Measuring Interrupt Latency - NXP
of an Interrupt Request (IRQ) and the start of the respective Interrupt Service Routine (ISR). The interrupt latency is expressed in core clock cycles. 5.There is another exact definition-the number of clock cycles from the assertion of the interrupt request to the first ISR instruction executed, as shown in Figure 6.1. Conclusion
Download Measuring Interrupt Latency - NXP
Information
Domain:
Source:
Link to this page:
Documents from same domain
AN10441 Level shifting techniques in I2C-bus design
www.nxp.comDocument information AN10441 Level shifting techniques in I2C-bus design Rev. 01 — 18 June 2007 Application note Info Content Keywords I2C-bus, level shifting Abstract Logic level shifting may be required when interfacing legacy devices with
AN3234: Washing Machine Three-Phase AC …
www.nxp.comWashing Machine Three-Phase AC Induction Motor Drive, Rev. 0 Indirect Vector Control 4 Freescale Semiconductor If you are looking for more theory on the field ...
1. General description - nxp.com
www.nxp.com1. General description The TJA1044 is part of the Mantis family of high-speed CAN transceivers. It provides an interface between a Controller Area Network (CAN) protocol controller and the physical
PCA9570 Remote 4-bit general purpose outputs for 1 MHz …
www.nxp.com1. General description The PCA9570 is a CMOS device that provides 4 bits of General Purpose parallel Output (GPO) expansion in low voltage processor and handheld battery powered mobile
P82B96 Dual bidirectional bus buffer - nxp.com
www.nxp.com1. General description The P82B96 is a bipolar IC that creates a non-latching, bidirectional, logic interface between the normal I2C-bus and a range of other bus configurations.It can interface
S32K144 EVB Quick Start Guide - NXP Semiconductors
www.nxp.comJ14 SWD connector. 3 EXTERNAL USE S32K144 EVBFeatures: ... USB connector of the USB cable to micro-B port J7 on the S32K144EVB. ... Windows, Linux and Mac operating systems. Using the MSD Flash Programmer 1. Locate the .srec file of your project , file is under the
Three-Phase BLDC Motor Sensorless Control Using …
www.nxp.comThis document describes the design of a three-phase brushless DC motor (BLDC motor) drive based on Freescale’s MC56F8013 and MC56F8023 dedicated motor control device. Brushless DC motors are popular in a wide application area.
AN11443 BFU550XR ISM 433 MHz LNA design - nxp.com
www.nxp.comAN11443 BFU550XR ISM 433 MHz LNA design Rev. 1 — 23 January 2014 Application note . Document information Info Content Keywords BFU520, BFU530, BFU550 series, ISM-band, 433MHz 866MHz Abstract This document describes an ISM Frequency LNA design on BFU5xxXR Starter kit
DSP56156 16-Bit Digital Signal Processor - nxp.com
www.nxp.comThe DSP56156 is a general-purpose MPU-style Digital Signal Processor (DSP). On a single semi- conductor chip, the DSP56156 comprises a very efficient 16-bit digital signal processing core, pro-
SAA7706H Car radio Digital Signal Processor (DSP)
www.nxp.comCar radio Digital Signal Processor (DSP) SAA7706H This text is here in white to force landscape pages to be rotated correctly when browsing through the pdf in the Acrobat reader.This text is here in _white to force landscape pages to be rotated correctly when browsing through the pdf in the Acrobat reader.This text is here inThis text is here in
Related documents
Interrupts C - Uppsala University
www.signal.uu.seC.4 FEATURES OF INTERRUPT SERVICE ROUTINES An interrupt service routine (ISR) is a special routine that is executed outside of the normal program flow. An ISR is invoked in response to a particular interrupt occurring at an undetermined time. Since an interrupt occurs at an unknown time, it cannot return a value directly to a program.
Low-voltage translating 16-bit I2C-bus/SMBus I/O ... - NXP
www.nxp.comThis minimizes the host’s interrupt service response for fast moving inputs. The device Port P outputs have 25 mA sink capabilities for directly driving LEDs while consuming low device current. One hardware pin (ADDR) can be used to program and vary the fixed I2C-bus address
SDCC Compiler User Guide
sdcc.sourceforge.netMay 02, 2022 · CONTENTS CONTENTS 3.1.7 Implementation-defined behavior. . . . . . . . . . . . . . . . . . . . . . . . . . . . . .27 3.1.7.1 Translation ...
LTC2954 Pushbutton On/Off Controller with µP Interrupt ...
www.analog.comController with µP Interrupt The LTC®2954 is a pushbutton on/off controller that manages system power via a pushbutton interface. An enable output toggles system power while an interrupt output provides debounced pushbutton status. The inter-rupt output can be used in menu driven applications to request a system power-down. A power kill input ...
Interrupt handling - UMD
classweb.ece.umd.eduinterrupt can then be serviced by an interrupt service routine (ISR). Interrupt handling 5 Figure 1.3 Example of a simple interrupt system The interrupt handler is the routine that is executed when an interrupt occurs and an ISR is a routine that acts on …
Computer Time Synchronization - NIST
tf.nist.govequivalent device). This timer-counter generates an interrupt every 54.936 milliseconds, or about 18.2 times per second. The computer's BIOS (Basic Input Output System) contains a software routine that counts the interrupt requests and generates a time-of-day clock that can Computer Time Synchronization Michael Lombardi Time and Frequency Division
Section 8. Interrupts - Microchip Technology
ww1.microchip.comGenerally the interrupt flag bit(s) must be cleared in software before re-enabling the global inter-rupt to avoid recursive interrupts. Once in the interrupt service routine the source(s) of the interrupt can be determined by polling the interrupt flag bits. Individual interrupt flag bits are set regardless of the status of their