Installation Guide
The LED fits into a 9/32-inch mounting hole. Be sure to check for clearance prior to drilling the mounting hole. NOTE: Never use a BLUE LED in combination with a RED LED. IMPORTANT! The door lock outputs are low current and should not be attached directly to any high current device; they are only to be used to activate relays
Download Installation Guide
Information
Domain:
Source:
Link to this page:
Documents from same domain
Installation Guide - directeddealers.com
www.directeddealers.comThis product is intended for installation by a professional installer only! Attempts to install this product by a per-son other than a trained professional may result in severe
556H Honda/Acura Immobilizer Bypass Module
www.directeddealers.com© 2004 Directed Electronics, Inc. Vista, CA N556H 10/04 1 556H Honda/Acura Immobilizer Bypass Module Mode 1 Mode 2 Honda Accord 2003-2004 Honda Accord 1998-2002 Honda CRV 2002-2004 Honda CRV 1998-2001
Valet switch Button Control Center LED Quick …
www.directeddealers.com© 2012 Directed. All rights Reserved. 1 Quick Reference Install Guide Automate 4104A 1-Way Supercode + _ Neutral Safety Switch D2D Port (for …
Security and Remote Start Remote Start Keyless …
www.directeddealers.comRemote Start Keyless Entry Quick Reference Wiring Guide RS in Valet Program switch input (use Blue two-pin from antenna cable) D2D …
Vista, CA 92081 OWNER’S GUIDE 4214A 4114A
www.directeddealers.comCongratulations Congratulations on the purchase of your state-of-the-art remote start and keyless entry system. Reading this Owner’s Guide prior to using your
MODEL Vista, CA 92081 OWNER'S GUIDE 4204A
www.directeddealers.comCongratulations Congratulations on the purchase of your state-of-the-art remote start and keyless entry system. Reading this Owner’s Guide prior to using
Responder LC Model 5901 Security and Remote …
www.directeddealers.comResponder LC Model 5901 Security and Remote Start Installation Guide This product is intended for installation by a professional installer only!
Responder HD, LCD, LED and 1-way Models: 5906, …
www.directeddealers.comResponder HD, LCD, LED and 1-way Models: 5906, 5706, 5806 and 5606 Security and Remote Start Installation Guide This product is intended for installation by a professional
N4103 2008-07 web - directeddealers.com
www.directeddealers.comModel 4103 Installation Guide NOTE: This product is intended for installation by a profes- sional installer only! Any attempt to install this product by any person other than a trained professional may result in severe
Valet switch Control button LED Status LED Quick …
www.directeddealers.com© 2009 Directed Electronics. All rights Reserved. 2 QRN4102 2010-01 Programming System Features The System Features Learn Routine dictates how the unit operates.
Related documents
Future Technology Devices International Ltd FT234XD
www.ftdichip.comfor USB driver development in most cases. Configurable CBUS I/O pin . Transmit and receive LED drive signals. UART interface support for 7 or 8 data bits, 1 or 2 stop bits and odd / even / mark / space / no parity Synchronous and asynchronous bit bang interface options with RD# and WR# strobes. (3mm x 3mm) RoHS compliant.
Data Sheet
cdn.sparkfun.com3 LDR LED driver input for proximity IR LED, constant current source LED driver 4 LEDK LED Cathode, connect to LDR pin when using internal LED driver circuit 5 LEDA LED Anode, connect to VLEDA on PCB 6 GND Power supply ground. All voltages are referenced to GND 7 SCL I I2C serial clock input terminal - clock signal for I2C serial data
HV9910B Data Sheet
ww1.microchip.comJan 27, 2015 · • DC/DC or AC/DC LED driver applications • RGB backlighting LED driver • Back lighting of flat panel displays • General purpose constant current source • Signage and decorative LED lighting • Chargers Description HV9910B is an open loop, current mode control, LED driver IC. This IC can be programmed to operate in either a constant ...
1-Way System) 2-Way Paging System REMOTE START SYSTEM
www.crimestopper.comConnect to the LOW CURRENT Negative Horn Trigger wire usually located near the steering column. If the vehicle horn circuit requires 12V, then a relay is required. RELAY WIRING: Connect the Yellow wire to terminal #85, connect relay terminals #86 and #87 to 12V constant power. Connect terminal #30 to the 12V positive Horn activation wire.
LED應用與驅動方式 - National Sun Yat-sen University
www.ee.nsysu.edu.twFeatures of SiTI LED Driver Current Adjustment – Constant Current Adjusted by External Resistor – Global Brightness Control – Dot Correction Adjustment – PWM Gray Scale Adjustment High Power Driving – 500mA+ per Channel – 17V / 36V of Output Low Power Supply Voltage – 3.3V~33V Protection Circuitry – Open/Short Detection ...
High Performance Perimeter Slot (HP-WS)
www.finelite.comSTATIC WHITE DRIVER: Replaceable 120V, 277V, and 347V constant current reduction dimming driver standard. Can be wired dimming or non-dimming. 0-10V dimming controls with a range of 100%-10% stan-dard. Dimming to 1% available. Separate dimming for uplight and down-light available. Driver is fully accessible from below the ceiling. - Power ...
CAT4016 - 16-Channel Constant Current LED Driver
www.onsemi.comThe CAT4016 is a 16 channel constant current driver for LED billboard and other general display applications. LED channel currents are programmed together via an external RSET resistor. Low output voltage operation on the LED channels as low as 0.4 V (for 2 to 100 mA LED current) allows for more power efficient designs.