Example: marketing

Handloader's Guide - PDF.TEXTFILES.COM

Handloader's GuideFor Smokeless PowdersShotshell Rifle HandgunBefore using any of the loading data contained in this Guide ,please be sure to read all of the safety information. 2 SAFETY INFORMATIONThis IMR Handloader's Guide presents revised and updated infor-mation on the use of IMR powders to reload shotshell, handgun andrifle ammunition. This Guide is not intended to be a "how to" manualfor reloading, and we strongly recommend that all handloaderscarefully read one or more of the reloading manuals which cover thesubject in detail. This Guide is offered to be used at your owndiscretion and risk. Since we have no control over the circum-stances of use, we assume no liability for the results obtained. Andwe guarantee only that our powders meet our manufacturing is possible that changes in components which could affect ballis-tic performance could occur without our knowledge.

14. Observe all maximum load warnings in handbooks. 15. Work up all new loads starting 10% below the recommended maximum charge weight. 16. Examine every case before loading to insure it is in good condition. 17. Watch for indications of high pressures in establishing a new load. 18. Never use smokeless powder in firearms designed for black ...

Tags:

  Handbook

Information

Domain:

Source:

Link to this page:

Please notify us if you found a problem with this document:

Other abuse

Transcription of Handloader's Guide - PDF.TEXTFILES.COM

1 Handloader's GuideFor Smokeless PowdersShotshell Rifle HandgunBefore using any of the loading data contained in this Guide ,please be sure to read all of the safety information. 2 SAFETY INFORMATIONThis IMR Handloader's Guide presents revised and updated infor-mation on the use of IMR powders to reload shotshell, handgun andrifle ammunition. This Guide is not intended to be a "how to" manualfor reloading, and we strongly recommend that all handloaderscarefully read one or more of the reloading manuals which cover thesubject in detail. This Guide is offered to be used at your owndiscretion and risk. Since we have no control over the circum-stances of use, we assume no liability for the results obtained. Andwe guarantee only that our powders meet our manufacturing is possible that changes in components which could affect ballis-tic performance could occur without our knowledge.

2 The compo-nents used and specified in all our data were those that were com-mercially available to the handloader at the time our tests wereconducted. It is the responsibility of the handloader to check each ofhis components to insure that they are the same as specified in modifications and/or alterations can render any type offirearm unsafe. All work should be conducted by the manufactureror a qualified gunsmith. It is highly recommended that a shooterhave his guns checked periodically by a qualified gunsmith to in-sure that they are in safe operating condition. Treat all guns as beingloaded and read and practice all the rules of safe gun handling future of handloading is dependent upon the safe handling andstorage of powder and primers and the safe use of all this regard, read and follow the recommendations of the SportingArms and Ammunition Manufacturers' Institute, Inc.

3 As publishedin "Properties and Storage of Smokeless Powder." A copy of thispamphlet is bound into this Handloader's shotshell data section offers a wide selection of target and fieldloads. There have been a number of changes and modifications inshotshell components which make it increasingly important that thehandloader carefully check all of the components being used toinsure that they are the same as shown. If you have reason to ques-tion any of your components, contact the goal in developing this shotshell data was to offer a selection of"factory duplication" loads, specifying the average velocity and cham-ber pressure of the rounds tested. However, not all factory loads canbe duplicated because the components utilized are not available tothe handloader. All of the ballistics data specified were obtainedusing once-fired cases and components available to the handloadersat the time our tests were of the shotshell data presented were developed using lead not attempt to reload any of the loads listed using steel steel shot in any load developed for lead shot could bevery obtain a reasonable duplication of the ballistic results listed,you must reload exactly as shown.

