CX-Protocol Operation Manual - Omron

1 Cat. No. W344-E1-11CX- protocol Ver. MANUALSYSMACWS02-PSTC1-ECX- protocol Ver. ManualRevised December 2009ivvNotice: Omron products are manufactured for use according to proper procedures by a qualified operatorand only for the purposes described in this following conventions are used to indicate and classify precautions in this Manual . Always heedthe information provided with them. Failure to heed precautions can result in injury to people or dam-age to the product.!DANGERI ndicates information that, if not heeded, is likely to result in loss of life or serious , there may be severe property damage.!WARNINGI ndicates information that, if not heeded, could possibly result in loss of life or seriousinjury. Additionally, there may be severe property damage.!CautionIndicates information that, if not heeded, could result in relatively serious or minor injury,damage to the product, or faulty Product ReferencesAll Omron products are capitalized in this Manual .

2 The word Unit is also capitalized when it refers toan Omron product, regardless of whether or not it appears in the proper name of the abbreviation Ch, which appears in some displays and on some Omron products, often means word and is abbreviated Wd in documentation in this abbreviation PLC means Programmable Controller and the abbreviation PC means personalcomputer and are not used as abbreviations for anything abbreviation PMSU means protocol Macro Support Unit and refers to the CommunicationsBoard for the C200HX/HG/HE, Serial Communications Board for the CS, and Serial CommunicationsUnits for the AidsThe following headings appear in the left column of the Manual to help you locate different types information of particular interest for efficient and convenient opera-tion of the ,2, Indicates lists of one sort or another, such as procedures, checklists, etc. Omron , 2008 All rights reserved. No part of this publication may be reproduced, stored in a retrieval system, or transmitted, in any form, or by any means, mechanical, electronic, photocopying, recording, or otherwise, without the prior written permission of patent liability is assumed with respect to the use of the information contained herein.

3 Moreover, because Omron is constantly striving to improve its high-quality products, the information contained in this Manual is subject to change withoutnotice. Every precaution has been taken in the preparation of this Manual . Nevertheless, Omron assumes no responsibilityfor errors or omissions. Neither is any liability assumed for damages resulting from the use of the information contained in this publication. viviiTABLE OF CONTENTSPRECAUTIONS .. xxiii1 Intended Audience ..xxiv2 General Precautions ..xxiv3 Safety Precautions ..xxiv4 Operating Environment Precautions ..xxiv5 Application Precautions ..xxv6 Software Operating Procedures..xxviSECTION 1 Introduction .. 11-1 Overview of the CX-Protocol ..21-2 Features ..21-3 Checking the Contents of the Package ..51-4 Supported PLC Models and Personal Computers ..51-5 System Configuration ..91-6 protocol Macro ..131-7 protocol Macro Structure ..161-8 Data Created by the CX-Protocol ..191-9 Main Screens of the CX-Protocol .

4 201-10 Overview of Project Creation ..231-11 Incorporated Standard System protocol ..241-12 Basic Procedure of the protocol Macro Usage ..251-13 Specifications ..321-14 Differences between protocol Macros ..36 SECTION 2 Installing/Uninstalling/Starting/Ending .. 392-1 Connecting to a PLC ..402-2 Installing and Uninstalling the Software..422-3 Uninstalling Software ..492-4 Startup ..522-5 Shutdown..532-6 Outline of User Interface..54 SECTION 3 protocol Macro .. 653-1 protocol Macro Outline..663-2 Sequence Attributes (Common to All Steps) ..833-3 Step Attributes..923-4 Communication Message Attributes ..1033-5 Creating Matrices ..1203-6 Examples of Standard System Protocols ..1243-7 Example of Communications Sequence ..1263-8 Executing a Created Communications Sequence (CS/CJ) ..1293-9 Executing a Created Communications Sequence (C200HX/HG/HE) ..1363-10 Auxiliary Area and Allocated Data Areas ..142viiiTABLE OF CONTENTSSECTION 4 Using the protocol Macro Function.

