1.5 A max constant current LED driver - st.com

1 July 2008 Rev 21 A max constant current LED driverFeatures Up to 40 V input voltage Less than V voltage overhead Up to A output current PWM dimming pin Shutdown pin LED disconnection diagnostic Slope control with external capApplications LED constant current supplying for varying input voltages Low voltage lighting Small appliances LED lighting Car LED lightsDescriptionThe STCS1A is a BiCMOS constant current source designed to provide a precise constant current starting from a varying input voltage source. The main target is to replace discrete components solution for driving LEDs in low voltage applications such as 5 V, 12 V or 24 V giving benefits in terms of precision, integration and current is set with external resistor up to A with a 10 % precision; a dedicated pin allows implementing PWM dimming.

2 An external capacitor allows setting the slope for the current rise from tens of microseconds to tens of milliseconds allowing reduction of open-drain pin output provides information on load disconnection SO-8 DFN8 (3 x 3 mm) Table summaryOrder codesPackagesPackagingSTCS1 APURDFN8 (3 x 3 mm)3000 parts per reelSTCS1 APHRP ower SO-82500 parts per diagram .. 32 Pin configuration .. 43 Maximum ratings .. 54 Electrical characteristics .. 65 Timing .. 76 Typical performance characteristics .. 87 Detail description .. setting .. Dimming .. 118 Application information.

3 Polarity protection .. considerations .. 129 Package mechanical data .. 1410 Revision history .. 18 STCS1 AApplication diagram3/191 Application diagram Figure application diagram for A LED current to ohmLoad disconnection(Open Drain output)OFFOFFONONPWMENGNDSLOPEVCCDISCFBD RAINRIN100 to ohmLoad disconnection(Open Drain output)OFFOFFONONPWMENGNDSLOPEVCCDISCFBD RAINRIN100 ohmBAT46 ZFILMPin configurationSTCS1A4/192 Pin configuration Figure connections (top view) DFN8 PowerSO-8 Table 2.

4 Pin descriptionPin n SymbolNote1 VCCS upply voltage2 PWMPWM dimming input3 ENShutdown pin4 DRAINI nternal N-MOSFET drain5 FBFeedback input. The control loop regulates the current in such a way that the average voltage at the FB input is 100 mV (nominal). The cathode of the LED and a resistor to ground to set the LED current should be connected at this for slope control8 DISCLoad disconnection flag (open drain)Exp-padInternally connected to ratings5/193 Maximum ratings Note:Absolute maximum ratings are those values beyond which damage to the device may occur. Functional operation under these conditions is not maximum ratingsSymbolParameterValueUnitVCCDC supply to +45 VDRAIND rain to +45 PWM, EN, DISCL ogic to + VCC + , FBConfiguration to + body model (all pins) 2kVTJ (1)1.

5 TJ is calculated from the ambient temperature TA and the power dissipation PD accoring the following formula: TJ = TA + (PD x RthJA). See Figure 16 and Figure 17 for details of max power dissipation for ambient temperatures higher than 25 temperature-40 to 150 CTSTGS torage temperature range-55 to 150 CTable dataSymbolParameterDFN8 Power SO-8 UnitRthJCThermal resistance junction-case1012 C/WRthJAThermal resistance (1)45 (2) C/W1. This value is referred to four-layer PCB, JEDEC standard test With two sides, two planes PCB following EIA/JEDEC JESD51-7 characteristicsSTCS1A6/194 Electrical characteristicsNote:All devices 100 % production tested at TA = 25 C.

