INSTALLATION REMOTE ENGINE START SYSTEM IMPREZA ...

1 1 OF 14 ISSUE00 DATE9 Feb 2017 subaru OF AMERICAPART NUMBERH001 SFL101 PART NUMBER: H001 SFL101 DESCRIPTION: LONG RANGE TURN START REMOTE ENGINE START SYSTEM IMPREZA / CROSSTREK INSTALLATIONINSTRUCTIONS123 KIT CONTENTSTOOLS REQUIRED MEANING OF CHARACTERSCAUTION: DO NOT SECURE ANY REMOTE START HARNESSES TO ANY YELLOW HARNESSES / CONNECTORS (AIRBAG SYSTEM ) IN THE IV (DST-i) Diagnostic InterfacePhillips Screwdriver Short and StandardWire CuttersPanel Removal Tool: Remove : Tighten Torque: Install : Disconnect: Connect: Location of Clip or Screw: Loosen: Discard: Re-useBARatchet, 10mm Socket & ExtensionRemote ENGINE START Control Module (ECU)Quantity=1 REMOTE ENGINE StartWire HarnessQuantity=1 REMOTE ENGINE StartTransmitters w/ Warning TagsQuantity=2 Under Hood Warning LabelQuantity=1 Tie Wraps20cm Quantity=639cm Quantity=8 REMOTE START QUICK REFERENCE* REMOTE START Activation Press Two (2) Times Within Three (3) SecondsRemote START ActivationPress Two (2) Times Within (2) Seconds, Then Press and Hold For Three (3) SecondsLONG RANGE ACTIVATION - ALL MODELSALTERNATE ACTIVATION - PUSH BUTTON START MODELSR emote START ShutdownPress and Hold For Two (2) SecondsRemote START ShutdownPress and Hold For Three (3) SecondsNOTE: All vehicle doors, hood, trunk or rear gate must be closed prior to activating the REMOTE ENGINE START SYSTEM .

2 Any open entry point will prevent starting or cause the SYSTEM to shut successful activation, the REMOTE START fob will fl ash and beep one (1) time**, the horn will honk one (1) time and the side marker lights, tail lights and parking lights will fl ash one (1) time. The SYSTEM will check certain safety preconditions before starting and if all conditions are met, the ENGINE will START within fi ve (5) seconds. After the ENGINE starts, the REMOTE START fob will fl ash and beep two (2) times**, the horn will honk one (1) time and the side marker lights, tail lights and parking lights will fl ash one (1) time. While the ENGINE is running via the REMOTE ENGINE START SYSTEM , the REMOTE START fob will continue to fl ash one (1) time every three (3) seconds, the side marker lights, tail lights and parking lights will remain illuminated and the power window switches will be disabled. The ENGINE will continue to run for fi fteen (15) minutes unless one of the safety parameters below is triggered.

3 The SYSTEM also has a timer that will allow the SYSTEM to operate for a maximum of twenty (20) minutes (under multiple REMOTE START activations). Using the factory ignition key (Turn START models) or Access key (Push button START models) to turn on the ignition resets the twenty (20) minute the ENGINE turns over but does not START (or starts and stalls) the REMOTE ENGINE START SYSTEM will power off and then attempt to START the ENGINE three (3) additional times. The SYSTEM will not attempt to restart the ENGINE if it determines a vehicle malfunction is preventing it from starting. If the ENGINE does not START after the three (3) additional attempts, the REMOTE ENGINE START request will be START Safety ParametersFor safety and security reasons, the SYSTEM will fail to START or shut down the ENGINE during REMOTE START operation if any of the following occur: The REMOTE START SYSTEM has operated for twenty (20) minutes between ignition ON cyclesThe horn will honk three (3) times and the parking lights will fl ash three (3) times Any of the vehicle s doors, trunk or rear gate are open The horn will honk six (6) times and the parking lights will fl ash six (6) times The vehicle s hood is openThe horn will honk two (2) times and the parking lights will fl ash two (2) times The ignition key is resting in the ignition cylinder (Turn START models)The horn will honk two (2) times and the parking lights will fl ash two (2) times The transmission shifter is not in the park positionThe horn will honk two (2) times and the parking lights will fl ash two (2) times The vehicle s brake pedal is pressed before the vehicle ignition is turned ON The horn will honk two (2) times and the parking lights will fl ash two (2)

4 Times The vehicle s ENGINE idle speed has reached a level over 3,500 RPM (this will cause the vehicle to shut down) The vehicle s security SYSTEM is triggered by opening the door, trunk or rear gate (if the security SYSTEM is armed at the time of REMOTE START activation)In addition to the items above, if the vehicle s ENGINE management SYSTEM determines there is a safety risk due to a vehicle related problem, the ENGINE will shut : TO AVOID DANGER OF CARBON MONOXIDE, NEVER REMOTE START A VEHICLE IN A CLOSED SPACE SUCH AS A CLOSED : Laws in some communities require that the vehicle be within view of anyone using the REMOTE ENGINE START . In some areas, use of the REMOTE ENGINE START may violate state, provincial or local laws. Before using the REMOTE ENGINE START , check your state, provincial and local laws.* See the vehicle owner s manual for more details.** Provided that the REMOTE START fob is within the operating range of the SYSTEM .

