Solving Convergence Problems - Intusoft
• Make sure that there are no unrealistic model parameters; especially if you have manually entered the model into the netlist. • Make sure that all resistors have a value. In SPICE 3, resistors without values are given a default value of 1 kOhm. •Negative capacitor and inductor values are allowed in SPICE 3.
Download Solving Convergence Problems - Intusoft
Information
Domain:
Source:
Link to this page:
Documents from same domain
Average simulations of FLYBACK converters with …
www.intusoft.com1 Average simulations of FLYBACK converters with SPICE3 Christophe BASSO May 1996 Within the wide family of Switch Mode Power …
A SPICE MODEL FOR IGBTs - Intusoft
www.intusoft.comby each input for the device in Table 1. SPICEMOD is so intelligent that a reasonable first order de-vice model can be obtained by simply entering the volt-age and current ratings of …
Write your own generic SPICE Power Supplies …
www.intusoft.com1 Write your own generic SPICE Power Supplies controller models Christophe BASSO November 1996 Manuscript for PCIM US Simulating the switching behavior of a Switch Mode Power Supply (SMPS) is not always an easy task.
Article Title: SPICE Models For Power Electronics
www.intusoft.comArticle Title: "SPICE Models For Power Electronics" Author: L.G. Meares and Charles E. Hymowitz Abstract: Due to the increasing complexity of power …
Modeling Non-Ideal Inductors in SPICE - Intusoft
www.intusoft.comIntroduction Modelling of inductors and inductive elements in SPICE has always been of low importance to analogue designers. This is …
A SPICE MODEL FOR TRIACs (preliminary version; …
www.intusoft.comIntroduction Berkeley SPICE is the most popular program for simulat-ing the behavior of electronic circuits. The biggest stum-bling block most engineers run …
Related documents
A SPICE MODEL FOR IGBTs - Intusoft
www.intusoft.com.MODEL DLIM D (IS=100N).ENDS the turn-off tail time. The OFF control parameter can be added to aid DC convergence by starting DC calculations with Q1 turned off. MOSFET M1 emulates the input MOSFET [3, 4]. The Berkeley SPICE Level=3 model is used in the .MODEL MFIN statement in order to better model modern device characteristics.
Automotive SPICE® Process Reference Model
www.automotivespice.comThe Automotive SPICE® PRM is used in conjunction with the Automotive SPICE® Process Assessment Model (PAM) when performing an assessment. The Automotive SPICE® PAM provides additional indicators of process performance and process capability tailored to the needs of performing assessments of software process capability of automotive suppliers.
Automotive SPICE
www.automotivespice.comThis document is a revision of the Automotive SPICE process assessment model 2.5 and the process reference model 4.5, which has been developed under the Automotive SPICE initiative by consensus of the car manufacturers within the Automotive Special Interest Group (SIG), a joint
Spice model tutorial for Power MOSFETs
www.st.comSpice model tutorial for Power MOSFETs Introduction This document describes ST’s Spice model versions available for Power MOSFETs. This is a guide designed to support user choosing the best model for his goals. In fact, it explains the features of different model versions both in terms of static and dynamic characteristics
ngspice user manual
ngspice.sourceforge.netNgspice User’s Manual Version 36 plus (ngspice development version) Holger Vogt, Marcel Hendrix, Paolo Nenzi, Dietmar Warning January 14, 2022
Orcad Capture User's Guide
www.seas.upenn.eduOrcad® Capture User’s Guide capug.book Page 1 Tuesday, May 23, 2000 12:08 PM
SPICE ‘Quick’ Reference Sheet THE GENERAL ANATOMY OF A ...
web.stanford.eduSPICE Quick Reference Sheet v1.0 THE GENERAL ANATOMY OF A SPICE DECK SPICE input file, called source file, consists of three parts. First, Data Statements describe the components and the interconnections. Then, Control Statements tell SPICE what type of analysis to perform on the circuit. Finally, Output Statements specify what
BSIM3v3.3 MOSFET Model - Ngspice, the open source Spice ...
ngspice.sourceforge.net4.4 Charge-Thickness Capacitance Model 4-14 4.5 Extrinsic Capacitance 4-19 4.5.1 Fringing Capacitance4-19 4.5.2 Overlap Capacitance4-19 CHAPTER 5: Non-Quasi Static Model 5-1 5.1 Background Information 5-1 5.2 The NQS Model 5-1 5.3 Model Formulation 5-2 5.3.1 SPICE sub-circuit for NQS model5-3 5.3.2 Relaxation time5-4
Beginner’s Guide to LTSpice - University of Toronto
www.eecg.utoronto.caon how to create one with a spice command. First, create two inductors L1 and L2 to be the two windings. Press ‘T’ to get the “enter text” dialog and check the “SPICE Directive” box. In the box, type in K1 L1 L2 k, where k is the coefficient of coupling. Normally use ‘1’ for k in case of a toroid or power transformer.
NGSPICE: Circuit Simulator
web.engr.oregonstate.edu-download ng-spice-rework-26.tar.gz to a working area.-gunzip ng-spice-rework-26.tar.gz-tar xvf ng-spice-rework-26.tar-Go into the newly created ngspice directory and type: ... Control lines tell the simulator which model & run parameters to perform, such as transient analysis or plot. Oregon State University 6. Ngspice User Guide - ECE 391