Vertical Installation Technical Specification - James Hardie
Insulation capability Climate zone R-value requirement Minimum cavity insulation infill requirement 1 and 2 1.9 m2 ºC/W R2.0* 3 2.0 m2 ºC/W R2.2* Total construction R-value depends on the insulation material used and the framing ratio. The insulation material R-values specified in this table are for studs spaced at 600mm centres
Download Vertical Installation Technical Specification - James Hardie
Information
Domain:
Source:
Link to this page:
Documents from same domain
Technical Specification - jameshardie.co.nz
www.jameshardie.co.nzLinea® Weatherboard Technical Specification April 2016 New Zealand 3 1 Application and scope 1.1 APPLICATION Linea® Weatherboard is …
Design Manual - jameshardie.co.nz
www.jameshardie.co.nzFire and Acoustic Design Manual August 2017 New Zealand 3 1 Introduction readers are familiar with the relevant James Hardie cladding and lining product literature.
Design Manual - James Hardie
www.jameshardie.co.nzFigure 1: Vertical junction between Linea™ Weatherboard and James Hardie flat sheet cladding Figure 2: Vertical junction between Linea™ Weatherboard and James Hardie flat sheet cladding 4 James Hardie Cladding Junction Details Design Manual November 2016 New Zealand Flexible underlay Linea™ Weatherboard Scriber 60 x 3.15mm jolt head
Fire & Acoustic - James Hardie
www.jameshardie.co.nz3.1 External Walls - Timber Frame 8 3.2 External Walls - Steel Frame 10 3.3 Parapet & Wing Walls ... S - StriaTM Cladding ... Refer to recommended safe working practices in each specific product technical specification or installation manual
CLD Structural Cavity Batten Technical Specification
www.jameshardie.co.nzThis specification covers the use of Titan Façade Panel on buildings, where the maximum wind pressure exerted on the building façade is up to 2.5kPa (ULS). This specification is intended for use by architects or designers/ specifier and installers who …
Design Manual - James Hardie
www.jameshardie.co.nzThe specifier or other party responsible for the project must run through a risk matrix analysis as per E2/AS1 to determine which construction method is applicable to install the external cladding on the project. The designer must also ensure that the bracing capacities published in this specification are appropriate for the intended application.
jameshardie.co.nz CLD Structural Cavity Batten
www.jameshardie.co.nzPortland cement, ground sand, cellulose fibre and water. The product is easily identified by the name 'Stria Cladding' printed on the back of the panels. CLD Structural Cavity Batten is manufactured using a low density fibre cement formulation. The basic composition is Portland cement, ground sand, cellulose fibre, water and proprietary additives.
Related documents
Sound Control for Commercial and Residential Buildings ...
www.eaglerocksupply.comInsulation thickness has a more significant effect on STC ratings than does density.For a typical steel stud wall construction,the first inch of fiber glass insulation can increase the STC value 6 or more points.Each additional inch of fiber glass insulation increases the STC value from one to two points.Conversely,density variations have
Best Practice Guide External Wall Insulation - INCA
www.inca-ltd.org.ukExternal Wall Insulation Best Practice Guide This guide is issued by INCA to give general guidance on best practice. INCA and the organisations responsible for its content do not accept any liability arising in any way from relying on this guide. If you require advice on a specific issue, you should seek your own independent professional advice.
MMA: Guide to fire detailing in multi- occupancy buildings
www.labc.co.ukMMA: Guide to fire detailing in multi-occupancy buildings ... at the junction between an external cavity wall (except where the cavity wall complies with Diagram 34) and every compartment floor and ... (Ensuring Best Practice for Passive Fire Protection in Buildings) offers a complete introduction to all
BEST PRACTICE SECTION 3 GUIDES SUPERSTRUCTURE
www.nhbc.co.ukThis score line relates to the quality of build of the inner leaf of the external wall (either blockwork or timber) and any internal load-bearing partition or separating walls. ... 3.3 CAVITIES AND INSULATION 3.3 - 10 3.3 - 11 BEST PRACTICE GUIDES - SECTION 3 PAGE 8 0F 25. 3.3 CAVITIES AND INSULATION 3.3 - 12 3.3 - 13 3.3 - 14 8 BEST PRACTICE ...
Installation Guide
static-content-prod.jameshardie-digital.com.auSoft compressible insulation installed between the front of the wall studs and directly behind the external cladding can cause installation issues and is thus not recommended. Flashing All wall openings, penetrations, intersections, connections, window sills, heads and jambs must be flashed prior to cladding installation. Accessories
New rules of measurement
www.rics.orgStandards (IPMS) – both IPMS 1 (external) and IPMS 2 (internal), which set the rules for measuring gross external floor areas (GEFA) and gross internal floor areas (GIFA), respectively. NRM 2 also takes account of both the RIBA Plan of Work 2020 and …
Retrofit Room in Roof Insulation
assets.publishing.service.gov.ukRetrofit Room in Roof Insulation: guide to best practice . 5 . 1. Introduction . The built environment is one of the biggest carbon dioxide emitters, with space heating being a large proportion of this. To meet UK´s 2050 emissions targets, it is necessary to reduce carbon dioxide emissions of the existing building stock.
Valuation of properties in multi-storey, multi-occupancy ...
www.rics.org∫ rendered external wall insulation system ∫ plastic ∫ tiling systems and ∫ timber. Note: this list of cladding types is as defined by the UK government in Building Safety Programme: estimates of EWS1 requirements on residential buildings in England.