English Fitting Instructions: Speed Triple R, Speed …

1 1 of 6 EnglishPublication part number A9900537 issue 20 Triumph Designs Ltd. 2018 Fitting Instructions: Speed Triple 1050 from VIN 461332, Speed Triple 1050 R, Speed Triple S, Speed Tr i p l e R , S p e e d Tr i p l e R S ,Street Triple from VIN 560477, Street Triple R from VIN 560477, Street Triple RX, Street Triple R LRH (Low Ride Height), Street Triple RS, Street Triple S, Street Triple S 660cc, Daytona 675 from VIN 564948, Daytona 675 R from VIN 564948,Tiger 800, Tiger XR, Tiger XRx, Tiger Explorer, Tiger Explorer XC, Tiger Sport, Explorer XR, Explorer XRx, Explorer XC, Explorer XCx,Tiger 800 XR, Tiger 800 XRX, Tiger 800 XRX LRH, Tiger 800 XRT, Tiger 1200 XR, Tiger 1200 XRX, Tiger 1200 XRX LRH, Tiger 1200 XCX, Tiger 1200 XRT, Tiger 1200 XCA,Trophy,Street Twin, Speed Twin,Scrambler 1200 XC, Scrambler 1200 XEA9640056, A9640057, A9640105, A9640106, A9640168, A9640169A9640170 and A9640171 Thank you for choosing this Triumph genuine accessory kit.

2 This accessory kit is the product of Triumph's use of provenengineering, exhaustive testing, and continuous striving for superior reliability, safety and read all of these instructions before commencing the installation of the accessory kit in order to becomethoroughly familiar with the kit s features and the installation instructions should be considered a permanent part of your accessory kit, and should remain with it even if youraccessory-equipped motorcycle is subsequently , A9640057, A9640168 and A9640169 Parts pressure sensor2 valve2 wipe1 off 2 of 6A9640105, A9640106, A9640170 and A9640171 Parts Supplied:Note: Before Fitting this accessory kit, ensure the ownerof the motorcycle has been informed of thewarnings contained in these instructions .

3 The serial number for the tyre pressure sensor isprinted on a label which is on the sensor. Ensurethat the serial number for the front and rearsensor is recorded into the spaces provided in theOwner's Handbook prior to Fitting the tyre. The following procedure shows the installation ofkit A9640056. Although visually different theprocedure is the same for all other kits. pressure sensor2 valve2 wipe1 offWarningThe accessory kits covered in this instruction aredesigned for use on specific models of Triumphmotorcycle. The accessory kits and the modelsapplicable are listed at the start of the instruction.

4 Theyshould not be fitted to any other Triumph model or toany other manufacturer s motorcycle. Fitting anaccessory kit to a Triumph model not listed, or to anyother manufacturer s motorcycle will affect theperformance, stability and handling of the may affect the rider s ability to control themotorcycle and could cause an have Triumph approved parts, accessories andconversions fitted by a trained technician of anauthorised Triumph dealer. The fitment of parts,accessories and conversions by a technician who is notof an authorised Triumph dealer may affect thehandling, stability or other aspects of the motorcycle soperation which may result in loss of motorcycle controland an this operation, ensure that the motorcycle isstabilised and adequately supported to prevent risk ofinjury from the motorcycle torque wrench of known accurate calibration must beused when Fitting this accessory kit.

5 Failure to tightenany of the fasteners to the correct torque specificationmay result in loss of motorcycle control and an of and note the eight-digit wheel sensor ID fromeach sensor label taking care to accurately identifythe front and rear sensors. 1. Tyre pressure sensor2. ID the rear wheel as described in the proprietary tools, remove the and discard the original tyre valve from Fixing2. Tyre valve, Speed Triple 1050 the mounting hole on the wheel rim and thearea around it is free from any dirt or a seal is fitted to the tyre valve from the Tyre valve, Speed Triple 1050 shown2.

6 The tyre valve to its mounting hole in the wheelrim. Ensure for kits A9640056, A9640057,A9640168 and A9640169 the tyre valve is pointingto the right hand side of the wheel when fitted to Tyre valve, Speed Triple 1050 shown2. HoleWarningWhen the tyre valve is fitted and then removed, the sealon the valve must be replaced. Failure to change theseal may result in tyre pressure loss leading to loss ofmotorcycle control and an edges of the tyre pressure sensor must be parallelto the walls of the wheel well. Damage to the sensormay result if the sensor is not correctly 4 of the sensor to the tyre valve and tighten the fixingof the sensor to 5Nm.

7 Ensure that the sensor is notforced against the walls of the wheel well Sensor2. Tyre valve, Speed Triple 1050 shown3. that the position of the sensor is parallel tothe walls of the wheel well, as shown Sensor2. Fixing10. When secure, the gap between the sensor and thewheel rim must be a minimum of mm and itmust have a limited twist movement around itsfixing. Rectify as Wheel rim2. Sensor11. Refit the tyre noting the following: The tyre lever/install tool must start 30 awayfrom the tyre valve and move away from Position for tyre lever/install tool2.

8 Tyre valve3. Tyre pressure sensor4. Direction of wheel rotation12. Check and, if necessary, adjust the balance of Refit the wheel, as described in the Service mm12T0905T09131430 325 of 6 Note: Read the warning notices printed on the cleaningwipe packet in the Fitting Clean the area of the wheel rim below the tyre valvefor the warning label, as shown Cleaned area, Speed Triple rear wheel shown15. Remove the protective film from the back of thelabel and fit it to the cleaned area of the wheel firm and even pressure to the entire label toensure a good bond is Repeat steps 2 to 15 for the front Pressure Monitoring System (TPMS) ActivationNote: Triumph diagnostic software version 2010_4 orhigher is required to activate the tyre pressuremonitoring system (TPMS).

9 The Triumph diagnostic tool to thediagnostic socket on the to the TPMS diagnostics - the the front and rear TPMS sensoridentification numbers, ensuring the diagnostic toolconfirms that the identification numbers enteredmatch the stored identification numbers after to the Instrument Diagnostics - the desired Market Variation and Units ofPressure, then set Display Tyre Pressure to Yes. Clickon Configure to complete. The tyre pressure displayshould now be available in the information tray onthe instrument display, usually in the fuel informationsection of the the Triumph diagnostic tool from : The tyre pressure monitoring system (TPMS) willnot transmit data until the motorcycle has reachedapproximately 19 mph(30 km/h +/- 10 km/h).

10 The motorcycle at approximately 19 mph (30 km/h +/- 10 km/h) or above to confirm the tyrepressure monitoring system (TPMS) has full operating instructions of the TPMS, itswarnings and instrument read-outs, refer to theOwner's T0907 WarningThe daily check of tyre pressures must not be excludedbecause of the fitment of the TPMS. Check the tyrepressure when the tyres are cold using an accurate tyrepressure gauge (see Owner's Handbook).Use of the TPMS system to set inflation pressures maylead to incorrect tyre pressures leading to loss ofmotorcycle control and an tyre pressure monitoring system is not to be usedas a tyre pressure gauge when adjusting the tyrepressures.