TH400 Electric Kickdown Kit Installation Instructions
Step 5:(Continued)Position the kickdown mounting bracket behind the carburetor bracket so that the 5/16" diameter holes at the top of both brackets are aligned, the small
Download TH400 Electric Kickdown Kit Installation Instructions
Information
Domain:
Source:
Link to this page:
Documents from same domain
700-R4, 4L60, and 4L60E Automatic Case Mount Shifter ...
www.lokar.comFig. 4 If you have a 4 wheel drive application that will not accept the rear mounting bracket, start the 5/16"-24 x 5/8" tension set screws into the tension set screw holes at the front and in the center of the shifter main plate. Set the mounting bracket assembly into place on top of the transmission. Fig. 4
Ford C4 and C6 Hi-Tech Kickdown Kit Installation Instructions
www.lokar.comFord C4 and C6 Hi-Tech Kickdown Kit Installation Instructions Step 5: Con( inued) t Attach the kickdown mounting bracket to the Cable Bracket using the supplied #8-32 x 1/2" button head bolt and nylock nut through the small 3/16" diameter center holes in both brackets, but do
Ford AOD Hi-Tech Kickdown Kit Installation Instructions
www.lokar.comStep 10:On the passenger side of the transmission near the tail housing, you will find three test ports. The T.V. test port is the one in the middle. Fig. 10 Remove the block off plug from the T.V. test port, and connect an oil pressure gauge with hose (not included) using a …
Back-Up Light or Neutral Safety Switch Kit Installation ...
www.lokar.comNOTE: This Kit offers the choice of a Back-Up Light Switch OR a Neutral Safety Switch, Not Both! 5/16"-18 x 1-1/4" This Kit will work with the Lokar Adjustable Column Shift Linkage EXCEPT TH400, 700-R4, 4L60E and 4L80E. Refer to Fig. 1 for the component names. Switch Installation: Step 1: Install the bracket with the switch:
Throttle Cable Installation Instructions - Lokar
www.lokar.com(NOTE: If a Lokar Kickdown Kit is being used, install the kickdown mounting bracket onto the back side of the Cable Mounting Bracket first.) Then, position the rear adjuster nut so that the threaded part of the throttle cable adjuster is approximately centered in the Cable Mounting Bracket. Reinstall the front adjuster nut. Fig. 3
TH400 Electric Kickdown Kit Installation Instructions
www.lokar.comStep 5:The kickdown mounting bracket mounts onto the back side of the Lokar Cable Bracket. The throttle cable adjuster will pass through the top hole in both the new kickdown mounting bracket AND the Cable Bracket. TOLL FREE 1-877-469-7440 • tech@lokar.com • www.lokar.com ® TH400 Electric Kickdown Kit Installation Instructions
Related documents
BMW X5 (E53) Installation Guide - lindvigs.com
lindvigs.comBMW X5 (E53) Installation Guide 12 (18) Locate the white/yellow/grey I-Bus wire in the wires going to the MID or NAV. You may have to …
SAS Visual Analytics 7.4: Installation and …
support.sas.comWhatʼs New What’s New in Installation and Configuration for SAS Visual Analytics 7.4 Overview The SAS Visual Analytics: Installation and Configuration Guide (Distributed SAS
Limited Warranty Guide and Service - fujitsu.com
www.fujitsu.comII. Limited Warranty Guide WeLcoMe Congratulations on the purchase of a Fujitsu Imaging Product! Fujitsu Imaging Products are designed to give Fujitsu end users the highest performance and
Carpet Sales Refresher Checklist 2012 02 - …
www.measurecomp.comCarpet Sales Refresher Checklist Introduction Use this checklist to verify that each D23 sales specialist and sales associate is fully prepared to sell carpet and to provide
The Home Depot Flooring Services Standard …
www.measurecomp.comPage 1 of 3 Revised 8/15/2011 The Home Depot Flooring Services Standard Practices The following is a list of flooring services standard practices as approved by The Home Depot
Clover Station
www.clover.com7 Clover Station Feature Guide English 8 Applications Register Ring Up Transactions Your home base for quickly creating and charging for orders.