H-Bridge Gate Driver IC - NXP
gate driver channels are independently controlled by four separate input pins, thus ... High-Side Source Current from CP_OUT in Switch ON State IS 250 mA High-Side Gate Voltage VGATE_HS –0.3 to 65 V ... VCC2 can sustain load dump pulse of 40 V, 400 ms, 2.0 Ω. [2] In case of high current (SRC_HS >100 mA) and high voltage (>20 V) between GATE ...
Download H-Bridge Gate Driver IC - NXP
Information
Domain:
Source:
Link to this page:
Documents from same domain
AN10441 Level shifting techniques in I2C-bus design
www.nxp.comDocument information AN10441 Level shifting techniques in I2C-bus design Rev. 01 — 18 June 2007 Application note Info Content Keywords I2C-bus, level shifting Abstract Logic level shifting may be required when interfacing legacy devices with
AN3234: Washing Machine Three-Phase AC …
www.nxp.comWashing Machine Three-Phase AC Induction Motor Drive, Rev. 0 Indirect Vector Control 4 Freescale Semiconductor If you are looking for more theory on the field ...
1. General description - nxp.com
www.nxp.com1. General description The TJA1044 is part of the Mantis family of high-speed CAN transceivers. It provides an interface between a Controller Area Network (CAN) protocol controller and the physical
PCA9570 Remote 4-bit general purpose outputs for 1 MHz …
www.nxp.com1. General description The PCA9570 is a CMOS device that provides 4 bits of General Purpose parallel Output (GPO) expansion in low voltage processor and handheld battery powered mobile
P82B96 Dual bidirectional bus buffer - nxp.com
www.nxp.com1. General description The P82B96 is a bipolar IC that creates a non-latching, bidirectional, logic interface between the normal I2C-bus and a range of other bus configurations.It can interface
S32K144 EVB Quick Start Guide - NXP Semiconductors
www.nxp.comJ14 SWD connector. 3 EXTERNAL USE S32K144 EVBFeatures: ... USB connector of the USB cable to micro-B port J7 on the S32K144EVB. ... Windows, Linux and Mac operating systems. Using the MSD Flash Programmer 1. Locate the .srec file of your project , file is under the
Three-Phase BLDC Motor Sensorless Control Using …
www.nxp.comThis document describes the design of a three-phase brushless DC motor (BLDC motor) drive based on Freescale’s MC56F8013 and MC56F8023 dedicated motor control device. Brushless DC motors are popular in a wide application area.
AN11443 BFU550XR ISM 433 MHz LNA design - nxp.com
www.nxp.comAN11443 BFU550XR ISM 433 MHz LNA design Rev. 1 — 23 January 2014 Application note . Document information Info Content Keywords BFU520, BFU530, BFU550 series, ISM-band, 433MHz 866MHz Abstract This document describes an ISM Frequency LNA design on BFU5xxXR Starter kit
DSP56156 16-Bit Digital Signal Processor - nxp.com
www.nxp.comThe DSP56156 is a general-purpose MPU-style Digital Signal Processor (DSP). On a single semi- conductor chip, the DSP56156 comprises a very efficient 16-bit digital signal processing core, pro-
SAA7706H Car radio Digital Signal Processor (DSP)
www.nxp.comCar radio Digital Signal Processor (DSP) SAA7706H This text is here in white to force landscape pages to be rotated correctly when browsing through the pdf in the Acrobat reader.This text is here in _white to force landscape pages to be rotated correctly when browsing through the pdf in the Acrobat reader.This text is here inThis text is here in
Related documents
UNDERSTANDING RELAYS - Autoshop 101
autoshop101.comRelays are remote control electrical switches that are controlled by another switch, such as a horn switch or a computer as in a power train control module. Relays allow a small current flow circuit to control a higher current circuit. Several designs of relays are in use today, 3-pin, 4-pin, 5-pin, and 6-pin, single switch or dual switches.
NCP380 - Fixed/Adjustable Current‐Limiting Power ...
www.onsemi.compower-switch if the output voltage is higher than the input voltage to protect devices on the input side of the switch. The FLAG logic output asserts low during over current, reverse-voltage or over temperature conditions. The switch is controlled by a logic enable input active high or low. Features • 2.5 V – 5.5 V Operating Range
Fundamentals of motor control - STMicroelectronics
www.st.comWhen the low side switch is ON, the load’s current flows through the resistor positioned in-between the low side and the ground ... • The motor is controlled applying a voltage on the motor leads. The higher the voltage, the higher the speed. The direction is changed reversing the polarity on the leads.
DIRECTV Universal Remote Control User’s Guide
www.att.comswitch under AV1, AV2 or TV to select the compo-nent you want to control. A green LED under the switch position will con-firm the component being controlled. Press TV INPUTto select the available inputs on your TV. (Note: Additional program-ming is required to activate the TV INPUT key. See instructions on page 11).
RadioRA 2 Maestro Local Controls SPEC (369225)
www.lutron.com4 Power Boosters / Load Interfaces: -6ND, -10ND, -6NA can be used to control power boosters / load interfaces. For a list of compatible power boosters / load interfaces see Compatible Power Boosters and Load Interfaces, page 11. 5 Minimum load depends on lamp and is not limited to a particular wattage. Refer to the LED Product Selection Tool at
Cisco SRW224P 24-Port 10/100 + 2-Port Gigabit Switch ...
www.cisco.comThe Cisco ® SRW224P 24-Port 10/100 + 2-Port Gigabit Switch (Figure 1) offers a highly secure way to expand your network. Web-based configuration of the switch is secured using SSL. User access is verified using 802.1X security with a RADIUS authentication mechanism and can also be controlled using MAC-based filtering.
Overview - Switch Pros
switchpros.comSP9100 8-Switch Programmable Switch Panel Power System ... To figure out the current draw of a load rated in watts, simply divide power rating of the accessory by the operating ... The other option is to program individual switches to be “battery controlled”. When “battery controlled,” the switches will operate at all times.
28 V, 56 mΩ, Load Switch with Programmable Current Limit ...
www.vishay.comthe SiP32419, the switch will remain off and the fault flag will remain on. The switch will be reset by toggling either control signal on EN pin or the input power if it is not under over temperature fault condition. These devices feature a low voltage control logic interface which can be controlled without the need for level shifting.