SIMATIC TIA Portal STEP 7 Basic V10 - Siemens

1 SIMATIC TIA Portal step 7 Basic _____TIA Portal Introduction 1 Simple example 2 Extended example 3 Example "PID control" 4 Example "Motion" 5 SIMATIC TIA Portal step 7 Basic Getting Started 12/2009 A5E02651459-01 Legal information Legal information Warning notice system This manual contains notices you have to observe in order to ensure your personal safety, as well as to prevent damage to property. The notices referring to your personal safety are highlighted in the manual by a safety alert symbol, notices referring only to property damage have no safety alert symbol.

2 These notices shown below are graded according to the degree of danger. DANGER indicates that death or severe personal injury will result if proper precautions are not taken. WARNING indicates that death or severe personal injury may result if proper precautions are not taken. CAUTION with a safety alert symbol, indicates that minor personal injury can result if proper precautions are not taken. CAUTION without a safety alert symbol, indicates that property damage can result if proper precautions are not taken. NOTICE indicates that an unintended result or situation can occur if the corresponding information is not taken into account.

3 If more than one degree of danger is present, the warning notice representing the highest degree of danger will be used. A notice warning of injury to persons with a safety alert symbol may also include a warning relating to property damage. Qualified Personnel The product/system described in this documentation may be operated only by personnel qualified for the specific task in accordance with the relevant documentation for the specific task, in particular its warning notices and safety instructions. Qualified personnel are those who, based on their training and experience, are capable of identifying risks and avoiding potential hazards when working with these products/systems.

4 Proper use of Siemens products Note the following: WARNING Siemens products may only be used for the applications described in the catalog and in the relevant technical documentation. If products and components from other manufacturers are used, these must be recommended or approved by Siemens . Proper transport, storage, installation, assembly, commissioning, operation and maintenance are required to ensure that the products operate safely and without any problems. The permissible ambient conditions must be adhered to. The information in the relevant documentation must be observed.

5 Trademarks All names identified by are registered trademarks of the Siemens AG. The remaining trademarks in this publication may be trademarks whose use by third parties for their own purposes could violate the rights of the owner. Disclaimer of Liability We have reviewed the contents of this publication to ensure consistency with the hardware and software described. Since variance cannot be precluded entirely, we cannot guarantee full consistency. However, the information in this publication is reviewed regularly and any necessary corrections are included in subsequent editions.

6 Siemens AG Industry Sector Postfach 48 48 90026 N RNBERG GERMANY A5E02651459-01 12/2009 Copyright Siemens AG 2009. Technical data subject to change step 7 Basic Getting Started, 12/2009, A5E02651459-01 3 Table of contents 1 TIA Portal Overview ..5 TIA Portal TIA Portal Engineering Data management ..9 Views in the TIA Navigation in the TIA Portal Project Example Overview ..15 Loading a 2 Simple Create Inserting and configuring a Inse rting a Overview of device and network Configure Create What are organization blocks?

7 31 Open organization block ..32 Overview of the program What are networks?..35 Inserting LAD What are tags?..42 Defining and interconnecting PLC Test Loading the program to the target Test program with program Create HMI Visualization in the TIA Create HMI device with HMI screen ..57 What are graphic objects? ..65 Creating and configuring graphic "Machine ON/OFF" Graphic objects "LEDs"..69 Graphic object "Conveyor"..74 Graphic object "Bottle" with motion simulation ..77 Modify visibility of motion animation.

8 82 Testing HMI Load HMI screen to the HMI device ..85 Simulate Table of contents step 7 Basic 4 Getting Started, 12/2009, A5E02651459-01 3 Extended Introduction ..89 Expanding the Decl aring tags in the PLC tag table ..91 Programming the conditions for starting the Querying the status of the machine ..95 Querying the position of the bottle and the status of the heating chamber ..97 Query pasteurization Control Programming the conditions for stopping the Programming the PLC of the 107 Programming the heating 110 Programming the st atus light.

9 113 Test expanded program with program status ..117 Expand HMI Graphic object "Heating chamber"..123 Graphic object "Heating chamber LED"..125 Graphic objects "Light barriers"..127 Simulate HMI 4 Ex ample "P ID control"..135 Set organization block for PID Create technological object PID Load simulation Configure PID co Changing the heating chamber Integrate temperature comparison as condition in control program ..154 Adjust HMI Activ e PID controller in online 5 Ex ample "Motion" ..165 Insert technological object "Axis".

10 168 Configure technological object "Axis".. 170 Enable Posi tion axis relative ..176 Expand HMI Change graphic object Create second graphic object bottle ..182 Connect HMI objects with motion Simulate HMI Start diagnostics view ..191 Glos sary ..197 step 7 Basic Getting Started, 12/2009, A5E02651459-01 5 TIA Portal Introduction Overview Introduction Welcome to the "STEP7 Basic Getting Started". Getting Started uses an example project to show you the easy operation of the TIA Portal . Example project The example project that is created in this Getting Started is a station for pasteurizing milk in a heating chamber.