Example: air traffic controller

FOAMULAR Extruded Polystyrene Insulation

Product Data SheetThere s a type and size of FOAMULAR Insulation for every applicationApplications Masonry cavity walls Wall furring to interior masonry/concrete walls Masonry veneer/steel stud wall systems Tilt-up concrete panels Below-grade exterior foundations Poured-in-place concrete wall systems Precast concrete Under concrete slabs Plaza and parking decks Commercial roofi ng systems Recover board Cold storage facilities Below-grade waterproofi ng Frost heave protection Agricultural housing RV/mobile homes Exterior Insulation and fi nishing systems Insulating sheathingAlso Available FoamSealR sill plate gasket raft-R-mate attic rafter vents FANFOLD foundation protection board BILD-R-TAPE construction tapeProduct DataMaterial: Extruded Polystyrene closed-cell foam panel with continuous skin on face and back surface. FOAMULAR Insulation is produced by Owens Corning s patented Hydrovac process technology under conditions of strict quality in units (typically 3,072 board-feet per unit) with two stretch-wrap bands per Although it does contain a fl ame-retardant additive to inhibit ignition from small fi re sources, if exposed to fi re of suffi cient heat and intensity, FOAMULAR Insulation will ignite.

Product Data Sheet There’s a type and size of FOAMULAR insulation for every application Applications • Masonry cavity walls • Wall furring to interior

Tags:

  Polystyrene, Insulation, Foamular, Extruded, Foamular extruded polystyrene insulation

Information

Domain:

Source:

Link to this page:

Please notify us if you found a problem with this document:

Other abuse

Transcription of FOAMULAR Extruded Polystyrene Insulation

1 Product Data SheetThere s a type and size of FOAMULAR Insulation for every applicationApplications Masonry cavity walls Wall furring to interior masonry/concrete walls Masonry veneer/steel stud wall systems Tilt-up concrete panels Below-grade exterior foundations Poured-in-place concrete wall systems Precast concrete Under concrete slabs Plaza and parking decks Commercial roofi ng systems Recover board Cold storage facilities Below-grade waterproofi ng Frost heave protection Agricultural housing RV/mobile homes Exterior Insulation and fi nishing systems Insulating sheathingAlso Available FoamSealR sill plate gasket raft-R-mate attic rafter vents FANFOLD foundation protection board BILD-R-TAPE construction tapeProduct DataMaterial: Extruded Polystyrene closed-cell foam panel with continuous skin on face and back surface. FOAMULAR Insulation is produced by Owens Corning s patented Hydrovac process technology under conditions of strict quality in units (typically 3,072 board-feet per unit) with two stretch-wrap bands per Although it does contain a fl ame-retardant additive to inhibit ignition from small fi re sources, if exposed to fi re of suffi cient heat and intensity, FOAMULAR Insulation will ignite.

2 Do not expose the product to open fl ame during shipping, storage, installation or use. In most applications, a code-compliant thermal barrier must be used to separate FOAMULAR Insulation from the building interior. See conditions for use section of ICC ES Reprt 96-24 for application covering recom-mendations. FOAMULAR Extruded Polystyrene Insulation Commercial Product Directory of Availability and Physical PropertiesProduct AvailabilityInsulation ProductThickness1 (in)Width x Length2 (in)EdgesWeight (approx. lb/1,000 ft2 for 1 thickness) FOAMULAR 150(15 psi)31, 1 , 2, 2 , 31, 1 , 2, 2 , 3, 3 1, 1 , 2, 2 , 3116 x 9624 x 9648 x 9648 x 108 Square120-130 FOAMULAR 150(15 psi)31, 1 , 2, 2 , 348 x 96 Scored SquareFOAMULAR 150(15 psi)31, 1 , 21, 1 , 2124 x 9648 x 9648 x 108T&G4 FOAMULAR 250(25 psi)31, 1 , 2, 2 , 3 , 1, 1 , 2, 2 , 3, 3 , 4 , 1, 1 , 2, 2 , 3 , 116 x 9624 x 9648 x 9648 x 108 Square150 FOAMULAR 250(25 psi)3 , 1, 1 , 2, 2 , 348 x 96 Scored SquareFOAMULAR 250(25 psi)3 , 1, 1 , 2 , 1, 1 , 2 , 124 x 9648 x 9648 x 108T&G4 FOAMULAR 400(40 psi)31 , 2, 2 , 3, 3 , 424 x 96 Square200 FOAMULAR 600(60 psi)31 , 2, 2 , 324 x 96 Square240 FOAMULAR Half-inch(18 psi)3 24 x 96, 48 x 96 or 108 Square150 AGTEK 1, 1 48 x 200-318 Ship-lap150 DURAPINK , , 148 x 96 Square150 INSUL-DRAIN 1, 1 , 2 48 x 96T&G4165 THERMAPINK 181, 1 , 2, 348 x 96 Square1501 R per inch: (at 75 F mean temperature).

