1 Keysight 33210A . 10 MHz Function/Arbitrary Waveform Generator Data Sheet 10 MHz Sine and Square waveforms Pulse, Ramp, Triangle, Noise, and DC waveforms Optional 14-bit, 50 MSa/s, 8K point arbitrary Waveform Generator AM, FM, and PWM modulation types Linear & logarithmic sweeps and burst operation 10 mVpp to 10 Vpp amplitude range Graph mode for visual verification of signal settings Connect via USB, GPIB and LAN. Fully compliant to LXI Class C specification Measurement Characteristics Uncompromising per- Easy-to-use function- Waveforms Standard Sine, Square, Ramp, Tri- formance at an ality angle, Pulse, Noise, DC. Built-in arbitrary wave- Exponential rise, Ex- affordable price Front-panel operation of the 33210A . forms (available only ponential fall, Negative with Option 002 ARB) ramp, Sin(x)/x, Cardiac is straight-forward and user friendly. The Keysight Technologies, Inc. Waveform characteristics You can access all major functions 33210A Function/Arbitrary Waveform Sine with a single key or two.
2 The knob or generator is the latest addition to the Frequency range 1 mHz to 10 MHz numeric keypad can be used to adjust Amplitude (relative to 1 kHz). 332XX family. Waveforms are gener- frequency, amplitude, offset, and Flatness 1, 2 < 100 kHz dB. ated using direct digital synthesis 100 kHz to 5 MHz dB. other parameters. You can even enter (DDS) technology which creates 5 MHz to 10 MHz dB. voltage values directly in Vpp, Vrms, stable, accurate low distortion sine Harmonic distortion 2, 3. dBm, or as high and low levels. Timing < 1 Vpp 1 Vpp waves as well as square waves with parameters can be entered in Hertz DC to 20 kHz 70 dBc 70 dBc fast rise and fall times up to 10 MHz 20 kHz to 100 kHz 65 dBc 60 dBc (Hz) or seconds. and linear ramp waves up to 100 kHz. 100 kHz to 1 MHz 50 dBc 45 dBc For user defined waveforms, Option 1 MHz to 10 MHz 40 dBc 30 dBc Internal AM, FM, and PWM modu- Total harmonic distortion 2, 3. 002 provides 14-bit, 50 MSa/s 8K. lation make it easy to modulate DC to 20 kHz point arbitrary Waveform generation.
3 Waveforms without the need for a Spurious (non-harmonic) 2, 4. DC to 1 MHz 70 dBc Pulse generation separate modulation source. Linear 1 MHz to 10 MHz 70 dBc + 6 dB/octave and logarithmic sweeps are also built The 33210A can generate variable- Phase noise in, with sweep rates selectable from (10 kHz offset) 115 dBc / Hz, typical edge-time pulses up to 5 MHz. With 1 ms to 500 s. Burst mode operation Square variable period, pulse width, and am- Frequency range 1 mHz to 10 MHz allows for a user-selected number of plitude the 33210A is ideally suited to Rise/fall time 20 ns cycles per trigger. GPIB, LAN, and a wide variety of applications requir- Overshoot < 2%. USB interfaces are all standard, plus Variable duty cycle 20% to 80% (to 5 MHz). ing a flexible pulse signal. you get full programmability using 40% to 60% (to 10 MHz). Custom Waveform gen- SCPI commands. Asymmetry 1% of period + 5 ns (@ 50% duty). eration (Option 002) Jitter (RMS) 1 ns + 100 ppm of period External frequency ref- Ramp, triangle The optional 8K point arbitrary Frequency range 1 mHz to 100 kHz Waveform generator (Option 002) can erence (Option 001) Linearity < of peak output Variable symmetry to be used in the 33210A to generate Pulse The 33210A external frequency refer- complex custom waveforms.
