Table of Contents - Innova
obd ii certified engine family efn2.6ybt2ba displacement 2.6l this vehicle conforms to u.s. epa and state of california regulations applicable to 1999 model year new tlev passenger cars. refer to service manual for additional information tune-up conditions: normal …
Tags:
Manual, Content, Table of contents, Table
Information
Domain:
Source:
Link to this page:
Please notify us if you found a problem with this document:
Documents from same domain
Table of Contents
csr.innova.comintroduction 1 safety precautions / warnings 2 controls and indicators 4 preparation and caution before use 5 testing procedures 6 a. ac/dc voltage measurement 6 b. resistance measurement w (ohms) 6 c. diode test 7 d. continuity test 8 e. ac/dc current measurement (amps) 8 f. battery test 10 battery and fuse replacement 11
3300 Multimeter English SinglePage New
csr.innova.comtest lead at the location from which the wire was disconnected (series con-nection). 6. Reconnect the battery, or apply power to the circuit being tested. 7. Read the results on the display. CAUTION: After the test is completed, shut the power off to the circuit before removing the test leads and before reconnecting any disconnected wires or ...
Table of Contents - Innova
csr.innova.comfrom carbon monoxide poisoning, operate the vehicle ONLY in a well-ventilated area. To protect your eyes from propelled objects as well as hot or caustic liquids, wear approvedalways safety eye protection. When an engine is running, many parts (such as the coolant fan, pulleys, fan belt etc.) turn at high speed. To avoid serious
Timing Light (basic) - Innova
csr.innova.comXenon Bulb — Used to illuminate timing marks for checking timing. 2. Swiveling Head — Contains the xenon bulb. Rotates over approximately 90° to allow for easy illumination of timing marks in hard to reach locations. 3. Control Panel — Contains the controls and indicators necessary to operate the timing light. 4.
Table of Contents
csr.innova.comJan 08, 2020 · measurement (USA or Metric) as follows: 1. Select the desired display language, then press ENTER. The Select Unit screen displays. 2. Select the desired unit of measurement, then press ENTER. After the initial language and unit of measurement selections are performed, these, as well as other settings, can be changed as desired.
Table of Contents
csr.innova.comJan 07, 2020 · ABS icon - Indicates the currently displayed DTC is an Anti-Lock Braking System code. 7. ... Each fault is assigned a code number that is specific to that fault. ... any Diagnostic Trouble Codes that are in the vehicle's computer memory. ng the Code Reader Usi
System, Code, Anti, Fault, Locks, Anti lock braking system, Braking
Table of Contents - Innova
csr.innova.comNov 01, 2019 · Table of Contents i SAFETY PRECAUTIONS ... Reinstall the battery cover on the back of the Scan Tool. Adjustments After Battery Installation The first time the Scan Tool is turned on, you must select the desired display language (English, French or Spanish) and unit of …
Table of Contents - Innova
csr.innova.comKit” is available that makes it possible to upload retrieved data to a personal computer. 4. DTC Display Area - Displays the Diagnostic Trouble Code (DTC) number. Each fault is assigned a code number that is specific to that fault. 1 3 2 4 10 11 9 12 8 6 5 7
Related documents
OBDII/EOBD Code Reader (00-) 3388
www.free-instruction-manuals.commanual thoroughly before operating your code reader. The safety messages ... The Data Link Connector (DLC) is a standard 16-pin interface located under the dashboard on the driver’s side of the passenger compartment. If the DLC is not ... A. OBD II Cable - provides communication for vehicle DLC.
Table of Contents - on-board diagnostic s
www.onboarddiagnostics.com4. OBD II CONNECTOR-Connects the Code Scanner to the vehicle’s Data Link Connector (DLC). 3.2 Product Specifications y Display-Backlit LCD, 2 lines, 8 characters each 7 y Operating Temperature - 0 to 50℃ (﹣32 to 122℉) y Storage Temperature - ﹣20 to 70℃ (﹣4 to 158℉) y Power- DC12V provided via the vehicle’s battery y Dimensions:
Operating, Board, Connectors, Link, Diagnostics, On board diagnostic, Link connector
EVAP SYSTEM MONITOR DRIVE CYCLE INSTRUCTIONS
ww2.justanswer.comSep 10, 2010 · 1. Connect the Scan Tool to the data link connector (DLC). Use the Scan Tool to clear any stored DTC's and to reset the Onboard Diagnostic Monitors. Bring up the Readiness Code for the EVAP System Monitor. 2. Start the engine (cold); IAT PID from 40-100ºF (this step requires a key "off" period of at least 8 hours). 3.
System, Drive, Instructions, Cycle, Connectors, Link, Monitor, Diagnostics, Onboard, Link connector, System monitor drive cycle instructions, Onboard diagnostic
Vanguard 37 EFI Repair Manual - Mud Buddy
www.mudbuddy.comand is a 6-pin connector, which is electrically connected to the ECM. The DTC’s stored in the ECM’s memory can be retrieved through a hand-held diagnostic code reader plugged into the DLC, or a PC based software program de-signed to interface with the ECM data stream. On-Board Diagnostic (OBD…