INSTALLATION - Huber Engineered Woods
INSTALLATION MANUAL. 2 . ZIP SYSTEM ® SHEATHING AND TAPE . ATTENTION: ... Woods (HEW), local building code, engineer or architect of record or other authority having jurisdiction. You are fully ... METAL ROOFS 49 . CLAY, CONCRETE TILE 50 . SLATE 51 . HUB 81670 REV06/21 INSTALLATION MANUAL 6
Download INSTALLATION - Huber Engineered Woods
Information
Domain:
Source:
Link to this page:
Documents from same domain
ZIP System R Sheathing - Huber Engineered Woods
www.huberwood.comZIP System R Sheathing Installation 04 ZIP System ® R Sheathing Installation Manual Step 3. Fasten the panels to the framing members with code approved fasteners. When used to resist lateral
0 ICC ES Report ESR - Huber Engineered Woods
www.huberwood.comICC-ES Evaluation Reports are not to be construed as representing aesthetics or any other attributes not specifically addressed , nor are they to be construed
Installation Instructions - Huber Engineered Woods
www.huberwood.comInstallation Instructions ComposItIon & materIals Huber Engineered Woods (HEW) is committed to the responsible use of natural resources. AdvanTech® panels are produced from young, fast- growing trees for less waste and faster availability.
ADVANTECH® SHEATHING
www.huberwood.comliterature, test reports, installation instructions, and special applications are available through Huber Engineered Woods. Please visit advantechperforms.com or call 800.933.9220 xt E 2716 to speak to a technical representative.
Installation Manual-ZIP System Sheathing-Wall and Roof
www.huberwood.companels in applications where the wall sheathing is designed to resist combined wind uplift and shear. Do not use in fire-rated assemblies in lieu of a ... framing1, light gauge metal framing2, CMU/concrete walls3 and new or existing OSB and plywood sheathing4. 1: Follow installation requirements in ESR-3373 and the remainder of this report. ...
Contents
www.huberwood.comlaminated with a water-resistive facer on the exterior and a rigid foam insulation panel bonded on the opposite (interior) face. When properly installed andtaped, ZIP System - R-Sheathing provides a water-resistive barrier, air barrier and exterior insulation in one product. It may also be
Related documents
Installation Operation and Maintenance Manual - Greenheck …
content.greenheck.comInstallation Operation and Maintenance Manual ... sheet metal screws. Connect high and low voltage supplies along with fan interlock circuit (if no airflow switch is furnished). Larger heaters may require hangers. Connect high and low voltage supplies as ... generated from the building’s automation system or a
IronRidge Flush Mount Manual
files.ironridge.com• Comply with all applicable local or national building and fire codes, including any that may supersede this manual. ... Standing Seam Metal Roof Clamps - Certification of metal roof clamps includes bonding to both painted and galvalume metal roofs. Tighten S-5! and S-5! Mini set screws to 130-150 in-lbs (≥ 24 gauge) or 160-180 in-lbs (22 ...
Owner’s Manual - Hot Spring Spas
www.hotspring.com(6 mm2) solid copper bonding conductor between this point and any metal equipment, metal water pipe, metal enclosures of electrical equipment, or conduit within five feet (1.5 m) of the unit as needed to comply with local requirements. WARNING: • To reduce the risk of electrical shock, replace a damaged cord immediately.
ROOFING & WALLING INSTALLATION MANUAL - Lysaght
www.lysaght.com2.9 Metal and timber compatibility 7 2.10 Transportation 8 ... site and structural limitations and your building and construction capabilities. This Manual endeavours to present information on products, details, installation and practices in a clearly prescribed manner ... Steel Roofing and Walling: Installation Manual, and
Installation Manual for STANDING ... - Metal Roofing Source
www.metalroofingsource.comInstallation Manual for STANDING SEAM ROOFING Absolute Steel Toll Free 877-833-3237 / Phone 480-768-1618 / Fax 480-768-1514 www.MetalRoofingSource.com
INSTALLATION MANUAL - Metal Roofing Source
www.metalroofingsource.comINSTALLATION OF PANELS ROOF PITCH This style of metal roofing panels requires a certain degree of pitch to ensure proper water drainage. Florida Building Code allows a minimum pitch of 2/12 for Grand Rib-3 panels as long as lap screws and sealant are applied to the laps to prevent water from siphoning over the ribs (see Fig. 5 on p. 4).