4 Substitution of componentsespecially primers and/or alteration in powder charge or type ofpowder could result in extremely dangerous , uniform, efficient reloads result only from careful reloadingprocedures. Always check powder and shot weights on a reliablescale, use the exact components specified, seat wads properly anduse only cases that are in good condition. Never leave to chance thepowder type and/or weight and the lead shot weight that you areloading in a shell. Inspect all reloaded shells to insure that crimpclosely duplicates that of factory , time and space do not permit publication of loadsutilizing all of the many components available. Loading data utiliz-ing IMR powders for wads not listed in this Guide may be obtainedby contacting the wad rifle data section contains data for most of the popular car-tridges. The components specified were those that were commer-cially available to the handloader at the time the tests were powder charge weights specified represent loads that devel-oped Maximum Allowable Chamber Pressures with the test bar-rels used and components specified, with the exception of loads thatare specified as (C) compressed charges which may represent casecapacity rather than maximum chamber pressure.

5 All tests wereconducted utilizing commercial barrels in a Universal is not unusual for reloads assembled with particular componentsand fired in the individual reloader's gun to give ballistic results(particularly chamber pressures) that vary in either direction fromthe published data. To compensate for any component and/or guncombination that would tend to yield pressures in excess of thepublished data, it is recommended that the powder charge be re-duced 10% initially. (This reduction in powder charge weight shouldalso be made each time that any of the components in the load arechanged.) After firing several loads at the lower powder chargeweight without ANY evidence of excessive chamber pressure the powder charge weight may then be increased in grain incre-ments as accuracy needs and pressure indications permit. The sub-ject of excessive pressure along with illustrations is included inmost reloading manuals, and should be read before attempting make certain that you use the correct ammunition in data must be used only with IMR Smokeless Powders.

6 Neveruse this data for powders that may have similar numerical desig-nations!HANDGUNThe handgun section contains loads for the more popular handguncartridges utilizing the handloading components commercially avail-able at the time our tests were conducted. We have also included asection of handgun data for the T/C Contender in cartridge andcomponent combinations of particular interest to the metallic sil-houette shooter. Test components used are specified and these exactcomponents must be used to achieve a reasonable duplication of theballistic data powder charge weights specified represent loads that devel-oped Maximum Allowable Chamber Pressures with the test bar-rels and components used, with the exception of loads that arespecified as (C) compressed charges and therefore may representcase capacity rather than maximum chamber pressure, and loadsthat duplicate factory velocity.

7 All tests were conducted utilizingcommercial barrels in a Universal practice all of the principals of SAFE RELOADING and enjoygood : It should be recognized that Auto-Loading Shotguns may not function with some of the Low ChamberPressure Loads. Several Handgun Calibers show Chamber Pressure in PSI. If you use Military Brass for certain Center-Fire Calibers the maximum powder charges should belowered from data shown. We have included a separate section in the Rifle Data Section that provides recommendations forvarious Calibers and Components showing Chamber Pressures in PSI units versus prior data withCUP units for the Chamber Pressure. There will be additions to this section as the data OF CONTENTSPageSHOTSHELL TARGET .. 412 gauge target, 24 gram .. 412 gauge target, 1 oz.. 1212 gauge target, 1 1/8 oz.. 1820 gauge target .. 2928 gauge target .. bore target .. 34 SHOTSHELL FIELD.

8 3410 gauge field .. 3412 gauge buckshot .. 35 Page12 gauge field .. 3516 gauge field .. 4220 gauge field .. bore field .. 46 Table of Abbreviations .. 46 Powder Table .. 46 Chilled Shot Table .. 46 RIFLE - CUP DATA .. 47 Weatherby Cartridges .. 51 RIFLE - PSI DATA .. 54T/C Contender .. 57 Powder Selection Guide .. 59 RELOADING SAFETYR eloading ammunition is an enjoyable hobby, and can be conducted safely if certain rules are followed:1. Exercise care and common sense at all Don't become distracted when you are Never load in haste. A careless mistake can be equipment as manufacturer take Store powder in a cool, dry place at all Never use a powder unless you are positive of its Never substitute smokeless powder for black Never use IMR powder data for any other powder typeswith similar numerical Keep powder away from heat and open Never smoke while handling Keep powder out of reach of Don't mix Don't keep more powder in an open container thanyou Observe all maximum load warnings in Work up all new loads starting 10% below therecommended maximum charge Examine every case before loading to insure it is in Watch for indications of high pressures in establishing anew Never use smokeless powder in firearms designed forblack DO NOT use steel shot in any of the shotshell loads listedin this Use of safety glasses while reloading is Clean up any powder spills immediately.

