WALL PANEL INSTALLATION - Onyx Collection
for exact on-size sizing. All panels should have about 1/8" ... drill bits, and belt sanders. Fine to medium tooth finish blades work best for cutting. Make faucet holes with an electric drill and a normal hole saw bit or by using a jigsaw or circular saw. ... clearance hole in the Onyx and never screw directly into the Onyx. Always secure ...
Download WALL PANEL INSTALLATION - Onyx Collection
Information
Domain:
Source:
Link to this page:
Documents from same domain
Shower Drain Installation - Onyx Collection
www.onyxcollection.com3 4 1 2 Shower Drain Installation The picture above shows all the parts of your shower drain in the order they will be used during the installation.
Install Shower Base SBI-0518 - Onyx Collection
www.onyxcollection.comOther Helpful Suggestions & Solutions For Framing “Walk-In” Showers, it may be necessary to install the base before framing the return walls.
WALL PANEL INSTALLATION - Onyx Collection
www.onyxcollection.comWALL PANEL INSTALLATION Silicone Adhesive Panel Installation Order Cutting Notches & Holes Silicone Application about 8” apart For best results, Silicone from
18 WALL 14MOUNT SHOWER SEAT 17 5/8” 16”
www.onyxcollection.comBelvue, KS 66407 • Phone: (800) 669-9867 • Fax: (800) 393-6699 • www.onyxcollection.com Wall Preparation
Install Shower Base SBI-1120 - Onyx Collection
www.onyxcollection.comthe shower base with a drop cloth, cardboard, or a piece of OSB board or plywood (when a lot of tile work is being done this may be a good idea). Also, watch for screws, dirt, or other debris that can fall onto the base and will ... Install_Shower_Base_SBI-1120.cdr Author: kevin
Shower Drain Installation - Onyx Collection
www.onyxcollection.comInstall Drain Body in Shower Base before the Base is put in place on the floor. The Drain body is inserted from the top side and pressed firmly into place so that the Silicone Adhesive forms an even seal. 2" Drain Pipe should be centered in a hole (approximately 5" diameter) in the flooring. The top of the Pipe
Related documents
Machine Screw and Drill Size Chart (English)
eberhardt.bzClearance Hole Drills Screw Designation Tap Drill Size Close Fit Loose Fit Number Diameter Pitch Tap Size Drill Diameter Drill Diameter Drill Diameter or dia. (inch) (threads/inch) Size (inch) Size (inch) Size (inch) #0 0.06 80 0-80 3/64 0.0469 52 0.0635 50 0.07 #1 0.073 64 1-64 53 0.0595 48 0.076 46 0.081 ...
65-0090 - 7800 SERIES S7800A Keyboard Display Module
customer.honeywell.comnections to allow for sufficient clearance. 3. Use the KDM or Data ControlBus ModuleŽ as a template (Fig. 19) and mark the two screw locations, interlocking ear locations and the two plug-in connector locations. 4. Drill the pilot holes for the mounting screws. 5. Cut holes in the door panel for the interlocking ears and the two plug-in ...
Installation Guide
images.thdstatic.comup with the bottom hole from the screw removed in step 3a. NOTE: The top of the hinge rail should extend approximately 3/16” beyond the top of the door frame. 2. Pre-drill 1” deep pilot holes in door frame at each hinge and fasten using 1” unpainted screws from the pink bag in the installation kit. 1. Sweep H only: Slide the sweep ˜n (I ...
PLEASE call the storm door Solution Center at 1-800-933-3626,
images.thdstatic.comTIP: Use a screw driver to loosen and tighten screws; a drill may strip the screw holes. If screws do strip, replace 3. Remove bottom spacer (H) by pressing down on raised lip. 4. Properly discard all orange clips. 1. Set bottom of door centered in opening. Make sure orange bottom spacer (H) is sitting on door sill. 2.
Installation Guide - Windows -- 400 Series - Complementary …
www.andersenwindows.com• Drill/Driver • #2 Phillips Bit • Caulk Gun • / 16" Drill Bit • Staple Gun Parts Included ... • Size of rough opening should allow minimum ¼" clearance around entire unit, between unit frame and rough opening. Width of rough opening ... using a #10 x 1 ½" screw. For rectangular and