TXS0104E 4-Bit Bidirectional Voltage-Level Translator for ...

1 TXS0104E 4-Bit Bidirectional Voltage-Level Translator for Open-Drain and Push-PullApplications1 Features No Direction-Control Signal Needed Max Data Rates 24 Mbps (Push Pull) 2 Mbps (Open Drain) Available in the Texas Instruments NanoFree Package V to V on A port and V to V on Bport (VCCA VCCB) No Power-Supply Sequencing Required VCCA orVCCB Can Be Ramped First latch -Up Performance Exceeds 100 mA Per JESD78, Class II ESD Protection Exceeds JESD 22 A Port 2000-V Human-Body Model (A114-B) 200-V Machine Model (A115-A) 1000-V Charged-Device Model (C101) B Port 15-kV Human-Body Model (A114-B) 200-V Machine Model (A115-A) 1000-V Charged-Device Model (C101) IEC 61000-4-2 ESD (B Port) 8-kV Contact Discharge 10-kV Air-Gap Discharge2 Applications Handset Smartphone Tablet Desktop PC3 DescriptionThis 4-Bit non-inverting Translator uses two separateconfigurable power-supply rails.

2 The A port isdesigned to track VCCA. VCCA accepts any supplyvoltage from V to V. VCCA must be less thanor equal to VCCB. The B port is designed to trackVCCB. VCCB accepts any supply voltage from V V. This allows for low-voltage bidirectionaltranslation between any of the , , , and5-V voltage the output-enable (OE) input is low, all outputsare placed in the high-impedance TXS0104E is designed so that the OE inputcircuit is supplied by ensure the high-impedance state during power upor power down, OE should be tied to GND through apulldown resistor; the minimum value of the resistor isdetermined by the current-sourcing capability of Information (1)PART NUMBERPACKAGEBODY SIZE (NOM)TXS0104 EDSOIC (14) mm mmTXS0104 EPWTSSOP (14) mm mmTXS0104 EZXUBGA (12) mm mmTXS0104 ERGYVQFN (14) mm mmTXS0104 EYZTDSBGA (12) mm mmTXS0104 ENMNnFBGA (12) mm mm(1) For all available packages, see the orderable addendum atthe end of the data Voltage (V) Input Voltage (V) VGATE = VVGATE = VVGATE = VVGATE = VVGATE = VC001 VGATE = V VGATE = V VGATE = V VGATE = V VGATE = V Transfer Characteristics of an JUNE 2006 REVISED OCTOBER 2020 Copyright 2020 Texas Instruments IncorporatedSubmit Document Feedback1 Product Folder Links.

3 TXS0104 ETXS0104 ESCES651I JUNE 2006 REVISED OCTOBER 2020An IMPORTANT NOTICE at the end of this data sheet addresses availability, warranty, changes, use in safety-critical applications,intellectual property matters and other important disclaimers. PRODUCTION of Contents1 Revision Pin Configuration and Functions: ZXU/ Functions: Functions: D, PW, or Absolute Maximum ESD Recommended Operating Thermal Information: ZXU, YZT, and Thermal Information: D, PW, and Electrical Timing Requirements: VCCA = V Timing Requirements: VCCA = V Timing Requirements: VCCA = V Switching Characteristics: VCCA = V Switching Characteristics: VCCA = V Switching Characteristics: VCCA = V Typical Parameter Measurement Load Voltage Detailed Functional Block Feature Device Functional Application and Application Typical Power Supply Layout Layout Device and Documentation Documentation Receiving Notification of Documentation Community Receiving Notification of Documentation Support Electrostatic Discharge Mechanical, Packaging, and Revision HistoryNOTE: Page numbers for previous revisions may differ from page numbers in the current from Revision H (May 2018) to Revision I (October 2020)Page Updated the numbering format for tables, figures, and cross-references throughout the document.

4 1 Added NMN Package 12-Pin from Revision G (September 2017) to Revision H (May 2018)Page Changed maximum values for maximum data rate within Switching Characteristics: VCCA = V Vtable ..14 Changes from Revision F (December 2014) to Revision G (September 2017)Page Changed Device Information Deleted GXU references Added Junction temperature in the Absolute Maximum Ratings ..7 Reformatted Electrical Characteristics ..9 Added Basics of Voltage Translation to Related Added Receiving Notification of Documentation Updates and Community Resources ..24 Changes from Revision E (August 2013) to Revision F (December 2014)Page Added Pin Configuration and Functions section, Handling Rating table, Feature Description section, DeviceFunctional Modes, Application and Implementation section, Power Supply Recommendations section, Layoutsection, Device and Documentation Support section, and Mechanical, Packaging, and Orderable Informationsection.

