nRF52811 - Nordic Semiconductor

nRF52832 Product Specification

nRF52832 Product Specification v1.4 Key features Applications • Internet of Things (IoT) • Home automation • Sensor networks • Building automation • Industrial • Retail • Personal area networks • Health/fitness sensor and monitor devices • Medical devices • Key fobs and wrist watches • Interactive entertainment devices ...

  Product, Specification, Nrf52832 product specification, Nrf52832, Nrf52832 product specification v1

nRF52840 Product Specification

0 a lrck sck 5

nRF52810 - Nordic Semiconductor

• 2.4 GHz transceiver • -96 dBm sensitivity in Bluetooth ® low energy mode • Supported data rates: 1 Mbps, 2 Mbps Bluetooth ® low energy mode • -20 to +4 dBm TX power, configurable in 4 dB steps • On-chip balun (single-ended RF) • 4.6 mA peak current in TX (0 dBm) • 4.6 mA peak current in RX • RSSI (1 dB resolution) • ARM ...

  4 ghz, To 4, Nrf52810

Getting started with nRF5 SDK and SES (nRF51 & nRF52 …

• Getting started with nRF Connect SDK (nRF53 Series) • Getting started with nRF Connect SDK (nRF52 Series) • Getting started with nRF5 SDK and SES (nRF51 & nRF52 Series) (this document) • Getting started with nRF5 SDK and Keil (nRF51 & nRF52 Series) Check out the Nordic DevZone for additional setup information and help. 1159720_163 v1.4 4

  Series, With, Getting, Started, Getting started, Like, Getting started with nrf5 sdk and ses, Nrf5, Nrf51 amp nrf52, Nrf51, Nrf52, Nrf51 amp nrf52 series, Getting started with nrf5 sdk and keil

Getting Started - Nordic Semiconductor

There are two Getting Started Guides that show how to work with different IDEs: • nRF5 Series: Developing with SEGGER Embedded Studio (this document) • nRF5 Series: Developing on Windows with ARM Keil MDK Check out the Nordic DevZone for additional setup information and help. 1159720_163 v1.3 4

  Getting, Started, Getting started, Like, Segger, Arm keil mdk

nRF52832 Development Kit v1.1

1. To set up the hardware, follow the instructions in Getting started with the nRF52 Development Kit. 2. To set up the software, follow the instructions in Nordic tools and downloads in nRF5 Getting Started. Actual software required depends on your OS and Development IDE.

  Getting, Started, Getting started, Nrf5, Nrf5 getting started

nRF52832 - Product Specification v1 - Nordic Semiconductor

2 About this document Page 10 2 About this document This Product Specification is organized into chapters based on the modules and peripherals that are

nRF52832 Product Specification

• 3x 4-channel pulse width modulator (PWM) unit with EasyDMA • Digital microphone interface (PDM) • 5x 32-bit timer with counter mode • Up to 3x SPI master/slave with EasyDMA • Up to 2x I2C compatible 2-wire master/slave • I2S with EasyDMA • UART (CTS/RTS) with EasyDMA • Programmable peripheral interconnect (PPI)

  Channel

nPM1100 - Nordic Semiconductor

SYSREG also implements configurable current limiting from VBUS , and USB port detection. When VBUS is disconnected, SYSREG ensures the device enters Ultra-Low Power mode to minimize quiescent current. Reverse current protection is enabled when VBUS<VBAT. See SYSREG — System regulator on page 15 for more information and electrical parameters.

  Power, Current, Limiting, Current limiting, Npm1100

nRF9160 - Nordic Semiconductor

• Power saving features: DRX, eDRX, PSM • IP v4/v6 stack • Secure socket (TLS/DTLS) API Current consumption @ 3.7 V: • Power saving mode (PSM) floor current: 4 µA • Application core idle: 1.8 µA • Modem: 2.2 µA • eDRX @ 82.91s: 19 µA Applications: • Sensor networks • Logistics and asset tracking • Smart energy

  Nrf9160

Type 1 and Type 2 Surge Protective Devices (SPDs)

A commercial or industrial facility will have surge protection devices at the incoming AC line, at power distribution, and near critical electrically powered equipment Global warming is projected to increase lighting strikes by 12% per degree Celsius of global warming and about 50% over this century. Source: Science Magazine

  Industrial, Lighting

The Road to Zero - GOV.UK

29. Future-proofing our streets. We want all new street lighting columns to include charging points, where appropriately located, in areas with current on-street parking provision. 30. Continuing to provide grant support through the Electric Vehicle Homecharge Scheme (EVHS) until March 2019, with installations becoming smart enabled. 31.

  Road, Lighting, Zero, Road to zero