Mentor II User Guide - ELSA Solutions

1 GuideMentor IIDC Drives25A to 1850 AoutputPart Number: 0410-0013-14 Issue Number: 14 Safety InformationPersons supervising and performing the electrical installation or maintenance of a drive and/or an external Option Unit must be suitably qualified and competent in these duties. They should be given the opportunity to study and if necessary to discuss this user Guide before work is voltages present in the drive and external option units are capable of inflicting a severe electric shock and may be lethal. The Stop function of the drive does not remove dangerous voltages from the terminals of the drive and external Option Unit.

2 Mains supplies should be removed and left removed for a minimum of 2 minutes before any servicing work is performed. The installation instructions should be adhered to. Any questions or doubt should be referred to the supplier of the equipment. It is the responsibility of the owner or user to ensure that the installation of the drive and external Option Unit, and the way in which they are operated and maintained complies with the requirements of the Health and Safety at Work Act in the United Kingdom and applicable legislation and regulations and codes of practice in the UK or Stop and Start inputs of the drive should not be relied upon to ensure safety of personnel.

3 If a safety hazard could exist from unexpected starting of the drive, an interlock should be installed to prevent the motor being inadvertently informationThe manufacturer accepts no liability for any consequences resulting from inappropriate, negligent or incorrect installation or adjustment of the optional operating parameters of the equipment or from mismatching the drive with the contents of this user Guide are believed to be correct at the time of printing. In the interests of a commitment to a policy of continuous development and improvement, the manufacturer reserves the right to change the specification of the product or its performance, or the contents of the user Guide , without rights reserved.

4 No part of this user Guide may be reproduced or transmitted in any form or by any means, electrical or mechanical including photocopying, recording or by any information storage or retrieval system, without permission in writing from the publisher. Important! Drive software versionThis product is supplied with the latest version of user -interface and machine- control software. If this product is to be used with other control Techniques variable speed drives in an existing system, there may be some differences between their software and the software in this product.

5 These differences may cause a difference in functions. This may also apply to variable speed drives returned from a control Techniques Service there is any doubt, contact a control Techniques Drive January 2006 control Techniques Drives LtdIssue Number: 14 Mentor ll user Guide 3 Issue Number: 14 of Conformity.

6 41 Features of Mentor II .. II parameters .. phase-sequence .. feedback .. reference .. communications interface .. feedback .. resolution ..52 Safety Information .. , Cautions and Notes .. safety - general warning .. design and safety of personnel .. limits .. with regulations .. parameters ..63 Introduction .. motor control .. of the variable speed drive .. communications ..84 Data ..95 Mechanical Installation .. and ventilation ..146 Electrical Installation .. criteria .. connections .. feedback burden resistors.

7 Connections .. index .. classified ..267 Operating procedures .. and displays .. up to run .. started ..288 Parameter Set .. of parameters .. of parameters .. parameters that cannot be controlled by analogue input .. descriptions .. parameter descriptions .. 48 Menu 1: Speed reference .. 48 Menu 02: Ramps .. 50 Menu 03: Feedback selection and speed loop .. 51 Menu 04: Current selection and limits .. 54 Menu 05: Current loop .. 58 Menu 06: Field control .. 62 Menu 07: Analogue inputs & outputs .. 65 Menu 08: Digital inputs.

8 68 Menu 09: Status outputs .. 71 Menu 10: Status logic & diagnostic information .. 73 Menu 11: Miscellaneous .. 77 Menu 12: Programmable thresholds .. 79 Menu 13: Digital lock .. 80 Menu 14: MD29 system set-up .. 82 Menus 15 and 16: Applications menus .. 84MD24-PROFIBUS-DP set-up .. 86MD25-DeviceNet set-up .. 87MD-IBS (INTERBUS) set-up .. logic diagrams .. 899 Diagnostic procedures .. codes .. 10110 Serial communications .. Connecting to the drive .. Preliminary adjustments to the drive .. Routing the serial communications cable.

9 Termination .. Components of messages .. Structure of messages .. Multiple drives .. Wide integers - serial mode 4 .. Sending data .. Reading data .. Using Mentor on a network with other CT drives .. Global addressing .. 10411 Options .. MD29 .. CTNet (MD29AN) .. Interbus-S (MDIBS) .. Profibus-DP (MD24) .. DeviceNet (MD25) .. IO box .. Field control unit FXM5 .. 10512 Electromagnetic compatibility .. General note on EMC data .. Immunity .. Emission.

10 Recommended filters .. Radiated emissions .. Enclosure construction .. Motor cable selection .. 109 Index .. 1124 Mentor ll user Issue Number: 14 Declaration of ConformityControl TechniquesThe GroNewtownPowysUKSY16 3 BEThe DC variable speed drive product Mentor II current range 25A to 1850A, single quadrant and four quadrant versions, has been designed and manufactured in accordance with the following European harmonised, national and international standards.