Nylon Tubing Series T/TIA - SMC ETech

1 Temperature ( C) 200 20406080100 Max. operating pressure (MPa)T0425T0604T1613 Series TIAT0403 Other metric sizeNylon TubingSeries T/TIARoHSFor general pneumatic Tubing , Nylon tubingMax. Operating 40 to +100 C, Water: 0 to +70 C (No freezing) Nylon 12 Max. operatingpressure Note 1)(MPa)20 C or less40 C60 C80 C100 CMin. bending radius Bending value (Reference)One-touch fittings, Insert fittings, Self-align fittings, Miniature fittingsApplicable fittings Note 1) Note 2)Min. bendingradius (mm) Note 3)Operating temperature Note 1)Material1007515122520302350406548 ModelModelMetric size ( Series T)Inch size ( Series TIA) Tubing (mm) Tubing (mm)White (W)Red (R) Blue (BU) Yellow (Y) Green (G) Black (B) 20 m roll 100 m roll (T1613 is reel.)532"516"Nominal size (inch)1438"316"18"12"" (mm)Note 1) Be sure to operate under the maximum operating pressure conditions using the lower maximum op-erating specification of either the Tubing or 2) Mount an inner sleeve when using metal One-touch fittings in high-temperature environments of 60 C or more.

2 Use self-align fittings at a temperature of 60 C or 3) The minimum bending radius is the representative value measured as shown in the left 5SE A TUBE ABOVE THE RECOMMENDED MINIMUM BENDING RADIUS s 4HE Tubing MAY BE BENT IF USED UNDER THE RECOMMENDED MINIMUM BENDING RADIUS Therefore, refer to the refraction value and make sure that the Tubing is not bent or 0 LEASE NOTE THAT THE REFRACTION VALUE IS NOT WARRANTED BECAUSE OF THE VALUE WHEN 2 IS MEASURED by the method in the left figure if the Tubing is bent or flattened, to Order20T0425 BColorTubing modelSymbolColorBBlack (Translucent)WWhite (Material color)R2ED (Translucent)BUBlue (Translucent)YYellow (Translucent)GGreen (Translucent)PrecautionsHow to measure the minimum bending a temperature of 20 C, bend the tub-ing into a U shape. Fix one end and grad-ually move the other end closer. Measure 2 AT THE POINT WHERE THE OUTSIDE DIAME-ter's rate of change is 10%.

3 For general industrial water. Please consult with SMC if using other kinds of fluid. Surge pressure must be un-der the max. operating pressure. If the surge pressure exceeds the maximum op-erating pressure, it will result in damage to fittings and exercise caution when using this item in a clean room. There is a possibility of plasticizer and other materials precipi-tating on the tube surface and detracting from the cleanliness level of the endLength per rollSymbolLength2020 m roll100100 m roll2 Max. operating pressure MPaOperating temperature 40 20020406080100TS0604 Other than TS0425, TS0604 For general pneumatic Tubing Pliable soft Nylon Tubing 20 m roll 100 m roll (TS1612 is reel.) with water due to a change in materials. Compatible fluid types are printed on the tube body for differentiation, so please be sure to check this.

4 Note) If using the previous TS/TISA Series with water , the tube may shrink and cause air leakage or the tube may fall products which changed the material are applicable for general industrial water. Please contact SMC if using other kinds of pressure must be under the max. operating pressure. If the surge pressure exceeds the maximum operating pressure, it will result in damage to fittings and exercise caution when using this item in a clean room. There is a possibility of plasticizer and other materials precipitating on the tube surface and detracting from the cleanliness level of the to Order AvailabilityPart TS0604 TS0806 TS1075 TS1209 TISA01 TISA05 TISA07 TISA11 TISA13 ColorBlack, White,Red, Blue, Yellow, GreenRed, Blue, Yellow, Green100 m reel150 m reel200 m reel500 m reel 20 m rollLengthModelX3X4(Please contact SMC for specifications in detail, dimensions, delivery and specifications other than those mentioned above.

