High-voltage resonant controller
The IC enables the designer to set the operating frequency range of the converter by means of an externally programmable oscillator. At start-up, to prevent uncontrolled inrush current, the switching frequency starts from a programmable maximum value and progressively decays until it reaches the steady-state value determined by the control loop.
Download High-voltage resonant controller
Information
Domain:
Source:
Link to this page:
Documents from same domain
Low-power dual operational amplifier - st.com
www.st.comFebruary 2016 DocID2471 Rev 17 1/24 This is information on a product in full production. www.st.com LM2904, LM2904A Low-power dual operational amplifier
AN3128 Application note - st.com
www.st.comJune 2011 Doc ID 16918 Rev 5 1/105 AN3128 Application note STM32 embedded graphic objects/touchscreen library Introduction This library is a firmware package which contains a collection of routines, data structures,
AN4767 Application note - st.com
www.st.comDocID028380 Rev 2 7/16 AN4767 Dual bank use cases 15 With dual bank, all the manipulation with the other bank is just another task of the main program.
AN3155 Application note - st.com
www.st.comOctober 2016 DocID17066 Rev 7 1/37 1 AN3155 Application note USART protocol used in the STM32 bootloader Introduction This application note describes the USART protocol used in the STM32 microcontroller
USB Power Delivery and Type-C - st.com
www.st.comUSB Type -C Overview USB Power Delivery specification introduces USB Type-C receptacle, plug and cable; they provide a smaller, thinner and more robust alternative to existing USB interconnect.
Datasheet - L78 - Positive voltage regulator ICs - …
www.st.comTO- 2 2 0 TO-2 2 0 F P DPAK D² PAK Features • Output current up to 1.5 A • Output voltages of 5; 6; 8; 8.5; 9; 12; 15; 18; 24 V • Thermal overload protection
AN2867 Application note - st.com
www.st.comMay 2017 DocID15287 Rev 11 1/43 1 AN2867 Application note Oscillator design guide for STM8AF/AL/S and STM32 microcontrollers Introduction Many designers know oscillators based on Pierce-Gate topology (hereinafter referred to as
AN4776 Application note - st.com
www.st.comMay 2017 DocID028459 Rev 2 1/73 1 AN4776 Application note General-purpose timer cookbook Introduction The timer peripheral is part of …
120-volt, 100-watt, DMOS audio amplifier with mute …
www.st.comSeptember 2010 Doc ID 6744 Rev 8 1/21 21 TDA7293 120-volt, 100-watt, DMOS audio amplifier with mute and standby Features Multipower BCD technology Very high operating voltage range (±50 V)
Electronic transformer for a 12V halogen lamp - …
www.st.comAPPLICATION NOTE AN528/0999 1/4 ELECTRONIC TRANSFORMER FOR A 12V HALOGEN LAMP by P. Fichera, R. Scollo 1. INTRODUCTION Lighting that uses halogen lamps is commonly found
Related documents
Snubber Circuits Suppress Voltage Transient Spikes in ...
pdfserv.maximintegrated.comloop due to (dv/dt) induced spurious turn-on of the MOSFET as a result of the transient voltage spike. Secondary Leakage Inductance and the Rectifier Diode The transformer secondary leakage inductance may couple with the reverse recovery current IREC of the output rectifier diode to cause ringing when the diode turns off.
AN149 Modeling and Loop Compensation Design of …
www.analog.comSince the current and voltage sources are the products of two variables, the system is still a nonlinear system. SmAll SIgnAl modelIng of PWm ConVerter PoWer StAge A switching mode power supply (SMPS), such as the buck step-down converter in Figure 4, usually has two operating modes, depending on the on/off state of its main control switch.
Building a DC-DC Step-Down (Buck) Converter Circuit Using ...
www.egr.msu.eduThe primary objective is to build a simple circuit of DC-DC stepping-down (Buck) converter. With the LM7809 positive voltage regulator, it is expected to have about 11V-17V DC input stepping-down to 9V DC output. And the secondary objective is to be able to achieve output voltage that is stabilized at its level.
TDA8954 2 × 210 W class-D power amplifier - NXP
www.nxp.compop noise-free start-up. The bias-current setting of the (VI converter) input stages is related to the voltage on the MODE pin. In Mute mode, the bias-current setting of the VI converters is zero (VI converters are disabled). In Operating mode, the bias current is …
Zero Voltage Switching Resonant Power Conversion
www.ti.comvalue L, and the magnetizing current ML., as well as the inductor’s DC resistance is negligi-ble. In addition, both the input voltage VjN and output voltage V. are purely DC, and do not vary during a given conversion cycle. Last, the converter is operating in a closed loop configu-ration which regulates the output voltage V. .
LM5164 100-V Input, 1-A synchronous buck DC/DC converter ...
www.ti.comLM5164 100-V Input, 1-A synchronous buck DC/DC converter with ultra-low IQ 1 1 Features 1• Designed for reliable and rugged applications – Wide input voltage range of 6 V to 100 V – Junction temperature range: –40°C to +150°C – Fixed 3-ms internal soft-start timer – Peak and valley current-limit protection