comMay 2017 DocID15287 Rev 11 1/43 1 AN2867 Application note Oscillator design guide for STM8AF/AL/S and STM32 microcontrollers Introduction Many designers know oscillators based on Pierce-Gate topology (hereinafter referred to as
AN4776 Application note - st.com
www.st.comMay 2017 DocID028459 Rev 2 1/73 1 AN4776 Application note General-purpose timer cookbook Introduction The timer peripheral is part of …
120-volt, 100-watt, DMOS audio amplifier with mute …
www.st.comSeptember 2010 Doc ID 6744 Rev 8 1/21 21 TDA7293 120-volt, 100-watt, DMOS audio amplifier with mute and standby Features Multipower BCD technology Very high operating voltage range (±50 V)
Electronic transformer for a 12V halogen lamp - …
www.st.comAPPLICATION NOTE AN528/0999 1/4 ELECTRONIC TRANSFORMER FOR A 12V HALOGEN LAMP by P. Fichera, R. Scollo 1. INTRODUCTION Lighting that uses halogen lamps is commonly found
Related documents
Understanding LED Drivers - 1000Bulbs.com
www.1000bulbs.comconstant-current driver, within the LED module. These LEDs require one stable voltage, usually 12V DC or 24V DC. In the example below to the right, the output voltage is 24V DC, and the output current is a maximum of 1.04A. AC LED Drivers
Lecture 10: Basics of Atomic Force Microscope (AFM)
my.eng.utah.eduConstant Force: • In this mode, the deflection of the cantilever can be used as input to a feedback circuit that moves the scanner up and down in . z, responding to the topography by keeping the cantilever deflection constant. • With the cantilever deflection held constant, the total force applied to the sample is constant.
ECEN720: High-Speed Links Circuits and Systems Spring 2021
people.engr.tamu.edu• Driver current is ideally constant, resulting in low dI/dt noise • Dual current sources allow for good PSRR, but headroom can be a problem in low-voltage technologies • Differential peak-to-peak RX swing is IR with double termination. Current-Mode Logic (CML) Driver 20
LTC3780 (Rev G)
www.analog.comIQ Input DC Supply Current Normal Standby Shutdown Supply Current (Note 4) VRUN = 0V, VSTBYMD > 2V VRUN = 0V, VSTBYMD = Open 2400 1500 55 70 µA µA µA VFCB Forced Continuous Threshold 0.76 0.800 0.84 V IFCB Forced Continuous Pin Current VFCB = 0.85V –0.30 –0.18 –0.1 µA VBINHIBIT Burst Inhibit (Constant Frequency) Threshold Measured at ...
A Fortran Tutorial - University of Utah
www.inscc.utah.eduThe simplest form of an expression is a constant. There are 6 types of constants, corresponding to the 6 data types. Here are some integer constants: 1 0 -100 32767 +15 Then we have real constants: 1.0 -0.25 2.0E6 3.333E-1 The E-notation means that you should multiply the constant by 10 raised to the power following the "E".
General Description Features - Diodes Incorporated
www.diodes.comwith 350mA current limit, and the AP3015A is for lower power systems with 100mA current limit. The AP3015/A feature a wide input voltage. The oper-ation voltage is ranged from 1.2Vto 12V (1V to 12V for AP3015A). A current limited, fixed off-time con-trol scheme conserves operating current, resulting in high efficiency over a broad range of load ...
1.5A, Low Voltage, Low Quiescent Current LDO Regulator ...
ww1.microchip.comDec 08, 2006 · Output Short Circuit Current IOUT_SC —2.2 — AVIN = Note 1, RLOAD <0.1Ω, Peak Current Adjust Pin Characteristics (Adjustable Output Only) Adjust Pin Reference Voltage VADJ 0.402 0.410 0.418 VVIN = 2.3V to VIN =6.0V, IOUT = 1 mA Adjust Pin Leakage Current IADJ-10 ±0.01 +10 nA VIN = 6.0V, VADJ =0Vto6V Adjust Temperature Coefficient TCVOUT ...
MCP1826/MCP1826S Data Sheet - Microchip Technology
ww1.microchip.comNov 29, 2012 · Output Short Circuit Current I OUT_SC —2.2 — ARLOAD <0.1 , Peak Current Adjust Pin Characteristics (Adjustable Output Only) Adjust Pin Reference Voltage V ADJ 0.402 0.410 0.418 VVIN = 2.3V to VIN =6.0V, IOUT = 1 mA Adjust Pin Leakage Current I ADJ-10 ±0.01 +10 nA VIN = 6.0V, VADJ =0Vto6V Adjust Temperature Coefficient TCV OUT — 40 ...