Example: bachelor of science
HV9910B Data Sheet
Jan 27, 2015 · • DC/DC or AC/DC LED driver applications • RGB backlighting LED driver • Back lighting of flat panel displays • General purpose constant current source • Signage and decorative LED lighting • Chargers Description HV9910B is an open loop, current mode control, LED driver IC. This IC can be programmed to operate in either a constant ...
Tags:
Information
Domain:
Source:
Link to this page:
Documents from same domain
MCP1703 250 mA, 16V, Low Quiescent Current
ww1.microchip.com2010 Microchip Technology Inc. DS22049E-page 1 MCP1703 Features: • 2.0 µA Typical Quiescent Current • Input Operating Voltage Range: 2.7V to16.0V
Low Quiescent Current LDO - Microchip Technology
ww1.microchip.com2005-2016 Microchip Technology Inc. DS20001826D-page 1 MCP1700 Features: • 1.6 µA Typical Quiescent Current • Input Operating Voltage Range: 2.3V to 6.0V
Power Factor Correction in Power Conversion …
ww1.microchip.com© 2007 Microchip Technology Inc. DS01106A-page 2 AN1106 FIGURE 1: CURRENT WAVEFORMS WITH AND WITHOUT PFC These waveforms illustrate that …
Data Encryption Routines for PIC24 and dsPIC Device
ww1.microchip.com© 2006 Microchip Technology Inc. DS01044A-page 1 AN1044 INTRODUCTION Currently, there are three data encryption standards approved …
2.7V to 5.5V Single Supply CMOS Op Amp
ww1.microchip.comMCP601/1R/2/3/4 DS21314G-page 2 © 2007 Microchip Technology Inc. 1.0 ELECTRICAL CHARACTERISTICS Absolute Maximum Ratings † VDD –VSS.....7.0V
Using SAM-BA for Linux on SAMA5D3 Xplained
ww1.microchip.comAN-8995 – Using SAM-BA for Linux on SAMA5D3 Xplained: 42328A−06/2014 Page 5 of 19 2. Setup With Ubuntu distributions, a user has to be member of the dialout group to access serial devices like
MCP6021/1R/2/3/4 - Rail-to-Rail Input/Output, 10 …
ww1.microchip.com2001-2017 Microchip Technology Inc. DS20001685E-page 1 MCP6021/1R/2/3/4 Features • Rail-to-Rail Input/Output • Wide Bandwidth: 10 MHz (typical)
MTCH6102 Low-Power Projected Capacitive Touch …
ww1.microchip.com2014 Microchip Technology Inc. DS40001750A-page 1 Description: Microchip’s MTCH6102 is a turnkey projected capacitive touch controller that simplifies adding
PIC32 GUI Development Board with Projected …
ww1.microchip.comPIC32 GUI Development Board with Projected Capacitance (PCAP) Touch Information Sheet Microchip Technology Inc.
RN4020 Bluetooth Low Energy Module User’s Guide
ww1.microchip.comRN4020 BLUETOOTH LOW ENERGY MODULE USER’S GUIDE 2014 Microchip Technology Inc. DS70005191B-page 7 Preface INTRODUCTION This chapter contains general information that will be useful to know before using the
Related documents
CAT4016 - 16-Channel Constant Current LED Driver
www.onsemi.comThe CAT4016 is a 16 channel constant current driver for LED billboard and other general display applications. LED channel currents are programmed together via an external RSET resistor. Low output voltage operation on the LED channels as low as 0.4 V (for 2 to 100 mA LED current) allows for more power efficient designs.
LED應用與驅動方式 - National Sun Yat-sen University
www.ee.nsysu.edu.twFeatures of SiTI LED Driver Current Adjustment – Constant Current Adjusted by External Resistor – Global Brightness Control – Dot Correction Adjustment – PWM Gray Scale Adjustment High Power Driving – 500mA+ per Channel – 17V / 36V of Output Low Power Supply Voltage – 3.3V~33V Protection Circuitry – Open/Short Detection ...
Data Sheet
cdn.sparkfun.com3 LDR LED driver input for proximity IR LED, constant current source LED driver 4 LEDK LED Cathode, connect to LDR pin when using internal LED driver circuit 5 LEDA LED Anode, connect to VLEDA on PCB 6 GND Power supply ground. All voltages are referenced to GND 7 SCL I I2C serial clock input terminal - clock signal for I2C serial data
High Performance Perimeter Slot (HP-WS)
www.finelite.comSTATIC WHITE DRIVER: Replaceable 120V, 277V, and 347V constant current reduction dimming driver standard. Can be wired dimming or non-dimming. 0-10V dimming controls with a range of 100%-10% stan-dard. Dimming to 1% available. Separate dimming for uplight and down-light available. Driver is fully accessible from below the ceiling. - Power ...
1-Way System) 2-Way Paging System REMOTE START SYSTEM
www.crimestopper.comConnect to the LOW CURRENT Negative Horn Trigger wire usually located near the steering column. If the vehicle horn circuit requires 12V, then a relay is required. RELAY WIRING: Connect the Yellow wire to terminal #85, connect relay terminals #86 and #87 to 12V constant power. Connect terminal #30 to the 12V positive Horn activation wire.
Installation Guide
www.directeddealers.comThe LED fits into a 9/32-inch mounting hole. Be sure to check for clearance prior to drilling the mounting hole. NOTE: Never use a BLUE LED in combination with a RED LED. IMPORTANT! The door lock outputs are low current and should not be attached directly to any high current device; they are only to be used to activate relays
Future Technology Devices International Ltd FT234XD
www.ftdichip.comfor USB driver development in most cases. Configurable CBUS I/O pin . Transmit and receive LED drive signals. UART interface support for 7 or 8 data bits, 1 or 2 stop bits and odd / even / mark / space / no parity Synchronous and asynchronous bit bang interface options with RD# and WR# strobes. (3mm x 3mm) RoHS compliant.