Example: marketing
Stress and Failure Analysis of Thick Walled Cylinder with ...
The Finite Element Analysis is conducted using commercial solver ANSYS Workbench in determining the Max Principal Stress, Equivalent (von-Mises) Stress, Radial & Hoop Stress distributions all the cases. The variation of the stress concentration factor and the maximum failure pressure in each case is calculated and tabulated.
Tags:
Information
Domain:
Source:
Link to this page:
Documents from same domain
Performance Analysis of a Heat Recovery Steam …
www.ijert.orgThe Heat Recovery steam Generator is one of the Critical components is the combined cycle (Gas Turbine cycle and Steam Power cycle) and is the most efficient energy conversation system in recent trends. Its function is to recover the waste heat present in the exhaust Gases of the Gas turbine ...
Analysis, Design and Simulation of Bidirectional DC- DC ...
www.ijert.orgThe bidirectional dc-dc flyback converters, a very simple structure, but the active switch suffer a high voltage stresses due to the leakage inductance of the transformer.
Optimization of Sand Casting Process Parameter …
www.ijert.orgCasting defects have been selected as the most representative quality characteristics in the ... Maximizing η’ leads to minimization of quality loss due to defects.
Design of High Gain Two stage Op-Amp using …
www.ijert.orgThe Operational Amplifier (Op-Amp) is designed and analyzed by using Cadence ICFB full custom design suite using 90nm technology. The ...
Numerical Study of Knife Edge Effects in Flash Riveted ...
www.ijert.orgabout knife edge is due to stress cycles causing fatigue cracks. In the riveting process of machine countersunk, cracks mainly initiated around the rivet holes in the upper skin. In flush fasteners, the influence of rivet head in conjunction with the skin thickness on the stress distribution is still largely ...
4-Bit Arithmetic And Logic Unit Design Using Structural ...
www.ijert.orgVery high scale integrated circuit Hardware Description Language. 1. Introduction The ALU, or the arithmetic and logic unit, is the section of the processor that is involved with executing operations of an arithmetic or logical nature. ... Design with VHDL” McGraw Hill, 2 nd
Programmable DC Electronic Load for Testing on-Board ...
www.ijert.orgThe Block diagram of programmable DC electronic load is as show in the Fig.1.The input voltage to device is between 6V-10V.Synchronous buck converter regulates the input voltage to constant voltage of 5V.The bias voltage for timer and Op-Amp are derived from the output of buck regulator .IC555 timer generates the required control signal, the ...
Design and Performance Study of Shell and Tube Heat ...
www.ijert.orgShell & tube type heat exchangers are built of tubes (round or rectangular in general) mounted in shells (cylindrical, rectangular or arbitrary shape). The differences lie mainly in the detailed features of construction and provisions for differential thermal expansion between the tubes and the shell. ...
A Resonant Converter Topology for Bidirectional DC DC ...
www.ijert.orgthe existing bidirectional dc-dc converters fall into the generic circuit structure illustrated in figure 11.Based on the placement of the auxiliary energy storage, the bidirectional dc-dc converter can be categorized into buck and boost type. To realize the double sided
Speed Control of Induction Motor using PWM Technique
www.ijert.orgfor single phase AC induction motor. It has low cost, high efficiency drive capable of supplying a single phase induction motor with PWM modulated sinusoidal voltage. The circuit operation control by an 8051 family microcontroller[4].The device is aimed at substituting commonly used TRIAC phase angle control drives. ...
Related documents
Design of pressure vessel using ASME codes and a ...
www.irjet.netGeometrical specification of the pressure vessel Thickness calculation from ASME codes Finite element verification of the code Design optimization using finite element analysis Results representation 3.3 Design Requirements Inner diameter of the pressure vessel d=3500mm Design Pressure: 3.5Mpa
Asset Integrity Management - Home | SGS
www.sgs.comn Finite Element Analysis n Mechanical Integrity Management n Pipeline Integrity Management n Remaining Life Calculations n Data Gathering and Field Inspections ... in new equipment design, pressure vessel component analysis and pipe stress analysis. The engineers performing the analysis have extensive knowledge and
Two Dimensional Analysis – Plane Stress and Plane Strain
academic.csuohio.eduTwo Dimensional Analysis – Plane Stress and Plane Strain ... walled pressure vessel (hot dog stresses). In fact any cylindrical pressure vessel, thin walled ... (this is not a depiction of a finite element). Line AB becomes longer as it moves from its original position, marked in …
Product Catalogue - Henry Group
www.henry-group.net• Finite Element Analysis • Pressure vessel design software • 3D scanning • 3D Printing Our engineers are also on hand to support technical questions from the industry and have representation or membership in all of the major industry organisations such as: • AIRAH (Aus)
Tank and Cylinder Fittings - Phoenix Forge
www.phoenixforge.comThe finite element analysis summarized in the above figures were performed to confirm the strength-equivalence between a standard Phoenix Forge Group ASME B16.11, Class 3000 threaded coupling and threaded fittings, when welded to a pressure vessel in accordance
PRESSURE VESSELS, Part I: Pressure Vessel Design, Shell ...
etcfunsafe.comA pressure vessel is considered as any closed vessel that is capable of ... stress may depend upon use of stringent material, analysis, examination, and testing requirements. Therefore, different codes can arrive at different resulting wall thickness yet ... checks according to Finite Element Analysis (FEA) are more and more extended
Pressure Vessel Engineering Ltd.
www.pveng.com2 - Designing for External Pressure Page4 of 40 Summary: Comments: See web write up section 2 - Designing for External Pressure. This simple vessel is designed to code rules for external pressure, here the results are verified using Finite Element Analysis (FEA). The FEA results show that the code calculations are bit more conservative than the
ANALYSIS AND DESIGN OF VERTICAL VESSEL FOUNDATION
ethesis.nitrkl.ac.inChapter 3 deals with the analysis of the vessel superstructure. Chapter 4 discusses the manual calculation of design of anchor bolts, pedestal and the footing using the available literatures. Chapter 5 shows the design results of the octagonal footing by manual calculation and with the help of finite element software.
Design and Study of Floating Roofs for Oil Storage Tanks
www.ijedr.orgusing three different analysis methods to study the deflection and stresses. The results show that the nonlinear finite element analysis is the most accurate and applicable one to be used in the design of the floating roof deck, since it simulates the exact loading cases that happen in reality.
Pressure Vessel Engineering Ltd. provides: ASME Vessel ...
www.pveng.compressure is the pressure in the pipe. HT is the average pressure along the length. mhT is measured at the point 1/3 up the triangle, the centroid of the force. The ASME rules reduce the width of the gasket. This load is a design rule, not a predictor of actual flange stresses. For FEA analysis, the load HT is applied at the moment arm mhT away