6 Limits over the operating temperature range are guaranteed by characteristics (VCC = 12 V; IO = 100 mA; TJ = -40 C to 125 C; VDRAIN = 1 V; CDRAIN = 1 F; CBYP = 100 nF typical values are at TA = 25 C, unless otherwise specified)SymbolParameterTest voltage current range11500mAIOO utput currentRFB = 500mARegulation (percentage with respect to VCC=12V)VCC = to 40 V, IO = 100mA; VDRAIN = 1 V-1+1%VFBF eedback voltageIO = 0 to current (Measured on VCC pin)On Mode450750 AShutdown Mode;VCC = 5 to 12V1 Shutdown Mode;VCC = 12 to 40V3 VDROPD ropout voltage (VDRAIN to GND)IO = 100 = leakage currentShutdown; VDRAIN = 40 V10 ATR/TFRise/Fall time of the current on PWM transitionCSLOPE = 10 nF,TJ = -40 C to 105 C800 sTDDelay on PWM signal (see Figure 1)VPWM rising, VCC = 12 V CSLOPE = floating3 sVPWM falling, VCC = 12 V CSLOPE = level voltageISINK = 5 currentVDISC = 5 V1 ALoad disconnection threshold (VDRAIN-GND) DISC Turn-ON75mVDISC Turn-OFF110 ThermalProtectionShutdown temperature155 CHysteresis25 Logic Inputs (PWM and EN)VLInput low high , PWM leakage current VEN = 5 V.

7 VPWM = 5 V2 AEN input leakage currentVEN = 40 V60 PWM input leakage currentVPWM = 40 V120 STCS1 ATiming7/195 TimingFigure and output current timing PWM10%90%TDTriseTDTfallCurrentPWM10%90%T DTriseTDTfallCurrentFigure diagram High Voltage 45 V+-+-DriverDisc compDISCDRAINFB75 mVEnable,PWM &Slope controllLogicShutdown all blocksThermal ShutdownLow Voltage 45 V100 mVCompLogicVCCENPWMGNDS lope ControlSLOPEHigh Voltage 45 V+-+-+-+-DriverDisc compDISCDRAINFB75 mVEnable,PWM &Slope controllLogicShutdown all blocksThermal ShutdownThermal ShutdownLow Voltage 45 V100 mV100 mVCompLogicVCCENPWMPWMGNDGNDS lope ControlSLOPET ypical performance characteristicsSTCS1A8/196 Typical performance characteristicsFigure vs VCC, TA = 25 CFigure vs RSET Figure vs TemperatureFigure (including VFB) vs temperature Figure vs TemperatureFigure 10.

8 ICC vs VCC STCS1 ATypical performance characteristics9/19 Figure 11. Trise/Tfall vs CSLOPEF igure 12. Turn-on time CSLOPE = floatingFigure 13. Dimming operation: RiseFigure 14. Dimming operation: Fall CSLOPE = 1nF CSLOPE = 1nFDetail descriptionSTCS1A10/197 Detail descriptionThe STCS1A is a BiCMOS constant current source designed to provide a precise constant current starting from a varying input voltage source. The main target is to replace discrete components solution for driving LEDs in low voltage applications such as 5 V, 12 V or 24 V giving benefits in terms of precision, integration and current settingThe current is set with an external sensing resistor connected to the FB pin.

9 The feedback voltage is 100 mV, then a low resistor value can be chosen reducing power dissipation. A value between 1 for instance, should one need a 700 mA LEDs current , RF should be selected according to the following equation: For instance, should one need a 700 mA LEDs current , RF should be selected according to the following equation:RF = VFB / ILEDs = 100 mV / 700 mA = 142 m EnableWhen the enable pin is low the device completely off thus reducing current consumption to less than 1 A. When in shutdown mode, the internal main switch is PWM dimming The PWM input allows implementing PWM dimming on the LED current ; when the PWM input is high the main switch will be on and vice versa.

10 A typical frequency range for the input is from few Hertz to 50 kHz. The maximum dimming frequency is limited by the minimum rise/fall time of the current (obtained with CSLOPE = 0) which is around 4 s each. Above 50 kHz the current waveforms starts assuming a triangular the PWM input is switching, the overall circuitry remains on, this is needed in order to implement two important features: short delay time and controlled slope for the the PWM pin is controlling just the main switch, the overall circuitry is always on and it is able to control the delay time between the PWM input signal and the output current in the range of few s, this is important to implement synchronization among several light LED rise and fall slope of the current is controlled by the CSLOPE capacitor.