1 SIMODRIVE 611 digital digital Drive Technology Drive Converters Configuration Manual Edition 10/2014. Answers for industry. Preface, Table of Contents Overview of the 1. Drive System 2. System Configuration Motor Selection and 3. SIMODRIVE 611 digital Position/Speed Sensing 4. Control Units Drive Converters 5. Power Modules 6. Infeed Modules Configuration Manual 7. Line Supply Connection 8. Important Circuit Information 9. Cabinet Design and EMC. 10. Connection Diagrams 11. Service and Spare Parts 12. Dimension Drawings A. Abbreviations and Terminology Valid for B. Equipment series 6SN11 References Certificates/ C. Declarations of Conformity D.
2 Index 10/2014 Edition SIMODRIVE documentation 3ls Printing history Brief details of this edition and previous editions are listed below. The current configuring manual replaces the previous version. The status of each edition is shown by the code in the Remarks column. Status code in the Remarks column: New documentation Unrevised reprint with new Order No. Revised edition with new status Edition Order No. Remarks 6SN1060 0AA01 0BA0 A. 6SN1197 0AA00 0BP0 C. 6SN1197 0AA00 0BP1 C. 6SN1197 0AA00 0BP2 C. 6SN1197 0AA00 0BP3 C. 6SN1197 0AA00 0BP4 C. 6SN1197 0AA00 0BP5 C. 6SN1197 0AA00 0BP6 C. 6SN1197 0AA00 0BP7 C. 6SN1197 0AA00 0BP8 C.
3 6SN1197 0AA00 1BP0 C. 6SN1197 0AA00 1BP1 C. 6SN1197 0AA00 1BP2 C. 6SN1197 0AA00 1BP3 C. 6SN1197 0AA00 1BP4 C. Trademarks All names identified by R are registered trademarks of Siemens AG. The remaining trademarks in this publication may be trademarks whose use by third parties for their own purposes could violate the rights of the owner. We have reviewed the contents of this publication to ensure consistency with the hardware and software described. Since variance cannot be precluded entirely, we cannot guarantee full consistency. However, the information in this publication is reviewed regularly and any necessary corrections are included in subsequent editions.
4 Copyright ESiemens AG 1993 2014. All rights reserved. Subject to change without prior notice. Printed in the Federal Republic of Germany Siemens Aktiengesellschaft Foreword Reader's note The Configuration Manual describes a reference state, which when observed, ensures the required reliable operation and compliance with the standards that have been taken into account. For deviations from the requirements laid down in the Configuration Manual, suitable measures must be applied, for example, measure- ments, securing or verifying that the required reliable operation is guar- anteed and that the standards to be taken into account are complied with from a regulatory perspective.
5 The documentation must be completely read, understood and taken into account before the devices are commissioned. If parts of the documentation have not been adequately understood, then please contact your local Siemens person before you continue to work with the devices. The contents of this document are neither part of an earlier or existing agreement, commitment or contractual relationship, nor do they change this. Siemens is obliged to fulfill all requirements specified in the applicable sales contract, which also contains all the valid terms of warranty. Any statements contained herein neither create new warranties nor modify the existing warranty.
6 Structure of the The SIMODRIVE documentation is subdivided into the following levels: documentation S General Documentation/Catalogs S User Documentation S Manufacturer/Service Documentation Additional infor- You can find information on the following topics under the following link: mation S Ordering documentation/overview of documents S Links to download documents S Using documentation online (searching and scanning through manuals/in- formation). If you have any questions regarding the technical documentation ( , sugges- tions, corrections), then please send an e mail to the following address Softwaredownload You can find the software under the following internet adress: SimoCom U > Produkt Support > Drive Technology > Converters > Low-voltage Converters > SIMODRIVE Converter system > SIMODRIVE POSMO.
7 Entry type: Download Search item: SimoCom U. Siemens AG 2014 All Rights Reserved SIMODRIVE 611 Configuration Manual (PJU) 10/2014 Edition v Forword My Documentation Information is provided under the following link as to how you can individually Manager compile documentation based on Siemens content, and adapt this for your own machine documentation: Training Information about SITRAIN Siemens training courses for products, systems and solutions in automation technology is provided under the following link: FAQs You can find Frequently Asked Questions in the Service&Support pages under Product Support: Target group This documentation addresses machine manufacturing companies (OEMs) that wish to configure, construct and commission a drive line up based on SIMODRIVE components.
8 Technical Support Local country telephone numbers for technical support are provided in the Inter- net under Contact: Certificates You will find the certificates for the products described in this documentation in the Internet: under the Product/Order No. 15257461. or contact the relevant branch office of the A&D MC group of Siemens AG. All declarations of conformity and certificates such as CE, UL, etc., are per- formed with the system components described in the associated Configuration Manuals or catalogs and, thus, are only valid if the described components are used in the device or facility. Note The use of components not released by Siemens may require the user to prepare new certificates/declarations of conformity.
9 Siemens AG 2014 All Rights Reserved vi SIMODRIVE 611 Configuration Manual (PJU) 10/2014 Edition Forword Repairs Note Repairs may be performed only by workshops authorized by Siemens who must use genuine spare parts. Unauthorized repairs and the use of other spare parts can result in personal injuries and property damage as well as loss of UL. approvals and safety functions, such as Safety Integrated. Warning ! SIMODRIVE converters are used in high voltage installations and are operated at voltages that when touched can cause serious injuries or death! Proper use Note the following: Warning ! Siemens products may only be used for the intended use in applications described in the catalog and the associated technical documentation.
10 If third party products and components are used, then these must either be recommended or certified by Siemens. The perfect and safe operation of products assumes that they have been correctly transported, correctly stored, located, mounted, installed, commissioned, operated and maintained. The permissible environmental conditions must be complied with. Information and instructions in the associated documentation must be observed. Definition: Setup and operation of the device/equipment/system in question must only be Who are qualified performed using this documentation. Commissioning and operation of a device/. personnel? system may only be performed by qualified personnel.