nRF5 Series: Developing with SEGGER Embedded Studio
• Embedded Studio for ARM (version 3.30 or later) • J-Link Software and Documentation Pack (version 6.10g or later) 2.Install both packages. 3.Obtain and activate your free license for SES: a) Open SES. SES will automatically load a test project. b) Click Build > Build and Debug. A window asking for a license will pop up.
Download nRF5 Series: Developing with SEGGER Embedded Studio
Information
Domain:
Source:
Link to this page:
Documents from same domain
nRF52840 Product Specification
infocenter.nordicsemi.com0 a lrck sck 5
nRF52832 Product Specification
infocenter.nordicsemi.comnRF52832 Product Specification v1.4 Key features Applications • Internet of Things (IoT) • Home automation • Sensor networks • Building automation • Industrial • Retail • Personal area networks • Health/fitness sensor and monitor devices • Medical devices • Key fobs and wrist watches • Interactive entertainment devices ...
nRF52810 - Nordic Semiconductor
infocenter.nordicsemi.com• 2.4 GHz transceiver • -96 dBm sensitivity in Bluetooth ® low energy mode • Supported data rates: 1 Mbps, 2 Mbps Bluetooth ® low energy mode • -20 to +4 dBm TX power, configurable in 4 dB steps • On-chip balun (single-ended RF) • 4.6 mA peak current in TX (0 dBm) • 4.6 mA peak current in RX • RSSI (1 dB resolution) • ARM ...
Getting started with nRF5 SDK and SES (nRF51 & nRF52 …
infocenter.nordicsemi.com• Getting started with nRF Connect SDK (nRF53 Series) • Getting started with nRF Connect SDK (nRF52 Series) • Getting started with nRF5 SDK and SES (nRF51 & nRF52 Series) (this document) • Getting started with nRF5 SDK and Keil (nRF51 & nRF52 Series) Check out the Nordic DevZone for additional setup information and help. 1159720_163 v1.4 4
nRF52832 Development Kit v1.1
infocenter.nordicsemi.com1. To set up the hardware, follow the instructions in Getting started with the nRF52 Development Kit. 2. To set up the software, follow the instructions in Nordic tools and downloads in nRF5 Getting Started. Actual software required depends on your OS and Development IDE.
nRF52832 - Product Specification v1 - Nordic Semiconductor
infocenter.nordicsemi.com2 About this document Page 10 2 About this document This Product Specification is organized into chapters based on the modules and peripherals that are
nRF52811 - Nordic Semiconductor
infocenter.nordicsemi.comFeature list Features: • Bluetooth ® 5.1, IEEE 802.15.4-2006, 2.4 GHz transceiver • -97 dBm sensitivity in 1 Mbps Bluetooth ® low energy mode • -104 dBm sensitivity in 125 kbps Bluetooth
nRF52832 Product Specification
infocenter.nordicsemi.com• 3x 4-channel pulse width modulator (PWM) unit with EasyDMA • Digital microphone interface (PDM) • 5x 32-bit timer with counter mode • Up to 3x SPI master/slave with EasyDMA • Up to 2x I2C compatible 2-wire master/slave • I2S with EasyDMA • UART (CTS/RTS) with EasyDMA • Programmable peripheral interconnect (PPI)
nPM1100 - Nordic Semiconductor
infocenter.nordicsemi.comSYSREG also implements configurable current limiting from VBUS , and USB port detection. When VBUS is disconnected, SYSREG ensures the device enters Ultra-Low Power mode to minimize quiescent current. Reverse current protection is enabled when VBUS<VBAT. See SYSREG — System regulator on page 15 for more information and electrical parameters.
nRF9160 - Nordic Semiconductor
infocenter.nordicsemi.com• Power saving features: DRX, eDRX, PSM • IP v4/v6 stack • Secure socket (TLS/DTLS) API Current consumption @ 3.7 V: • Power saving mode (PSM) floor current: 4 µA • Application core idle: 1.8 µA • Modem: 2.2 µA • eDRX @ 82.91s: 19 µA Applications: • Sensor networks • Logistics and asset tracking • Smart energy
Related documents
Alcatel-Lucent OmniSwitch 6350 - al-enterprise.com
www.al-enterprise.comGigabit Ethernet LAN switch family The Alcatel-Lucent OmniSwitch® 6350 Stackable family is a series of fixed-configuration Gigabit Ethernet switches available as 10-, 24- and 48-port, Power-over-Ethernet (PoE) and non-PoE models to create the exact network for your small business. The network capabilities of the OmniSwitch
Understanding the I2C Bus - Embedded processing
www.ti.comFigure 1 shows a typical I2C bus for an embedded system, where multiple slave devices are used. The microcontroller represents the I2C master, and controls the IO ... example of a single-register device would be an 8-bit I2C switch, which is controlled via I2C commands. Since it has 1 bit to enable or disable a channel, there is only 1 register ...
STM32 microcontroller GPIO configuration for hardware ...
www.st.comNote: In Figure 1 and Figure 2, the analog switch in the dotted square is optional. Its presence depends on the STM32 product considered. The analog switch is controlled by enabling analog peripheral on the given pin (not by setting the GPIO in the analog mode). Refer to the product datasheet for details. In Figure 1 and Figure 2, the V. DD
The ARM Instruction Set - University of Texas at Austin
users.ece.utexas.eduEE382N-4 Embedded Systems Architecture Thumb Thumb is a 16 ‐ bit instruction set – Optimized for code density from C code – Improved performance form narrow memory – Subset of the functionality of the ARM instruction set Core has two execution states –ARM and Thumb – Switch between them using BX instruction
DHI-VTH2421FW-P/DHI-VTH2421FB-P - Dahuasecurity.com
www.dahuasecurity.comMar 04, 2020 · · Embedded 8GB SD card · Support standard PoE Technical Specification Main Processor High performace embedded processor Operating System Embedded LINUX OS Screen Type Capacitive screen Display 7-inch TFT screen Resolution 1024 × 600 Video Compression H.264 Audio Compression G.711A/G.711U/PCM Audio Input 1 channel all …
Alcatel-Lucent OmniSwitch 6900 - al-enterprise.com
www.al-enterprise.com• AOS-embedded scripting capabilities supporting Python and Bash programming. • N_Port ID virtualization (NPIV) FCoE to FC forwarder gateway supported using the OS-XNI-U12E module. • FC to FCoE gateway, FC tunneling over FCoE, FC inter-switch link (ISL) tunneling, F-port virtualization, FCoE Initialization Protocol (FIP) snooping