5 1 Deleted the Package thermal impedance information from the Absolute max ratings table into the ThermalInformation table. Moved the Tstg row into the new Handling Ratings table..7 TXS0104 ESCES651I JUNE 2006 REVISED OCTOBER Document FeedbackCopyright 2020 Texas Instruments IncorporatedProduct Folder Links: TXS0104E Changed the last 2 rows of MIN MAX (24 MAX and 2 MAX) to the MIN columns, in the first switchingcharacteristics table ..11 Changes from Revision D (May 2008) to Revision E (August 2013)Page Deleted the ordering table .. JUNE 2006 REVISED OCTOBER 2020 Copyright 2020 Texas Instruments IncorporatedSubmit Document Feedback3 Product Folder Links: TXS0104E5 Pin Configuration and Functions4321A B CFigure 5-1. ZXU Package 12-Pin MICROSTARJUNIOR Top View4321A B CFigure 5-2.

6 NMN Package 12-Pin nFBGA Top ViewPin Functions: ZXU/ A1. Referenced to A2. Referenced to A3. Referenced to A4. Referenced to B1. Referenced to B2. Referenced to B3. Referenced to B4. Referenced to GroundOEB3I3-state output-mode enable. Pull OE low to place all outputs in 3-state mode. Referencedto A-port supply voltage. V VCCA V and VCCA B-port supply voltage. V VCCB JUNE 2006 REVISED OCTOBER Document FeedbackCopyright 2020 Texas Instruments IncorporatedProduct Folder Links: TXS0104 EDCBA3 21 Figure 5-3. YZT Package 12-Pin DSBGA Top ViewPin Functions: A1. Referenced to A2. Referenced to A3. Referenced to A4. Referenced to B1. Referenced to B2. Referenced to B3. Referenced to B4.

7 Referenced to GroundOEC2I3-state output-mode enable. Pull OE low to place all outputs in 3-state mode. Referencedto A-port supply voltage. V VCCA V and VCCA B-port supply voltage. V VCCB JUNE 2006 REVISED OCTOBER 2020 Copyright 2020 Texas Instruments IncorporatedSubmit Document Feedback5 Product Folder Links: TXS0104E1147823456131211109B1B2B3B4 NCA1A2A3A4 NCOEVGNDCCBVCCANC - No internal connectionFigure 5-4. RGY Package 14-Pin VQFN Top View1413121110981234567 OEGNDNCA4A3A2 VCCANCB4B3B2B1 VCCBA1NC - No internal connectionFigure 5-5. D and PW Package 14-Pin SOIC andTSSOP Top ViewPin Functions: D, PW, or A1. Referenced to A2. Referenced to A3. Referenced to A4. Referenced to B1. Referenced to B2.

8 Referenced to B3. Referenced to B4. Referenced to GroundOE8I3-state output-mode enable. Pull OE low to place all outputs in 3-state mode. Referencedto A-port supply voltage. V VCCA V and VCCA B-port supply voltage. V VCCB For the RGY package, the exposed center thermal pad must be connected to groundTXS0104 ESCES651I JUNE 2006 REVISED OCTOBER Document FeedbackCopyright 2020 Texas Instruments IncorporatedProduct Folder Links: TXS0104E6 Absolute Maximum Ratingsover operating free-air temperature range (unless otherwise noted)(1)MINMAXUNITS upply voltage, VCCA voltage, VCCB voltage, VI (2)A port port range applied to any output in the high-impedance or power-off state, VO (2)A port port range applied to any output in the high or low state, VO (2) (3)A port + port + clamp current, IIKVI < 0 50mAOutput clamp current, IOKVO < 0 50mAContinuous output current, IO 5050mAContinuous current through each VCCA, VCCB, or GND 100100mAOperating junction temperature, TJ150 CStorage temperature, TSTG 65150 C(1) Stresses beyond those listed under Absolute Maximum Ratings may cause permanent damage to the device.

9 These are stress ratingsonly, and functional operation of the device at these or any other conditions beyond those indicated under Recommended OperatingConditions is not implied. Exposure to absolute-maximum-rated conditions for extended periods may affect device reliability.(2) The input and output negative-voltage ratings may be exceeded if the input and output current ratings are observed.(3) The value of VCCA and VCCB are provided in the recommended operating conditions ESD RatingsVALUEUNITV(ESD)Electrostatic dischargeHuman body model (HBM), per ANSI/ESDA/JEDECJS-001, all pins(1)A Port 2000VB Port 15kVCharged device model (CDM), per JEDEC specificationJESD22-C101, all pins(2)A Port 1000VB Port 1000 Machine model (MM)A Port 200VB Port 200(1) JEDEC document JEP155 states that 500-V HBM allows safe manufacturing with a standard ESD control process.

10 (2) JEDEC document JEP157 states that 250-V CDM allows safe manufacturing with a standard ESD control JUNE 2006 REVISED OCTOBER 2020 Copyright 2020 Texas Instruments IncorporatedSubmit Document Feedback7 Product Folder Links: Recommended Operating Conditionsover operating free-air temperature range (unless otherwise noted)(1) (2)VCCAVCCBMINMAXUNITVCCAS upply voltage(3) voltage(3) input voltageA-port V to V to VVCCI V to V to VVCCI V to V to VVCCI V to V to VVCCA input voltageA-port V to V to V to V to V to V to V0 VCCA t/ vInput transitionrise or fall rateA-port V to V to V10ns/VB-port V to V to V10 Control V to V to V10 TAOperating free-air temperature 4085 C(1) VCCI is the supply voltage associated with the input port.