AVR040: EMC Design Considerations

1 AVR 8-bit microcontrollers AVR040: EMC Design Considerations APPLICATION NOTES copeThis application note covers the most common EMC problems designersencounter when using microcontrollers . It will briefly discuss the variousphenomena. The reference literature covers EMC Design in more detail, andfor designers who are going to build products that need to be EMCcompliant, further study is highly recommended. A good EMC designrequires more knowledge than what can be put into a short application many other Design issues, EMC is not an area where it is possible tolist a set of rules.

2 EMC compliance cannot be guaranteed by Design ; it has tobe is recommended that readers unfamiliar with EMC Design read thisdocument more than once, as some of the subjects described early in thisdocument are more easily understood if the reader has already read the restof the Note-11/2016 Table of Phenomena and EMC (Immunity Test).. Transient Burst (Immunity Test).. Immunity Emission Immunity with EMC the Noise Path to and Supply, Power Routing, and Decoupling Layout and Loops and Signal I/O Pin Pin AVR040: EMC Design Considerations [APPLICATION NOTE]Atmel-1619E-EMC- Design -Consideratio ns_AVR040_Application Note-11/201621.

3 IntroductionElectromagnetic compatibility is a subject most designers did not have to worry about a few years , every designer putting a product on the global market has to consider this. There are two mainreasons for this: The electromagnetic environment is getting tougherHigh-frequency radio transmitters, like mobile telephones, are found everywhere. More and moresystems are using switching power supplies in the power circuit, and the overall number ofelectronic appliances is increasing every year. Electronic circuits are becoming more and more sensitivePower supply voltages are decreasing, reducing the noise margin of input pins.

4 Circuit geometriesget smaller and smaller, reducing the amount of energy required to change a logic level, and at thesame time reducing the amount of noise required to alter the logic values of a designer's point of view, EMC phenomena have to be considered in two different ways: How the environment may affect the Design (immunity). How the Design may affect the environment (emission).Traditionally, the only government regulations have been on the emission side: An electronic device is notallowed to emit more than a certain amount of radio frequency energy to avoid disturbing radiocommunication or operation of other electronic equipment.

5 Most countries in the world have regulationson this demands on noise immunity earlier were found only for special applications, like medicalequipment, avionics and military 1995, Europe introduced regulations on immunity for all electronic products, known as the EMCdirective. The purpose of this directive is: To ensure that no product emits or radiates any disturbances that may interfere with the function ofother equipment. To ensure that all products withstand the disturbances present in their operating the same time, enforcement of EMC requirements was strengthened: every product made in orimported to Europe must prove to fulfill both emission and immunity requirements before it can be put onthe in other parts of the world also introduce similar legal limits for acceptable emission and immunity levels for different product classes and environments aregiven in various international standards.

6 A more detailed description of these is found in the EMC directive applies to finished products, but not to components. As a component will not workwithout being put into a system, the demands are put on the finished system. How the problems aresolved internally is left to the a result of this, the test procedures required for CE-marking are well suited for testing finishedproducts, but they cannot be used directly for testing components like microcontrollers . The same appliesfor the test procedures required for FCC approval. The test boards the components are mounted onduring test will influence EMC test data for components.

7 These results should therefore only be regardedas the other hand, there are test standards (military, automotive, and others) that are made to testcomponents directly. These standards specify standardized test boards to make sure that measurementsAtmel AVR040: EMC Design Considerations [APPLICATION NOTE]Atmel-1619E-EMC- Design -Consideratio ns_AVR040_Application Note-11/20163on different manufacturer's components can be compared. These tests are not a requirement accordingto the EMC AVR040: EMC Design Considerations [APPLICATION NOTE]Atmel-1619E-EMC- Design -Consideratio ns_AVR040_Application Note-11/201642.

8 EMC Phenomena and EMC TestingUnlike many other Design issues (for instance, power calculations), there are no exact rules for EMCdesign saying, Do it like this and it will work. Instead, there are a lot of Design suggestions saying, Do itlike this and it may work, or This is more likely to work, but at a higher cost. For most applications, it is not possible to prove EMC compliance without actual lab testing. Several newCAD packages include EMC simulations. These may be good Design help, saving some extra trips to thetest lab, but they cannot replace the final compliance chapter will give a short introduction to the most common EMC phenomena encountered in MCUsystem designs.

9 To make it easier to understand the different phenomena, the phenomena and the testsused to emulate them are described ESD (Immunity Test)ESD (electrostatic discharge) is a phenomenon most people have experienced. This is what happens ifyou feel a small electric shock when you touch your kitchen sink or another grounded object. Whathappens is that your body has been charged with a small electrostatic charge (easily achieved by walkingon synthetic fiber carpets). This charge is released when you touch an object with a different charge or anobject connected to ground.

10 For a human being to actually feel the discharge, the voltage must be about4kV or more, and it is not difficult to achieve tens of 2-1. ESD Test GeneratorRcRdCsVsTo Discharge TipTo Ground ReturnSA simple way of modeling this phenomenon is to use a capacitor that will hold the same charge as thebody and a series resistor that will release this charge the same way the body figure above shows a principle schematic of this setup. CS is the storage capacitor that equals thecapacitance of the human body, RD is the discharge resistance that equals the resistance of the humanbody.