High-voltage resonant controller - STMicroelectronics
Line sensing input. The pin is to be connected to the high-voltage input bus with a resistor divider to perform either AC or DC (in systems with PFC) brownout protection. A voltage below 1.25 V shuts down (not latched) the IC, lowers its consumption and discharges the …
Download High-voltage resonant controller - STMicroelectronics
Information
Domain:
Source:
Link to this page:
Documents from same domain
Low-power dual operational amplifier - st.com
www.st.comFebruary 2016 DocID2471 Rev 17 1/24 This is information on a product in full production. www.st.com LM2904, LM2904A Low-power dual operational amplifier
AN3128 Application note - st.com
www.st.comJune 2011 Doc ID 16918 Rev 5 1/105 AN3128 Application note STM32 embedded graphic objects/touchscreen library Introduction This library is a firmware package which contains a collection of routines, data structures,
AN4767 Application note - st.com
www.st.comDocID028380 Rev 2 7/16 AN4767 Dual bank use cases 15 With dual bank, all the manipulation with the other bank is just another task of the main program.
AN3155 Application note - st.com
www.st.comOctober 2016 DocID17066 Rev 7 1/37 1 AN3155 Application note USART protocol used in the STM32 bootloader Introduction This application note describes the USART protocol used in the STM32 microcontroller
USB Power Delivery and Type-C - st.com
www.st.comUSB Type -C Overview USB Power Delivery specification introduces USB Type-C receptacle, plug and cable; they provide a smaller, thinner and more robust alternative to existing USB interconnect.
Datasheet - L78 - Positive voltage regulator ICs - …
www.st.comTO- 2 2 0 TO-2 2 0 F P DPAK D² PAK Features • Output current up to 1.5 A • Output voltages of 5; 6; 8; 8.5; 9; 12; 15; 18; 24 V • Thermal overload protection
AN2867 Application note - st.com
www.st.comMay 2017 DocID15287 Rev 11 1/43 1 AN2867 Application note Oscillator design guide for STM8AF/AL/S and STM32 microcontrollers Introduction Many designers know oscillators based on Pierce-Gate topology (hereinafter referred to as
AN4776 Application note - st.com
www.st.comMay 2017 DocID028459 Rev 2 1/73 1 AN4776 Application note General-purpose timer cookbook Introduction The timer peripheral is part of …
120-volt, 100-watt, DMOS audio amplifier with mute …
www.st.comSeptember 2010 Doc ID 6744 Rev 8 1/21 21 TDA7293 120-volt, 100-watt, DMOS audio amplifier with mute and standby Features Multipower BCD technology Very high operating voltage range (±50 V)
Electronic transformer for a 12V halogen lamp - …
www.st.comAPPLICATION NOTE AN528/0999 1/4 ELECTRONIC TRANSFORMER FOR A 12V HALOGEN LAMP by P. Fichera, R. Scollo 1. INTRODUCTION Lighting that uses halogen lamps is commonly found
Related documents
CSS / CSSH Series ± 50 - 0.001 - 0.003 ± 15 0.007 - 0.1 0 ...
seielect.comUltra-precision Metal Alloy Current Sensing Chip Resistor Stackpole Electronics, Inc. Resistive Product Solutions Performance Characteristics 0.051 0.137 0.0051 - 0.1 R1: resistance of room temperature (T1) Mechanical Specifications (4527) Mechanical Specifications 1206 – 2728 (cont.) Test Test Method Test Specification Test Condition
Motor Control Sensor Feedback Circuits
ww1.microchip.comsignificant impact on the system if the sensing resistor is small and the resulting voltage drop across the shunt is small compared to the supply voltage. In contrast, low-side monitoring disrupts the ground path of the load, which can cause noise and EMI problems in the system. Low-side current measurements are often chosen
Current Sensing Circuit Concepts and Fundamentals
ww1.microchip.comHowever, the voltage drop across the sensing resistor may become low enough to be comparable to the input offset voltage of subsequent analog conditioning circuit, which would compromise the measurement accuracy. In addition, the current sensing resistor’s inherent inductance must be low, if the measured current has a large high-frequency ...
50 g shock NI 9237
www.ni.comresistor of known value across one arm of the bridge, creating a known strain-induced change in resistance. You can then measure the output of the bridge and compare it to the expected voltage value. You can use the results to correct gain errors in the entire measurement path, or to simply verify general operation to gain confidence in the setup.
CHIP RESISTORS - Samsung Electro-Mechanics
www.samsungsem.comMetal_Current Sensing Resistor(M_CSR) Metal Plate_Clad Type(RLP, RLC) High Power Chip Resistor General Standard(RCW) High Voltage Chip Resistor (RCV) Anti-Sulfur Resistor General Standard(RCS), Flat Type(RFS), Convex Type(RPS) Lead free Chip Resistor General Standard, Array Type, Anti-Sulfur Type Center Common Array Resistor(CCA)
AN5306 Introduction Application note - STMicroelectronics
www.st.comA voltage is applied to Uin on the negative OPAMP input of Udiff through R1 resistor. This increase on the negative input causes a voltage decrease on Uout – due to the ... (current and voltage sensing, control loop) • Light control applications (current and voltage sensing) • Analog sensors measurement applications (thermometers, low ...
Power Metal Strip Resistors, Low Value (Down to 0.0005 Ω ...
www.vishay.comsensing, voltage division and pulse applications • Proprietary processing technique produces extremely low resistance values (down to 0.0005 Ω) ... Flame retardance test may not be applicable to some resistor technologies Notes • Part marking: value; tolerance: due to resistor size limitations some resistors will be marked with only the ...
Power Metal Strip Resistors, Very High Power (to 3 W), Low ...
www.vishay.comsensing, voltage division and pulse applications • Proprietary processing technique produces extremely low resistance values (down to 0.0005 Ω) ... Flame retardance test may not be applicable to some resistor technologies Notes • Part marking: value; tolerance: due to resistor size limitations some resistors will be marked with only the ...