4 With 14- Frequency range 1 mHz to 5 MHz ence lets you synchronize to an exter- Pulse width 40 ns minimum bit resolution, and a sampling rate of nal 10 MHz clock, to another 33210A , (period 10 s) 10 ns resolution 50 MSa/s, the 33210A gives you the Variable edge time 20 ns to 100 ns or to a Keysight 33220A or Keysight flexibility to create the waveforms you Overshoot < 2%. 33250A. Phase adjustments can be need. It also lets you store up to four Jitter (RMS) 300 ps +. made from the front panel or via a ppm of period waveforms in nonvolatile memory. computer interface, allowing precise Noise The Keysight IntuiLink arbitrary wave- phase calibration and adjustment. Bandwidth 7 MHz typical form software allows you to easily 8K-point arbitrary Waveform generator create, edit, and download complex (Option 002). waveforms using the Waveform editor. Frequency range 1 mHz to 3 MHz Or you can capture a Waveform us- Waveform length 2 to 8 k points ing IntuiLink for Oscilloscopes and Amplitude resolution 14 bits (including sign).
5 Sample rate 50 MSa/s send it to the 33210A for output. To Min. rise/fall time 70 ns typical find out more about IntuiLink, visit Linearity < of peak output 02. Measurement Characteristics (continued). Settling time < 500 ns to of final Deviation DC to 5 MHz 1. Add 1/10th of output amplitude and value PWM offset spec per C for operation outside Jitter (RMS) 6 ns + 30 ppm the range of 18 to 28 C. Carrier waveforms Pulse 2. Autorange enabled Non-volatile memory 4 waveforms Source Internal/External 3. DC offset set to 0 V. Internal modulation Sine, Square, Ramp, 4. Spurious output at low amplitude is 75. Common characteristics Triangle, Noise, Arb 7 dBm typical Frequency (2 mHz to 20 kHz) 5. Add 1 ppm/ C average for operation Accuracy 5 (10 ppm + 3 pHz) Deviation 0% to 100% of pulse width outside the range of 18 to 28 C. in 90 days 6. Sine and square waveforms above 3 MHz (20 ppm + 3 pHz) External modulation input are allowed only with an infinite burst in 1 year (for AM, FM, PWM) count Resolution 1 Hz (internal) Voltage range 5 V full scale 7.
6 Only available if Option 002 is installed 1 mHz (user). Input impedance 5 k typical Amplitude Bandwidth DC to 20 kHz Range 10 mVpp to 10 Vpp into 50 . 20 mVpp to 20 Vpp into Sweep open circuit Waveforms Sine, Square, Ramp Accuracy 1, 2 2% of setting Type Linear or Logarithmic (at 1 kHz) 1 mVpp Direction Up or Down Units Vpp, Vrms, dBm Sweep time 1 ms to 500 s Resolution 3 digits Trigger source Single, External or Internal DC offset Marker Falling edge of sync Range 5 V into 50 signal (programmable (peak AC + DC) 10 V into open circuit frequency). Accuracy 1, 2 2% of offset setting of amplitude Burst 6. 2 mV Waveforms Sine, Square, Ramp Resolution 3 digits Type Counted (1 to 50,000. Main output cycles), Infinite, Gated Impedance 50 typical Start/stop phase +360 to 360 . Isolation 42 Vpk maximum to earth Internal period 1 s to 500 s Protection Short-circuit protected, Gate source External trigger overload automatically Trigger source Single, External or Internal disables main output Trigger characteristics External frequency reference Trigger input (Option 001) Input level TTL compatible Rear panel input Slope Rising or Falling, Lock range 10 MHz 500 Hz selectable Level 100 mVpp to 5 Vpp Pulse width > 100 ns Impedance 1 k , typical Input impedance > 10 k , DC coupled Lock time < 2 seconds Latency < 500 ns Rear panel output Jitter (rms) 6 ns ( ns for pulse).