3 Nominal fi lm-faced insulating sheathing @ 75 F mean temperature2 Other sizes available on request. Consult your local Owens Corning representative for strength, minimum (specifi cation) value (lb/in2)4 Tongue-and-groove edge reduces air infi : All products in every size described here may not be available in all geographic markets. For information about non-standard products, consult a local sales offi ce or Data SheetGrinding, sawing or fabricating can produce dust particles which may be irritating to eyes, nose and throat. Avoid buildup of dusts. Certain conditions form explosive dust atmospheres that can be ignited. Ensure adequate ventilation. When installing the THERMAPINK Insulation in the steel deck roof assemblies, see special instructions for installation directly over the steel decking. During shipping, storage, installation and use, this product should not be exposed to open fl ame of other ignition sources. See other FOAMULAR installation literature for more detailed product and application Physical ProperitesProduct/ValuesPropertyTe st Method2 FOAMULAR 150 FOAMULAR 250 FOAMULAR 400 FOAMULAR 600 FOAMULARHalf-inchAGTEKDURAPINK INSUL-DRAINTHERMAPINK18 Thermal conductivity - k (Btu x in/hr x ft2 x F, max)3@ 75 F mean temperature@ 40 F mean temperatureASTM C Strength, minimum value (lb/in2)4 ASTM D Strength (lb/in2, min.)

4 5 ASTM C 2036075115140 75757560 Water Absorption (% by volume, max.)6 ASTM C Vapor Permeance (perm, max.)7 ASTM E Affi nity hydrophobic Water Capillarity none Dimensional Stability (% linear change, max.)8 ASTM D Coeffi cient of Thermal Expansion (in/in/ F, max) x 10-5 x 10-5 x 10-5 x 10-5 x 10-5 x 10-5 x 10-5 x 10-5 x 10-5 Flame Spread9,10 ASTM E 84555555555 Smoke Developed9,10,11 ASTM E 8445-17545-17545-17545-17545-17545-17545 -17545-17545-175 Oxygen index, D 2863242424242424242424 Type Classifi cationsASTM C 578 Type XType IVType VIType VII Type IVType IVType IVType X1 Properties shown are representative values for 1 thick material based upon most recent product quality audit ed as required to meet ASTM Resistance (R) (hr x ft2 x F/Btu) of a 1 thickness (at 75 F mean temperature), (at 40 F mean temperature). 4 Value at yield or 10%, whichever occurs fi at 5% yield or 5% whichever occurs fi ranges from to value shown, due to the level of precision of the test water vapor permeance data decreases as thickness ranges from to value laboratory tests are not intended to describe the hazard presented by this material under actual fi re from Underwriters Laboratories, Inc.

5 Classifi ed. See Classifi cation Certifi cate E 84 is thickness-dependent, therefore a range of values is given.*Minimum foam core valueFOAMULAR Extruded Polystyrene Insulation Commercial Product Directory of Availability and Physical PropertiesOWENS CORNING FOAM Insulation , LLCONE OWENS CORNING PARKWAYTOLEDO, OHIO, USA 436591-800-GET-PINK No. 23542-C. Printed in January 2007. THE PINK PANTHER & 1964 2007 Metro-Goldwyn-Mayer Studios Inc. All Rights Reserved. The color PINK is a registered trademark of Owens Corning. 2007 Owens Corning.


Related search queries