5 P/N: 4280648, Rev -QuickReference CardQuantity=1 English, 1 FrenchHood Safety Switch, Mounting Bracket &10mm Mounting Bolt Quantity=1 Torque WrenchFoam TapeQuantity=1 TWARNING: / AVERTISSEMENTThis vehicle is equipped with a REMOTE controlled ENGINE starter. To reduce the risk of serious Injury or death, switch ENGINE startersystem into service mode and disconnect the vehicle batterybefore performing any service on the v hicule est dot d'un d marreur distance. Pour r duire les risques de blessures graves ou mortelles, mettre le d marreur distance en mode service et d brancher la batterie du v hicule avant d'effectuer des travaux d'entretien sur ToolAlcohol and TowelECU Foam TapeQuantity=12 OF 14 PART NUMBERH001 SFL101 ISSUE00 DATE9 Feb 2017 subaru OF AMERICA1. Using a 10mm socket/ratchet, disconnect the negative battery terminal. (FIGURE A) NOTE: Do not disconnect the battery cable from the battery post.

6 NOTE: DO NOT PROCEED TO THE NEXT STEP FOR ONE (1) MINUTE TO ALLOW TIME FOR THE AIRBAG POWER SUPPLY TO Using a panel removal tool, carefully remove the left side dashboard panel by starting at the bottom access notch and working upward to disengage four (4) pressure clips. (FIGURE B) Using a Phillips screwdriver, remove one (1) Phillips screw securing the lower dashboard panel on the left side of the dashboard. (FIGURE C)3. Using a panel removal tool, carefully remove the driver s left side lower dashboard panel by pulling straight out to disengage seven (7) pressure clips. Unplug all connectors attached to the dashboard panel. (FIGURE D) 4 VEHICLE PREPARATIONFIGURE AFIGURE BFIGURE DFIGURE C3 OF 14 ISSUE00 DATE9 Feb 2017 subaru OF AMERICAPART NUMBERH001 SFL1014 VEHICLE PREPARATION, continued4. Using a Phillips screwdriver, remove one (1) Phillips screw on the lower corner of the driver s right side lower dashboard panel.

7 Carefully remove the driver s right side lower dashboard panel by pulling straight out toward the rear of the vehicle to disengage six (6) pressure clips. (FIGURE E) NOTE: Do not pull from the bottom of the panel, doing so may result in damage to the panel or the retaining clips. FIGURE HFIGURE E6. Using a 10mm socket/ratchet/extension, remove the two (2) 10mm nuts securing the driver s side lower airbag/ knee bolster. (FIGURE G) Remove the lower airbag/knee bolster. Using a pick tool, disengage the yellow connector lock by lifting upward. (FIGURE H) Using a panel removal tool, carefully lift upward to unplug the electrical connector and place the airbag/ knee bolster panel in a safe area. FIGURE GFIGURE F5. Remove the steering column shroud. Using a Phillips screwdriver, remove one (1) Phillips screw on the left side face and one (1) Phillips screw on the right side face of the steering column shroud.

8 Carefully unsnap and remove the lower steering column shroud panel and then remove the upper steering column shroud panel. (FIGURE F) NOTE: Insert the ignition key into the ignition switch and turn to the ACC position to unlock and rotate the steering wheel to access the Phillips screws on the face of the steering column. Left SideRight Side4 OF 14 PART NUMBERH001 SFL101 ISSUE00 DATE9 Feb 2017 subaru OF AMERICA8. Using a panel removal tool, carefully remove the right side dashboard panel by starting at the bottom access notch and working upward to disengage four (4) pressure clips. (FIGURE J) FIGURE JFIGURE KFIGURE IFIGURE L9. Using a panel removal tool, carefully lift upward to disengage four (4) pressure clips and one (1) fi nger clip and then pull rearward to remove the passenger s side ornament panel. (FIGURE K) 7. Open the glove box and press inward on the sides of the glove box to disengage the retaining tabs from the glove box inner cover.

9 Disconnect the strut from the glove box. (FIGURE I) 10. Using a Phillips screwdriver, remove seven (7) Phillips screws securing the glove box inner cover. Disengage the six (6) pressure clips and disconnect the glove box lamp connector to remove the glove box inner cover. (FIGURE L) 4 VEHICLE PREPARATION, continued5 OF 14 ISSUE00 DATE9 Feb 2017 subaru OF AMERICAPART NUMBERH001 SFL10151. Locate the glove box inner cover and REMOTE ENGINE START ECU. Using alcohol, clean the back side of the glove box inner cover and ECU, as shown. (FIGURE M) Using the supplied double sided tape, remove the three (3) small release liners and attach the tape to the glove box inner cover. Ensure the tape is positioned against the vertical character line and fl at against the multi-level inner cover. Press fi rmly in place for at least 30 seconds. (FIGURE N) NOTE: Ensure the double sided tape is positioned away from any obstructions on the glove box inner Remove the one (1) large release liner from the double sided tape and attach the REMOTE ENGINE START ECU.

10 Ensure the corner of the ECU, closest to the small gray connector, is fl ush with the upper left corner of the tape, as shown. Press fi rmly in place for at least 30 seconds. (FIGURE O) NOTE: Ensure the ECU connectors will be facing toward the passenger s side of the vehicle when the inner cover is Using one (1) of the supplied 39cm tie wraps, secure the REMOTE ENGINE START ECU to the glove box inner cover. Trim off the excess tie wrap. (FIGURE P) REMOTE ENGINE START ECU MOUNTINGFIGURE MFIGURE OFIGURE PVertical Character LineMount Corner of ECU Flush with Corner of Foam TapeObstructionClean with AlcoholFIGURE N6 OF 14 PART NUMBERH001 SFL101 ISSUE00 DATE9 Feb 2017 subaru OF AMERICA68-PIN IGNITION SWITCH CONNECTIONS1. Adjust the tilt/telescopic steering column all the way out and Locate the plastic channel at the base of the steering column that protects the ignition wire harness.