High-voltage resonant controller - STMicroelectronics
The pin is to be connected to the high-voltage input bus with a resistor divider to perform either AC or DC (in systems with PFC) brownout protection. A voltage below 1.25 V shuts down (not latched) the IC, lowers its consumption and discharges the soft-start capacitor. IC’s operation is re-enabled (soft-started) as the voltage exceeds 1.25 V.
Download High-voltage resonant controller - STMicroelectronics
Information
Domain:
Source:
Link to this page:
Documents from same domain
Low-power dual operational amplifier - st.com
www.st.comFebruary 2016 DocID2471 Rev 17 1/24 This is information on a product in full production. www.st.com LM2904, LM2904A Low-power dual operational amplifier
AN3128 Application note - st.com
www.st.comJune 2011 Doc ID 16918 Rev 5 1/105 AN3128 Application note STM32 embedded graphic objects/touchscreen library Introduction This library is a firmware package which contains a collection of routines, data structures,
AN4767 Application note - st.com
www.st.comDocID028380 Rev 2 7/16 AN4767 Dual bank use cases 15 With dual bank, all the manipulation with the other bank is just another task of the main program.
AN3155 Application note - st.com
www.st.comOctober 2016 DocID17066 Rev 7 1/37 1 AN3155 Application note USART protocol used in the STM32 bootloader Introduction This application note describes the USART protocol used in the STM32 microcontroller
USB Power Delivery and Type-C - st.com
www.st.comUSB Type -C Overview USB Power Delivery specification introduces USB Type-C receptacle, plug and cable; they provide a smaller, thinner and more robust alternative to existing USB interconnect.
Datasheet - L78 - Positive voltage regulator ICs - …
www.st.comTO- 2 2 0 TO-2 2 0 F P DPAK D² PAK Features • Output current up to 1.5 A • Output voltages of 5; 6; 8; 8.5; 9; 12; 15; 18; 24 V • Thermal overload protection
AN2867 Application note - st.com
www.st.comMay 2017 DocID15287 Rev 11 1/43 1 AN2867 Application note Oscillator design guide for STM8AF/AL/S and STM32 microcontrollers Introduction Many designers know oscillators based on Pierce-Gate topology (hereinafter referred to as
AN4776 Application note - st.com
www.st.comMay 2017 DocID028459 Rev 2 1/73 1 AN4776 Application note General-purpose timer cookbook Introduction The timer peripheral is part of …
120-volt, 100-watt, DMOS audio amplifier with mute …
www.st.comSeptember 2010 Doc ID 6744 Rev 8 1/21 21 TDA7293 120-volt, 100-watt, DMOS audio amplifier with mute and standby Features Multipower BCD technology Very high operating voltage range (±50 V)
Electronic transformer for a 12V halogen lamp - …
www.st.comAPPLICATION NOTE AN528/0999 1/4 ELECTRONIC TRANSFORMER FOR A 12V HALOGEN LAMP by P. Fichera, R. Scollo 1. INTRODUCTION Lighting that uses halogen lamps is commonly found
Related documents
High Voltage Direct Current (HVDC)Transmission Systems ...
large.stanford.eduHowever, DC power at low voltage could not be transmitted over long distances, thus giving rise to high voltage alternating current (AC) electrical systems. Nevertheless, with the development of high voltage valves, it was possible to once again transmit DC power at high voltages and over long distances, giving rise to HVDC transmission systems ...
Siemens Standard Drives Application Handbook
cache.industry.siemens.com• The PWM output voltage contains many high frequency harmonics (because of the fast switching) and can be a major source of EMI. • The input rectifier draws current only at the peak of the supply waveform, so the input currents have a poor form factor ( i.e. the RMS value can be quite high - this does not mean the inverter is inefficient!)
IS/IEC 62271-1 (2007): High-Voltage Switchgear and ...
law.resource.orgIS/IEC 62271-1 (2007): High-Voltage Switchgear and Controlgear, Part 1: Common Specifications [ETD 8: High ... 4.8 Rated supply voltage of closing and opening devices and of auxiliary and control circuits ... Application of voltage at the damped oscillator ywave test .....74 Table 16 – Assessment criteria for transient disturbance immunity ...
L6235 three phase brushless DC motor driver
www.st.comAPPLICATION NOTE October 2003 1 INTRODUCTION ... High side gate drivers supply voltage versus supply voltage. Note that V S must be connected to both V SA and VSB because the bootstrap voltage (at V BOOT pin) is the same for the two H-bridges. The integrated DMOS have a rated Drain-Source breakdown voltage of 60 V. However
INA3221 Triple-Channel, High-Side Measurement, Shunt and ...
www.ti.comOperating supply voltage 2.7 5.5 V Operating temperature, T A –40 125 °C (1) For more information about traditional and new thermal metrics, see the Semiconductor and IC Package Thermal Metrics application
PCA9306 Dual Bidirectional I2C Bus and SMBus Voltage-Level ...
www.ti.comSCL2 6 C2 I/O Serial clock, high-voltage side SDA1 4 D1 I/O Serial data, low-voltage side SDA2 5 D2 I/O Serial data, high-voltage side V. REF1. 2 B1 I Low-voltage-side reference supply voltage for SCL1 and SDA1 V. REF2. 7 B2 I High-voltage-side reference supply voltage for SCL2 and SDA2. PCA9306. SCPS113N – OCTOBER 2004 – REVISED OCTOBER ...
ELECTRICIT Y SUPPLY APPLICATION HANDBOOK
www.tnb.com.myactual supply voltage provided depends on the individual applicant’s load requirements (refer to Connection Guideline clause 3.1 – Maximum Demand levels and supply scheme):- It should be noted that voltages other than the above classifications is not provided by TNB.