9 Use dust pan andbrush to clean up powder. Dispose of it in accordancewith recommended Make sure powder container is empty before disposing Consult suppliers of components if you have anyquestions about their Check powder charges regularly to insure using properpowder charge Develop a routine for reloading to guard against : FEDERAL PLASTIC GOLD MEDAL, TOP GUN, MULTI PURPOSEG rams**FEDERAL209A HI-SKOR * 411555300 FEDERAL209A HI-SKOR * 412055900 FEDERAL209A HI-SKOR * 412556600 FEDERAL209A HI-SKOR * 413257800 FEDERAL209A HI-SKOR * HI-SKOR * HI-SKOR * HI-SKOR * HI-SKOR * 411455000 FEDERAL209A HI-SKOR * 411955700 FEDERAL209A HI-SKOR * 412456200 FEDERAL209A HI-SKOR * 413257100 FEDERAL209A HI-SKOR * HI-SKOR * HI-SKOR * HI-SKOR * HI-SKOR * HI-SKOR * HI-SKOR * HI-SKOR * HI-SKOR *ACTIVTG-302411556100 FEDERAL209A HI-SKOR *ACTIVTG-302412006700 FEDERAL209A HI-SKOR *ACTIVTG-302412457300 FEDERAL209A HI-SKOR *ACTIVTG-302413358800 REMINGTON209P HI-SKOR * 411504700 REMINGTON209P HI-SKOR * 412055400 REMINGTON209P HI-SKOR * 412505900 REMINGTON209P HI-SKOR * 413256600 REMINGTON209P HI-SKOR * HI-SKOR * HI-SKOR * HI-SKOR * HI-SKOR * 411504200 REMINGTON209P HI-SKOR

10 * 411954800 REMINGTON209P HI-SKOR * 412505700 REMINGTON209P HI-SKOR * 413306500 REMINGTON209P HI-SKOR * HI-SKOR * HI-SKOR * HI-SKOR * HI-SKOR * HI-SKOR * HI-SKOR * HI-SKOR * HI-SKOR *ACTIVTG-302411454800 REMINGTON209P HI-SKOR *ACTIVTG-302412105500 REMINGTON209P HI-SKOR *ACTIVTG-302412506100 REMINGTON209P HI-SKOR *ACTIVTG-302413207000 WINCHESTER2 0 9 HI-SKOR * 411505100 WINCHESTER2 0 9 HI-SKOR * 412005700 WINCHESTER2 0 9 HI-SKOR * 412506400 WINCHESTER2 0 9 HI-SKOR * 413207500 WINCHESTER2 0 9 HI-SKOR * 0 9 HI-SKOR * 0 9 HI-SKOR * 0 9 HI-SKOR * 0 9 HI-SKOR * 411505200 WINCHESTER2 0 9 HI-SKOR * 411955800 WINCHESTER2 0 9 HI-SKOR * 412456400 WINCHESTER2 0 9 HI-SKOR * 413357800 WINCHESTER2 0 9 HI-SKOR * 0 9 HI-SKOR * 0 9 HI-SKOR * 0 9 HI-SKOR * 0 9 HI-SKOR * 0 9 HI-SKOR * 0 9 HI-SKOR * 0 9 HI-SKOR * 0 9 HI-SKOR *ACTIVTG-302411455600 WINCHESTER2 0 9 HI-SKOR *ACTIVTG-302411956300 WINCHESTER2 0 9 HI-SKOR *ACTIVTG-302412457000 WINCHESTER2 0 9 HI-SKOR *ACTIVTG-302413358400 SHOTSHELL TARGET DATA12 GAUGE 23 4 INCH 24 GRAM LOADSLEADMUZZLECHAMBERPRIMERIMR POWDERWAD (FT/SEC)(PSI)NOTE - ALL DATA SHOWN IS FOR LEAD SHOT.


Related search queries