5 1594-1 Applicable Range of the protocol Macro Function.. 1604-2 protocol Creation Process .. 1624-3 Transmission Control Mode Setup .. 1654-4 Ladder Programming Method .. 1684-5 Calculation Method of Monitoring Time.. 1794-6 Operation Confirmation .. 1814-7 Errors at the protocol Execution .. 1834-8 Communications Response Time Performance .. 1924-9 Cycle Time Performance .. 209 SECTION 5 Object Creation .. 2115-1 Creating Projects and Protocols.. 2125-2 Creating Sequences and Steps .. 2165-3 Creating Messages and Matrices .. 2175-4 System protocol Display and Editing .. 219 SECTION 6 Project and protocol Editing .. 2216-1 Editing Projects .. 2226-2 Editing Protocols .. 224 SECTION 7 Sequence Setting and Editing .. 2277-1 Setting Sequences .. 2287-2 Editing Sequences .. 234 SECTION 8 Step Setting and Editing .. 2378-1 Step Setting .. 2388-2 Step Editing .. 244 SECTION 9 Setting and Editing Messages and Matrix Lists .. 2479-1 Creating Messages .. 2489-2 Matrix Creation.

6 2629-3 Message and Matrix Editing .. 263 SECTION 10 Communications PLC Setup and Online Connections . 26710-1 PLC System Configuration .. 26810-2 Communications Settings between Personal Computer and PLC .. 26910-3 Online Connections and Mode Changes .. 27610-4 Modem Connections .. 27810-5 I/O Table Creation .. 28710-6 PMSU Communications Port Settings .. 28810-7 Transfer of Communications Port Setting Data to PLC .. 290ixTABLE OF CONTENTSSECTION 11 protocol Data Transferring and Printing .. 29311-1 Transferring and Reading protocol Data between the Computer and PMSU ..29411-2 Printing Protocols ..29911-3 Importing protocol Data from PST/PSS Files ..30111-4 CS/CJ protocol and C200HX/HG/HE protocol ..303 SECTION 12 Tracing and Monitoring .. 30512-1 Tracing Transmission Lines ..30612-2 Outline of PLC Memory Window..31012-3 I/O Memory Display and Editing ..31712-4 I/O Memory Monitor ..32012-5 I/O Memory Transfer and Comparison.

7 325 SECTION 13 Error and Error Log Display.. 329 SECTION 14 Troubleshooting .. 337 SECTION 15 Help .. 345 AppendicesACreating the protocol Applications ..349 BPLC Setup and PMSU Settings ..363 CWiring RS-232C Cable Connectors ..369 Revision History .. 373xTABLE OF CONTENTSxiAbout this Manual :The CX-Protocol is Support Software for the protocol macro functionality of Windows 95, Windows 98,Windows 98SE, Windows Me, Windows NT (SP6a), Windows 2000 (SP2 or higher), Windows XP, andWindows Vista. This Manual describes the installation and Operation of the CX-Protocol and includesthe sections described below. This Manual is intended for the following personnel:Personnel in charge of installing FA devicesPersonnel designing FA systemsPersonnel managing FA facilitiesNameCat. WS02-PSTC1-ECX- protocol Operation Manual W344(this Manual )Describes the use of the CX-Protocol to create protocol macros as communications sequences to communicate with external devices. (This Manual )CX-One Setup Manual CXONE-AL@@C-V4/AL@@D-V4W463 Installation and overview of CX-One FA Integrated Tool CS/CJ Series CS1W-SCB@1-V1, CS1W-SCU@1-V1CJ1W-SCU@1-V1, CJ1W-SCU@2 Serial Communications Boards and Serial Communications Unit Operation ManualW336 Describes the use of Serial Communications Unit and Boards to perform serial communications with external devices, including the usage of standard system protocols for Omron CS/CJ/CP/NSJ Series CS1G/H-CPU@@HCS1G/H-CPU@@-EV1 CS1D-CPU@@HCS1D-CPU@@SCS1W-SCU@@-V1CS1W- SCB@@-V1CJ2H-CPU6@-EIPCJ2H-CPU6@CJ1H-CPU @@H-RCJ1G/H-CPU@@HCJ1G-CPU@@PCJ1G-CPU@@C J1M-CPU@@CJ1W-SCU@@-V1CP1H-X@@@@-@CP1H-X A@@@@-@CP1H-Y@@@@-@NSJ@-@@@@(B)-G5 DNSJ@-@@@@(B)-M3 DCommunications Commands Reference ManualW342 Describes the C-series (Host Link)

