Curiosity Nano Hardware User Guide - Microchip Technology
3.1.2 Virtual Serial Port (CDC) The virtual serial port (CDC) is a general purpose serial bridge between a host PC and a target device. 3.1.2.1 Overview The on-board debugger implements a composite USB device that includes a standard Communications Device Class (CDC) interface, which appears on the host as a virtual serial port.
Download Curiosity Nano Hardware User Guide - Microchip Technology
Information
Domain:
Source:
Link to this page:
Documents from same domain
Power Factor Correction in Power Conversion …
ww1.microchip.com© 2007 Microchip Technology Inc. DS01106A-page 2 AN1106 FIGURE 1: CURRENT WAVEFORMS WITH AND WITHOUT PFC These waveforms illustrate that …
2.7V to 5.5V Single Supply CMOS Op Amp
ww1.microchip.comMCP601/1R/2/3/4 DS21314G-page 2 © 2007 Microchip Technology Inc. 1.0 ELECTRICAL CHARACTERISTICS Absolute Maximum Ratings † VDD –VSS.....7.0V
Data Encryption Routines for PIC24 and dsPIC Device
ww1.microchip.com© 2006 Microchip Technology Inc. DS01044A-page 1 AN1044 INTRODUCTION Currently, there are three data encryption standards approved …
Using SAM-BA for Linux on SAMA5D3 Xplained
ww1.microchip.comAN-8995 – Using SAM-BA for Linux on SAMA5D3 Xplained: 42328A−06/2014 Page 5 of 19 2. Setup With Ubuntu distributions, a user has to be member of the dialout group to access serial devices like
MCP6021/1R/2/3/4 - Rail-to-Rail Input/Output, 10 …
ww1.microchip.com2001-2017 Microchip Technology Inc. DS20001685E-page 1 MCP6021/1R/2/3/4 Features • Rail-to-Rail Input/Output • Wide Bandwidth: 10 MHz (typical)
Low Quiescent Current LDO - Microchip Technology
ww1.microchip.com2005-2016 Microchip Technology Inc. DS20001826D-page 1 MCP1700 Features: • 1.6 µA Typical Quiescent Current • Input Operating Voltage Range: 2.3V to 6.0V
MCP1703 250 mA, 16V, Low Quiescent Current
ww1.microchip.com2010 Microchip Technology Inc. DS22049E-page 1 MCP1703 Features: • 2.0 µA Typical Quiescent Current • Input Operating Voltage Range: 2.7V to16.0V
MTCH6102 Low-Power Projected Capacitive Touch …
ww1.microchip.com2014 Microchip Technology Inc. DS40001750A-page 1 Description: Microchip’s MTCH6102 is a turnkey projected capacitive touch controller that simplifies adding
PIC32 GUI Development Board with Projected …
ww1.microchip.comPIC32 GUI Development Board with Projected Capacitance (PCAP) Touch Information Sheet Microchip Technology Inc.
RN4020 Bluetooth Low Energy Module User’s Guide
ww1.microchip.comRN4020 BLUETOOTH LOW ENERGY MODULE USER’S GUIDE 2014 Microchip Technology Inc. DS70005191B-page 7 Preface INTRODUCTION This chapter contains general information that will be useful to know before using the
Related documents
Universal Serial Bus Specification
esd.cs.ucr.eduUniversal Serial Bus Specification Revision 1.1 ii Scope of this Revision The 1.1 revision of the specification is intended for product design. Every attempt has been made to ensure a
Serial Configuration (EPCS) Devices Datasheet
www.intel.comSerial Configuration (EPCS) Devices Datasheet. This datasheet describes serial configuration (EPCS) devices. Supported Devices. Table . 1 lists the supported Altera ... Additional programming support with the APU and programming hardware from BP Microsystems, System General, and other vendors ...
DATASHEET BLUETOOTH TO SERIAL PORT MODULE HC05
www.electronica60norte.comBLUETOOTH TO SERIAL PORT MODULE HC05 Overview HC‐05 module is an easy to use Bluetooth SPP (Serial Port Protocol) module, designed for transparent wireless serial connection setup. Serial port Bluetooth module is fully qualified Bluetooth V2.0+EDR (Enhanced Data Rate) 3Mbps Modulation with complete 2.4GHz radio transceiver and baseband.
2-Wire Serial EEPROM AT24C32 AT24C64 - Microchip …
ww1.microchip.comSERIAL DATA (SDA): The SDA pin is bidirectional for serial data transfer. This pin is open-drain driven and may be wire-ORed with any number of other open-drain or open collector devices. DEVICE/PAGE ADDRESSES (A2, A1, A0): The A2, A1 and A0 pins are device address inputs that are hard wired or left not connected for hardware compatibility with ...
NI Serial Hardware Specifications and Features Guide ...
www.ni.comNI Serial Hardware Specifications and Features Guide Serial Hardware Features To determine which features your product supports, refer to the following table. Table 7. Serial Hardware Features Hardware Adjustable FIFO Settings Get Interface Type RS-485 Transceiver Control RS-485 Socketed Bias Resistors RS-485 Program-matically Controlled Bias ...
Programmable Serial Channel 8-bit Microcontroller
www.keil.comserial port and interrupt system to continue functioning. The Power-down Mode saves the RAM contents but freezes the oscillator disabling all other chip functions until the next hardware reset. Pin Description VCC Supply voltage. GND Ground. Port 0 Port 0 is an 8-bit open-drain bi-directional I/O port. As an output port, each pin can sink eight ...
AN0046: USB Hardware Design Guidelines - Silicon Labs
www.silabs.comHardware Design Considerations and AN0016 Oscillator Design Considerations, and it is recommended to follow these guidelines as ... • Terminate D+ and D- with 15 ohm serial resistors. Place near EFM32. • Use an ESD protection device. Place near USB receptacle. • Select a USB Series A type receptacle.
SIM800L Hardware Design V1 - FilipeFlop
www.filipeflop.comThis document contains proprietary technical information which is the property of SIMCom Limited, copying of this document and giving it to others and the using or communication of the contents thereof, are forbidden