5 Made to OrderMetric size and Inch size except 16: Suffix -X3 to the end of part number. Ex.) TS0425R-100-X3 Metric size: Suffix -X3 to the end of part number. Ex.) TS0425G-500-X3 Inch size: Suffix -X4 to the end of part number. Ex.) TISA01BU-20-X4100 m reelLonger length reel20 m rollSoft Nylon TubingSeries TS/ TISAAt a temperature of 20 C, bend the tub-ing into a U shape. Fix one end and gradually move the other end closer. Measure 2R at the point where the out-side diameter's rate of change is 10%.ModelModelMetric size ( Series TS)Inch size ( Series TISA) Tubing sizeTS0425 TS0604 TS0806 TS1075 TS1209 TS1612 TISA01 TISA05 TISA07 TISA11 (mm) Tubing (mm)Black (B)White (W)Red (R)Blue (BU)Yellow (Y)Green (G)Printing/FluidPrint codeFluidSMC TS 0604 SOFTNYLON 6 x 4 SMC TS 0604 SOFTNYLON 6 x 4 PreviousNEWAirAir/Water532"516"Nominal size (inch)14"316"18"38"12"100TS0604 WLength per rollColorSymbolColorTubing modelBBlack (Translucent) WWhite (Material color)RRed (Translucent)BUBlue (Translucent)YYellow (Translucent)GGreen (Translucent)SymbolLength2020 m roll100100 m roll (Black and white only)How to OrderMax.

6 Operating (mm)SpecificationsFluidAir/Water Note 1) 40 to +100 C, Water: 0 to +50 C (No freezing) Nylon MPaNote 2)One-touch fittings, Insert fittings, Self-align fittings, Miniature fittings Note 2) 3)Operating temperature Note 2)MaterialMin. bending radiusBending value (Reference)20 C or less40 C60 C80 C100 CNote 1) Refer to the Printing/Fluid .Note 2) Be sure to operate under the maximum operating pressure and operating temperature conditions using the lower specifications of either the Tubing or 3) Mount an inner sleeve when using metal One-touch fittings in high-temperature environments of 60 C or more. Use self-align fittings at a temperature of 60 C or 4) The minimum bending radius is the representative value measured as shown in the left 5SE A TUBE ABOVE THE MINIMUM BENDING RADIUS s 4HE Tubing MAY BE BENT IF USED UNDER THE MINIMUM BENDING RADIUS 4 HEREFORE REFER TO THE BENDING VALUE AND MAKE sure that the Tubing is not bent or 0 LEASE NOTE THAT THE BENDING VALUE IS NOT WARRANTED BECAUSE OF THE REPRESENTATIVE VALUE WHEN 2 IS MEASURED BY the method in the left figure if the Tubing is bent or flattened, bending radius mm Note 4)2 RFixed endHow to measure the minimum bending at 20 CRefer to burst pressure characteristics curve.

7 20 to +60 C (No freezing)PolyurethaneMax. operating pressureBurst pressureMin. bending radius (mm)Operating (mm)Tube (mm)Black (B)White (W)Red (R)Blue (BU)Yellow (Y)Green (G)Opaque (N)(1)(2)One-touch fitting, Insert tube fitting, Hose nipple(3) Yellow brown (YB)815152229 Tube drawingstrenght NWithoutinner sleeveWithinner sleeve(Using One-touch fitting)1560608511080230250300480 Note1) Not clear but opaque due to ) Min. bending radius is measured as shown in the figure tube fitting: 100m roll: 20m rollPart tube modelTUS0425 TUS0604 TUS0805 TUS1065 TUS1208 MaterialWall thicknessC2700T (Nickel plated) per rollSymbolColourIndication oftube modelBBlackWWhiteRRedBUBlueYYellowGGreen NOpaqueYBYellow brownSymbolRoll sizeColour indication2020m roll100100m roll (Black, Blue only) CautionqUse Nylon or polyurethane Tubing for general industry water to prevent the Tubing from coming out or bursting due to possibility of surge pressure generation.