8 And FINS communications commands used with CS/CJ/CP-series PLCs and NSJ-series CJ SeriesCJ2H-CPU6@-EIPCJ2H-CPU6@Programmab le ControllersHardware User's ManualW472 Provides an outline of and describes the design, installation, maintenance, and other basic operations for the CJ-series CJ2 CPU following information is included:Overview and featuresSystem configurationInstallation and wiringTroubleshootingUse this Manual together with the CJ SeriesCJ2H-CPU6@-EIPCJ2H-CPU6@Programmab le ControllersSoftware User's ManualW473 Describes programming and other methods to use the functions of the CJ2 CPU following information is included:CPU Unit operationInternal memory areasProgrammingTa s k sCPU Unit built-in functionsUse this Manual together with the CS Series CS1G/H-CPU@@HCS1G/H-CPU@@-EV1 Programmable Controllers Operation ManualW339 Describes the installation and Operation of the CS-series CJ Series CJ1H-CPU@@H-R, CJ1G/H-CPU@@H, CJ1G-CPU@@P, CJ1G-CPU@@, CJ1M-CPU@@Programmable Controllers Operation ManualW393 Describes the installation and Operation of the CJ-series CS/CJ/NSJ Series CS1G/H-CPU@@H, CS1G/H-CPU@@-EV1, CS1D-CPU@@H, CS1D-CPU@@S, CJ1H-CPU@@H-R, CJ1G/H-CPU@@H, CJ1G-CPU@@P, C J 1 G - C P U@@, CJ1M-CPU@@, NSJ@-@@@@(B)-G5 DNSJ@-@@@@(B)-M3 DProgrammable Controllers Programming ManualW394 Describes programming and other methods to use the functions of the CS/CJ/NSJ-series following information is included: Programming Tasks File memory Other functionsUse this Manual in combination with the SYSMAC CS Series Operation Manual (W339) or SYSMAC CJ Series Operation Manual (W393).

9 SYSMAC CS/CJ SeriesCS1G/H-CPU@@-EV1, CS1G/H-CPU@@H, CS1D-CPU@@H, CS1D-CPU@@S,CJ2H-CPU6@-EIP, CJ2H-CPU6@, CJ1H-CPU@@H-RCJ1G-CPU@@, CJ1G/H-CPU@@H,CJ1G-CPU@@P, C J 1 M - C P U@@SYSMAC One NSJ SeriesNSJ@-@@@@(B)-G5 DNSJ@-@@@@(B)-M3 DProgrammable ControllersInstructions Reference ManualW474 Describes the ladder diagram programming instructions sup-ported by CS/CJ-series or NSJ-series programming, use this Manual together with the Opera-tion Manual or Hardware User's Manual (CS1: W339, CJ1: W393,or CJ2:W472) and Programming Manual or Software User's Manual (CS1/CJ1:W394 or CJ2:W473).SYSMAC CP Series CP1H-X@@@@-@CP1H-XA@@@@-@CP1H-Y@@@@-@CP1 H CPU Unit Operation ManualW450 Provides the following information on the CP Series: Overview/Features System configuration Mounting and wiring I/O memory allocation TroubleshootingUse this Manual together with the CP1H Programmable Control-lers Programming Manual (W451). NSJ SeriesNSJ5-TQ@@(B)-G5D, NSJ5-SQ@@(B)-G5D, NSJ8-TV@@(B)-G5D, NSJ10-TV@@(B)-G5D, NSJ12-TS@@(B)-G5D, NSJ5-TQ@@(B)-M3D, NSJ5-SQ@@(B)-M3D, NSJ8-TV@@(B)-M3D, NSJW-ETN21, NSJW-CLK21-V1, NSJW-IC101 Operation ManualW452 Provides the following information about the NSJ-series NSJ Controllers:Overview and featuresDesigning the system configurationInstallation and wiringI/O memory allocationsTroubleshooting and maintenanceUse this Manual in combination with the following manuals.

10 SYSMAC CS Series Operation Manual (W339), SYSMAC CJ Series Operation Manual (W393), SYSMAC CS/CJ Series Pro-gramming Manual (W394), and NS-V1/-V2 Series Setup Manual (V083)SYSMAC WS02-CXPC1-V9CX-Programmer Operation ManualW446 Provides information on how to use the CX-Programmer, a pro-gramming device that supports the CS/CJ-series PLCs, and the CX-Net contained within CS/CJ Series CQM1H-PRO-E1C200H-PRO27-E, CQM1-PRO01-EProgramming Consoles Operation Manual W341 Provides information on how to program and operate CS/CJ-series PLCs using a Programming Console.!WARNINGF ailure to read and understand the information provided in this Manual may result in per-sonal injury or death, damage to the product, or product failure. Please read each sectionin its entirety and be sure you understand the information provided in the section andrelated sections before attempting any of the procedures or operations read this Manual carefully and be sure you understand the information provided beforeattempting to install and/or operate the CX-Protocol .