7 Frequency 10 MHz Trigger output Level 632 mVpp Level TTL compatible into (0 dBm), typical 1 k . Impedance 50 , typical Pulse width > 400 ns AC coupled Output impedance 50 typical Phase offset Maximum rate 1 MHz Range +360 to 360 Fanout 4 Keysight 33210As Resolution (or equivalent). Accuracy 20 ns Modulation AM. Carrier waveforms Sine, Square Source Internal/External Internal modulation Sine, Square, Ramp, Triangle, Noise, Arb 7. (2 mHz to 20 kHz). Depth to FM. Carrier waveforms Sine, Square Source Internal/External Internal modulation Sine, Square, Ramp, Triangle, Noise, Arb 7. (2 mHz to 20 kHz) 03. Measurement Characteristics (continued). Programming times (typical) General Ordering Information Configuration times USB LAN GPIB Power supply Cat II. Function change 120 ms 120 ms 120 ms 100 to 240 V @ Keysight 33210A . Frequency change 2 ms 3 ms 2 ms 50/60 Hz ( 5%, +10%) 10 MHz Function/Arbitrary Amplitude change 30 ms 30 ms 30 ms 100 to 120 V @ 400 Hz Select user arb 130 ms 130 ms 130 ms ( 10%).
8 Waveform generator Arb download times Binary transfer Power consumption 50 VA max (Option 002) Operating IEC 61010 Accessories included USB LAN GPIB environment Pollution Degree 2 Operating manual, service manual, 2 k points 5 ms 9 ms 10 ms Indoor Location quick reference guide, IntuiLink wave- 4 k points 8 ms 15 ms 20 ms Operating 0 to 55 C. 8 k points 14 ms 27 ms 40 ms temperature form editor software, test data, USB. Operating humidity 5% to 80% RH, cable, and power cord (see language non-condensing option). Operating altitude Up to 3000 meters Storage temperature 30 to 70 C Options State storage Power off state Opt. 001 External timebase reference memory automatically saved, Four user-configurable Opt. 002 8K-point arbitrary Waveform stored states generator Interface LAN LXI-C Ethernet 10/100. USB , GPIB Opt. A6J ANSI Z540 calibration Language SCPI 1993, Opt. AB0 Taiwan: Chinese manual Dimensions (W x H x D) Opt. AB1 Korea: Korean manual Bench top mm x mm Opt. AB2 China: Chinese manual x mm Opt.
9 ABA English: English manual Rack mount mm x mm Opt. ABD Germany: German manual x mm Opt. ABF France: French manual Weight kg ( lbs). Safety designed to UL-1244, CSA 1010 Opt. ABJ Japan: Japanese manual EN61010 Opt. PLG Continental European EMC tested to MIL-461C, EN55011, power cord EN50082-1. Vibration and shock MIL-T-28800, Type III, Other Accessories Class 5 34131A Carrying case Acoustic noise 30 dBa 34161A Accessory pouch Warm-up time 1 hour 34190A Rackmount kit 34191A Dual flange kit, 2U. 34194A Dual lock link kit 04. 05 | Keysight | 33210A 10 MHz Function/Arbitrary Waveform Generator - Data Sheet Evolving Since 1939 For more information on Keysight Our unique combination of hardware, software, services, and people can help you Technologies' products, applications or services, please contact your local Keysight reach your next breakthrough. We are unlocking the future of technology. office. The complete list is available at: From Hewlett-Packard to Agilent to Keysight . Americas Canada (877) 894 4414.
10 Brazil 55 11 3351 7010. Mexico 001 800 254 2440. United States (800) 829 4444. Asia Pacific Australia 1 800 629 485. China 800 810 0189. Hong Kong 800 938 693. India 1 800 11 2626. Japan 0120 (421) 345. myKeysight Korea 080 769 0800. Malaysia 1 800 888 848. A personalized view into the information most relevant to you. Singapore 1 800 375 8100. Taiwan 0800 047 866. Other AP Countries (65) 6375 8100. Register your products to get up-to-date product information and find warranty information. Europe & Middle East Austria 0800 001122. Keysight Services Belgium 0800 58580. Finland 0800 523252. Keysight Services can help from acquisition to renewal across your France 0805 980333. instrument's lifecycle. Our comprehensive service offerings one- Germany 0800 6270999. stop calibration, repair, asset management, technology refresh, Ireland 1800 832700. Israel 1 809 343051. consulting, training and more helps you improve product quality Italy 800 599100. and lower costs. Luxembourg +32 800 58580.