8 WThe value of the max. operating pressure is at a temperature of 20 C. Refer to the burst pressure characteristics curve for other tem-peratures. Avoid abnormal temperature rise which may burst the Tubing . eThe value of the min. bending radius is at a temperature of 20 C. Higher temperatures allows the Tubing to bend inner sleeve taking the removing force into consideration when used with One-touch ) Always use inner sleeve ( Series TJ) in safety circuit or critical Polyurethane TubingSeries TUSTUS related accessorieslnner SleeveSeries TJModelSpecificationsReinforces soft polyurethane an inner sleeve into softpolyurethane Tubing when used with aOne-touch the tube into U-form at atemperature of 20 one end and close loopgradually. Measure 2R whenthe tube breaks or is to OrderSuitable for piping in confined spacesExtremely flexibleSoft Polyurethane TubingSeries TableSpecificationsBurst Pressure Characteristics CurvePrecautionsRoHS44 Tubing inside diameter comparison(mm)Maximum effective area increased nearly 44%TUH/Standard Type(Compared to polyurethane Tubing TU0805.

9 8mm, length 1m)Operating pressure (at 20 C)TUH/High Pressure TypeHas the same operating pressure as Series TS soft Nylon Tubing , and a bending radius equivalent toseries TU polyurethane ( D1)TUH/Standard typeTUH/High pressure 5 Hard Polyurethane TubingSeries TUH ( D1) ( D2) ( D2)Can be restored even after foldingRestoration is outstanding compared to Nylon Tubing , leaving no creases from Polyurethane TUH (Standard Type) PolyurethaneTUSoft mmBlack (B)White (W)Blue (BU)Translucent (N) 20m bundle 100m Polyurethane Tubing /Standard TypeSeries TUHS pecificationsFluidMax. operatingpressure(at 20 C)Burst pressureOperatingtemperatureMaterialAir Note 1) Note 2)Refer to the burst pressure characteristics bending radius mm10 20 to 60 CPolyurethane TUH0644 B20 ColorBlack WhiteBlueTranslucentSymbolBWBUNC olorTubing modelLength 20m bundle100m bundleSymbol 20100 Bundle lengthHow to OrderBurst Pressure Characteristic Curveand Operating Pressure543210-20020 Operating temperature CBurst pressure MPa406018243036At a temperature of 20 C bend the Tubing into a U shape.

10 Then with one side fixed, gradually close the other side and measure 2R at the point where the Tubing folds or flattens, sideNote 1) Consult SMC regarding other cannot be used due to the occurrence of 2) The maximum operating pressure is the value at 20 C. Refer to the burst pressure characteristic curve for other , an abnormal temperature increase due to adiabatic compression can cause Tubing to 3) The minimum bending radius is measured at 20 C using the method shown in the figure at the left. At higher temperatures, breakage or flattening, etc., may occur at more than the minimum bending operating mmBlack (B)White (W)Blue (BU)Translucent (N) 20m bundle 100m bundleTUH1208128 SpecificationsFluidMax. operatingpressure(at 20 C)Burst pressureOperatingtemperatureMaterialAir Note 1) Note 2)Refer to the burst pressure characteristics bendingradius mm10 20 to 60 CPolyurethaneTUH0604 B20 ColorBlackWhiteBlueTranslucentSymbolBWBU NC olorTubing ModelLength 20m bundle100m bundleSymbol 20100 Bundle lengthHow to Order56743210-20020 Operating temperature CBurst pressure MPa406015202735 Maximum operating pressure2 RFixed sideNote 1) Consult SMC regarding other cannot be used due to the occurrence of 2) The maximum operating pressure is the value at 20 C.