Example: biology
nRF52832 Product Specification
• 3x 4-channel pulse width modulator (PWM) unit with EasyDMA • Digital microphone interface (PDM) • 5x 32-bit timer with counter mode • Up to 3x SPI master/slave with EasyDMA • Up to 2x I2C compatible 2-wire master/slave • I2S with EasyDMA • UART (CTS/RTS) with EasyDMA • Programmable peripheral interconnect (PPI)
Tags:
Information
Domain:
Source:
Link to this page:
Documents from same domain
nRF52840 Product Specification
infocenter.nordicsemi.com0 a lrck sck 5
nRF52832 Product Specification
infocenter.nordicsemi.comnRF52832 Product Specification v1.4 Key features Applications • Internet of Things (IoT) • Home automation • Sensor networks • Building automation • Industrial • Retail • Personal area networks • Health/fitness sensor and monitor devices • Medical devices • Key fobs and wrist watches • Interactive entertainment devices ...
nRF52810 - Nordic Semiconductor
infocenter.nordicsemi.com• 2.4 GHz transceiver • -96 dBm sensitivity in Bluetooth ® low energy mode • Supported data rates: 1 Mbps, 2 Mbps Bluetooth ® low energy mode • -20 to +4 dBm TX power, configurable in 4 dB steps • On-chip balun (single-ended RF) • 4.6 mA peak current in TX (0 dBm) • 4.6 mA peak current in RX • RSSI (1 dB resolution) • ARM ...
Getting started with nRF5 SDK and SES (nRF51 & nRF52 …
infocenter.nordicsemi.com• Getting started with nRF Connect SDK (nRF53 Series) • Getting started with nRF Connect SDK (nRF52 Series) • Getting started with nRF5 SDK and SES (nRF51 & nRF52 Series) (this document) • Getting started with nRF5 SDK and Keil (nRF51 & nRF52 Series) Check out the Nordic DevZone for additional setup information and help. 1159720_163 v1.4 4
Getting Started - Nordic Semiconductor
infocenter.nordicsemi.comThere are two Getting Started Guides that show how to work with different IDEs: • nRF5 Series: Developing with SEGGER Embedded Studio (this document) • nRF5 Series: Developing on Windows with ARM Keil MDK Check out the Nordic DevZone for additional setup information and help. 1159720_163 v1.3 4
nRF52832 Development Kit v1.1
infocenter.nordicsemi.com1. To set up the hardware, follow the instructions in Getting started with the nRF52 Development Kit. 2. To set up the software, follow the instructions in Nordic tools and downloads in nRF5 Getting Started. Actual software required depends on your OS and Development IDE.
nRF52832 - Product Specification v1 - Nordic Semiconductor
infocenter.nordicsemi.com2 About this document Page 10 2 About this document This Product Specification is organized into chapters based on the modules and peripherals that are
nRF52811 - Nordic Semiconductor
infocenter.nordicsemi.comFeature list Features: • Bluetooth ® 5.1, IEEE 802.15.4-2006, 2.4 GHz transceiver • -97 dBm sensitivity in 1 Mbps Bluetooth ® low energy mode • -104 dBm sensitivity in 125 kbps Bluetooth
nPM1100 - Nordic Semiconductor
infocenter.nordicsemi.comSYSREG also implements configurable current limiting from VBUS , and USB port detection. When VBUS is disconnected, SYSREG ensures the device enters Ultra-Low Power mode to minimize quiescent current. Reverse current protection is enabled when VBUS<VBAT. See SYSREG — System regulator on page 15 for more information and electrical parameters.
nRF9160 - Nordic Semiconductor
infocenter.nordicsemi.com• Power saving features: DRX, eDRX, PSM • IP v4/v6 stack • Secure socket (TLS/DTLS) API Current consumption @ 3.7 V: • Power saving mode (PSM) floor current: 4 µA • Application core idle: 1.8 µA • Modem: 2.2 µA • eDRX @ 82.91s: 19 µA Applications: • Sensor networks • Logistics and asset tracking • Smart energy
Related documents
CONFIDENTIAL ADVANCE INFORMATION ES9018 …
www.esstech.com2 DAC1 O Differential Positive Analog Output 1 ... The ramp rate is 0.0078125 x fs dB/s, where fs = DATA_CLK / 64 in PCM serial or DSD modes, or SPDIF sampling rate in SPDIF mode. Automute ... Each output channel has its own attenuation circuit. The attenuation for each channel is controlled independently.
Analog to Digital Converters - gatech.edu
ume.gatech.eduOutput digital signal 2 steps Sampling and Holding (S/H) ... Output is a serial bit stream with # of 1’s proportional to V in ... 8-channel analog/digital input multiplexer
LTC1286/LTC1298 - Micropower Sampling 12 ... - Analog …
www.analog.comThe LTC1286 has a single differential analog input. The LTC1298 offers a software selectable 2-channel MUX. On-chip serial ports allow efficient data transfer to a wide range of microprocessors and microcontrollers over three wires. This, coupled with micropower consumption, makes remote location possible and facilitates transmitting data
ES9038Q2M 32-Bit Stereo Mobile Audio DAC Analog …
file2.dzsc.com10 PowerAVCC_L Power DAC analog output stage reference supply for the Left Channel 11 AGND_L Ground DAC analog output stage ground for the Left Channel 12 VCCA Power Analog +3.3V for OSC 13 DVCC Power Power Digital +1.8V to +3.3V 14 DGND Ground Ground Digital Ground 15 DVDD Power Digital Core Voltage, nominally +1.2V, supplied by an internal ...
Integrated Optical Module for Smoke ... - Analog Devices
www.analog.comdetection. The analog front end (AFE) features best- in-class rejection of signal offset and corruption due to modulated interference commonly caused by ambient light. The data output and functional configuration occur over a 1.8 2V I C interface or serial peripheral interface (SPI) port. FUNCTIONAL BLOCK DIAGRAM . TIME SLOT A TIME SLOT B ...
Omni ision Preliminary Datasheet Advanced Information
www.uctronics.comfed to two 10-bit analog-to-digital (A/D) converters, one for G channel and one shared by the BR channels. These A/D converters operate at speeds up to 20 MHz and are fully synchronous to the pixel rate (actual conversion rate is related to the frame rate). Channel Balance The amplified signals are then balanced with a channel balance block.
cDAQ-9189 Specifications - National Instruments
www.ni.comSerial modules 63 samples per slot Note When parallel modules in a digital task are in slots 1 through 4, FIFO is 2,047 samples per slot for all slots. When any parallel module in a digital task is in slots 5 through 8, FIFO is 1,023 samples per slot for all eight slots.