469 - GE Grid Solutions

1 IN SERVICESTOPPEDR1 TRIPSETPOINT ACCESSSTARTINGR2 AUXILIARYCOMPUTER RS232 RUNNINGR3 AUXILIARYR4 ALARMR5 BLOCK STARTR6 SERVICEMESSAGEHOT RTDLOSS OF LOAD469 Motor Management Relay PROGRAM PORTSETPOINT78945612 RS485 AUXILIARY RS485 LOCKOUT469 STATUSMOTOR STATUSOUTPUT RELAYSOVERLOAD PICKUPUNBALANCE PICKUPGROUND PICKUP469 MOTOR MANAGEMENT RELAY Instruction Manual469 Firmware Revision: Software Revision: P/N: 1601-0057-DH (GEK-106289J)Copyright 2008 GE MultilinGE Multilin215 Anderson Avenue, Markham, Ontario Canada L6E 1B3 Tel: (905) 294-6222 Fax: (905) 294-8512 Internet: Industrial SystemsIISO9001:2000 GEMULTILINREGISTEREDGE Multilin's Quality Management System is registered to ISO9001:2000 QMI # 005094UL # A3775GE Multilin469 Motor Management Relayi TABLE OF CONTENTS 1.

2 Information .. Specifications .. 1-42.. Withdrawal and Insertion .. Locations .. Wiring Diagram .. Power .. Inputs .. Inputs .. Inputs .. Inputs .. Outputs .. Sensor Connections .. Relays .. Drawout Indicator .. RS485 Communications Ports .. Dielectric Strength .. Two-Speed Motor Wiring .. 2-203. USER FACEPLATE .. Program Port .. 469PC SOFTWARE .. and Communications Configuration .. 469PC .. Capture .. 3-164. Message Map .. , Alarms, and Blocks .. Assignment Practices.

3 S1 469 .. Time Clock .. Messages .. Scratchpad .. Data .. 4-10ii469 Motor Management RelayGE Multilin TABLE OF CONTENTS S2 SYSTEM Sensing .. Communication Control .. Voltage .. S3 DIGITAL .. Status .. Inputs 1 to 4 .. S4 OUTPUT.

4 Reset Mode .. Output S5 THERMAL Thermal Limits .. Model .. Curve Setup .. S6 CURRENT Circuit Trip .. Alarm .. Jam .. Fault .. Differential .. S7 MOTOR Timer .. Block .. Block .. S8 RTD 1 to 7 to 11 .. 12 .. RTD Sensor .. Short/Low Temp .. S9 VOLTAGE Undervoltage .. Overvoltage .. Phase Reversal .. Frequency .. S10 POWER Power Measurement Power Factor .. Reactive Underpower .. Reverse Power .. Torque Setup .. Overtorque Setup .. S11 Trip Counter .. Starter Failure.

5 Current, KW, Kvar, and KVA Demand .. Pulse Output .. S12 ANALOG Analog Outputs 1 to 4 .. Analog Inputs 1 to 4 .. Analog In Diff 1-2 ..4-76GE Multilin469 Motor Management Relayiii TABLE OF CONTENTS Analog In Diff 3-4 .. S13 469 Simulation Mode .. Pre-Fault Setup .. Fault Setup .. Test Output Relays .. Test Analog Output .. Comm Port Monitor .. GEPM Use Only .. S14 TWO-SPEED Description .. Speed 2 O/L Speed 2 Undercurrent .. Speed 2 Acceleration .. 4-855. ACTUAL Values Message.

6 A1 Status .. Trip Blocks .. Inputs .. Time Clock .. A2 METERING Metering .. Metering .. Metering .. Inputs .. A3 LEARNED Motor Maximums .. In Min/Max .. A4 Counters .. Counters .. A5 EVENT 01 to Event 40 .. A6 PRODUCT Model Information .. Information .. Messages .. Messages .. 5-266. MODBUS RTU Protocol .. Frame Format and Data Packet Format .. 6-1iv469 Motor Management RelayGE Multilin TABLE OF CONTENTS.

7 MODBUS Codes 01/02: Read Relay Coil / Digital Input Status .. Codes 03/04: Read Setpoints / Actual Values .. Code 05: Execute Code 06: Store Single Code 07: Read Device Code 08: Loopback Test .. Code 16: Store Multiple Setpoints .. Code 16: Performing Commands .. Error Responses .. MEMORY Map Information .. Memory Map Area .. Recorder .. Memory Map .. Map Format Codes ..6-467. Setup .. HARDWARE FUNCTIONAL Current Accuracy Test .. Input Accuracy Test .. and Differential Accuracy Test .. Multilin 50 Ground Accuracy Accuracy Inputs and Trip Coil Supervision.

8 Inputs and Outputs .. Relays .. ADDITIONAL FUNCTIONAL Curve Measurement Phase Reversal Test .. Circuit Test ..7-12A. APPENDIX TWO-PHASE CT .. COOL TIME of Cool Time Constants .. CURRENT Fault CTs for 50 A CT .. Fault CTs for 5 A Secondary CTs .. A-6B. APPENDIX Declaration of conformity .. B-3GE Multilin469 Motor Management Relay1-11 OVERVIEW11 INTRODUCTION DESCRIPTIONThe 469 Motor Management Relay is a microprocessor based relay designed for the protection and management ofmedium and large horsepower motors and driven equipment.

9 The 469 is equipped with six output relays for trips, alarms,and start blocks. Motor protection, fault diagnostics, power metering, and RTU functions are integrated into one economicaldrawout package. The single-line diagram below illustrates the 469 functionality using ANSI (American National StandardsInstitute) device 1 1: SINGLE LINE DIAGRAMT ypical applications include:Some of the protection highlights are detailed here; a complete list is shown below. Four assignable digital inputs may beconfigured for a number of different features including tachometer or generic trip and alarm with a programmable thermal model incorporates unbalance biasing, RTD feedback, and exponential cooling.

10 In addition to the 15 standardoverload curves, there is a custom curve feature and a curve specifically designed for the starting of high inertia loads, Pumps Fans Compressors Mills Shredders Extruders Debarkers Refiners Cranes Conveyors Chillers Crushers Blowers1-2469 Motor Management RelayGE OVERVIEW1 INTRODUCTION1when the acceleration time exceeds the safe stall time. A second overload curve is provided for two-speed motors. Groundfaults or earth leakage as low as A may be detected using the GE Power Management 50 Ground CT. CT inputsfor phase differential protection are also provided.