7 Sealants - Master Builders Solutions
7 Sealants MasterSeal® SL 2 ™ Multi-component self-leveling polyurethane sealant FORMERLY SONOLASTIC® SL 2 ™ DESCRIPTION MasterSeal SL 2 is a multi-component, self-leveling, elastomeric polyurethane sealant that is mixed and poured in place. When cured, it forms a tough, resilient joint seal that resists penetration and
Tags:
Sealant, Sealmaster, Sealants masterseal
Information
Domain:
Source:
Link to this page:
Please notify us if you found a problem with this document:
Documents from same domain
7 Sealants - Master Builders Solutions
assets.master-builders-solutions.comFORMERLY SONOLASTIC® NP 1™ DESCRIPTION MasterSeal NP 1 is a one-component, high-performance, non-priming, gun-grade, elastomeric polyurethane sealant. It requires no mixing and typically requires no priming to bond to many …
Concrete hardener and dustproofer - Master Builders Solutions
assets.master-builders-solutions.comMasterKure HD 300WB is a magnesium fluorosilicate concrete hardener and dustproofer that ... product data sheet and SDS are being used; call Customer Service (1-800-433-9517) to ... understand and follow all Safety Data Sheets and product label information for this product prior to use. The SDS can be
Sheet, Data, Safety, Data sheet, Safety data, Magnesium, Masterkure
MasterProtect HB 400 - Master Builders Solutions
assets.master-builders-solutions.comMasterProtect HB 400 is meant to be applied as a two-coat system, achieving a total dry-film thickness (DFT) of 12–16 mils (0.3 mm–0.4 mm). For re-coat applications one coat applied at 11–5 mils (0.279–0.127) DFT. 2.Apply MasterProtect HB 400 by brush, spray, roller, or spray-and-backroll. Spray apply
Traffic Coatings MasterSeal M 200 - Master Builders Solutions
assets.master-builders-solutions.com7 Coatings DESCRIPTION MasterSeal M 200 is a one-component, moisture curing polyurethane base coat for use in MasterSeal Traffic 1500 and 2000 deck coating systems. PRODUCT HIGHLIGHTS • MasterSeal M 200 has strong adhesion properties • Easy preparation reduces on-site labor costs • Available in both self-leveling and flash/sloping
MasterProtect H 1000 - Master Builders Solutions
assets.master-builders-solutions.comAir, substrate, and material temperatures should be 20 °F (-7 °C) and rising at the time of the application. Substrate must be frost free. Do not apply sealer when temperatures are expected to fall below 20 °F (-7 °C) within 12 hours or when rain is expected within 4 hours following application. Maximum application temperature is 95 °F (35 ...
MasterSeal TC 225 - Master Builders Solutions
assets.master-builders-solutions.comMasterSeal TC 225 is a moisture-curing polyurethane top coat for use in MasterSeal Traffic 1500 deck coating systems. The MasterSeal TC 225 is a one-component waterproofing coating and is UV-resistant. The ... Read, understand and follow all Material Safety Data Sheets and product label information for this product prior to use. The MSDS can
Dampproofing MasterSeal 610, 614, 615
assets.master-builders-solutions.comand pinholes. Carry coating over exposed top and outside edge of footing. Spread around all joints, grooves, and slots and into all chases, corners, reveals and soffits. Bring the coating to finished grade. 3.Backfilling: Place backfill at least 24–48 hours after application, but within 7 days. Do not rupture or damage the film or displace the
Coatings MasterSeal 350 - Master Builders Solutions
assets.master-builders-solutions.comEPOXY MORTAR 1.Mix the two components of MasterSeal 350 using the recommended procedures under the Mixing section. 2.Slowly add up to five parts by volume of oven-dried sand to one part of mixed epoxy. 3.For larger applications, a paddle-type (mortar) mixer may be used. However, the A and B components must first be mixed together using
Types, Epoxy, Mortars, Sealmaster, Epoxy mortar, Masterseal 350
MasterEmaco T 1060 - Master Builders Solutions
assets.master-builders-solutions.comfor surface prep requirements to permit proper bond. REINFORCING STEEL 1. ... • For professional use only; not for sale to or use ... Master Builders Solutions Construction Systems US, LLC 889 Valley Park Drive, Shakopee, MN 55379 Customer Service +1 (800) 433-9517
MasterEmaco N 425 - Master Builders Solutions
assets.master-builders-solutions.comTechnical Data Composition MasterEmaco N 425 is composed of crystalline (quartz) silica and Portland cement. Compressive strength, psi (MPa) ASTM C 109, modified* 1 day 2,150 (14.8) 7 days 5,600 (38.6) 28 days 6,750 (46.5)
Related documents
WATERPROOFING SikaSwell® HYDROPHILIC PROFILES AND …
www.sikawaterproofing.co.ukThe SikaSwell® profiles and sealants are applied to a sound and clean substrate, free of grease, dust and loose particles. Due to the direct application on the finished surface this waterproofing joint sealing system has no influence on the reinforcement and formwork. The application should take place shortly before concreting to
Alumina Trihydrate (ATH)
www.hubermaterials.comadhesives, caulks and sealants applications. Because ATH is an inert functional pigment available in a wide array of particle size distributions, it offers a number of key features and benefits: Features Benefits Dehydration at 428°F Flame retardance (220°C) Smoke suppression
All Purpose Silicone 1* Sealant - GE Sealants | Home
gesealants.com(such as moisture/frost, oils, old sealants, soaps and other surface treatments, etc.) must be removed from the surfaces to which the sealant is intended to adhere. • For cleaning, a solvent-dampened clean rag usually produces the desired result. Isopropyl Alcohol (IPA) is a commonly used solvent and has
Pedestrian and Waterproofing System - Tremco Sealants
www.tremcosealants.comRecoatable and compatible with other Tremco sealants, which enhances waterproofing protection with full system compatibility. Availability Immediately available from your local Tremco Sales Representative, Tremco distributor, or warehouse. Packaging Vulkem 350: 5-gal (18.9-L) pails, 55-gal (208.2-L) drums
GLAZING PROCEDURES - Tremco Sealants
www.tremcosealants.comProper use of Tremco glazing materials including sealants, gaskets, tapes and setting blocks. Proper tensile bead location. Structural tensile beads are normally located on the interior face of the lite or panel (#2 or #4 surface) with bonding to a structurally sound substrate such as a