MaxiMintegrated Data Sheet
• High SNR -40°C to +85°C Operating Temperature Range Ordering Information appears at end of data sheet. 19-7740; Rev 1; 10/18 PHOTO DIODE LED DRIVERS RED/IR LED PACKAGING HUMAN SUBJECT ELECTRICAL OPTICAL AMBIENT LIGHT 18-BIT CURRENT ADC AMBIENT LIGHT CANCELLATION DIGITAL NOISE CANCELLATION DATA FIFO HOST (AP) DRIVER …
Download MaxiMintegrated Data Sheet
Information
Domain:
Source:
Link to this page:
Documents from same domain
SCAN master - Maxim Integrated
datasheets.maximintegrated.com0D[LP,QWHJUDWHG 5LR5REOHV 6DQ-RVH &$ 86$ Maxim cannot assume responsibility for use of any circuitry other than circuitry entirely embodied in a Maxim product.
A Channel Otpt an Controller - Maxim Integrated
datasheets.maximintegrated.comPin Description (continued) www.maximintegrated.com Maxim Integrated │7 MA31790 6-Channel PWM-utput Fan RPM Controller PIN NAME FUNCTION 9 TACH6
DS2401 Silicon Serial Number - Maxim Integrated
datasheets.maximintegrated.comThis command allows the bus master to read the DS2401-bit family code, unique 48bit serial ’s 8 - number, and 8bit CRC. This command can only be used if there is a single DS2401 on the bus.
Not Recommended for New Designs - Maxim …
datasheets.maximintegrated.comIt is not recommended for new designs. ... compatible with the industry-standard LT1001. ... Precision Operational Amplifier
DS1558 Watchdog Clock with NV RAM Control
datasheets.maximintegrated.comS1 s n, year 2000-compliant (Y2KC), real-time clock/calendar with an RTC alarm, watchdog timer, power-on reset, battery monitor, and NV SRAM controller.
±15kV ESD-Protected, Slew-Rate-Limited, Low …
datasheets.maximintegrated.com±15kV ESD-Protected, Slew-Rate-Limited, Low-Power, RS-485/RS-422 Transceivers SWITCHING CHARACTERISTICS—MAX481E/MAX485E, MAX490E/MAX491E, …
MAX13487E/MAX13488E Half-Duplex RS-485-/RS …
datasheets.maximintegrated.comMAX13487E/MAX13488E Half-Duplex RS-485-/RS-422-Compatible Transceiver with AutoDirection Control www.maximintegrated.com Maxim Integrated | 2 Absolute Maximum Ratings
+12V, 30mA Flash Memory Programming Supply …
datasheets.maximintegrated.comMAX662A _____Detailed Description Operating Principle The MAX662A provides a regulated 12V output voltage at 30mA from a 5V ±5% power supply, making it ideal for flash EEPROM programming applications.
MA1454 Precision Sensor Signal Conditioner with ...
datasheets.maximintegrated.comMA1454 Precision Sensor Signal Conditioner with Overvoltage Protection ˜˜ 19-5945 Rev 0; 6/11 General Description The MAX1454 is a highly integrated analog sensor
M14 Six-Channel Digital Isolator - Maxim Integrated
datasheets.maximintegrated.comMA14850 Six-Channel Digital Isolator Maxim Integrated 6 INSULATION AND SAFETY CHARACTERISTICS Note 2: All units are production tested at TA = +25°C. Specifications over temperature are guaranteed by design.
Related documents
Click MAX30101 High-Sensitivity Pulse Oximeter and Heart ...
datasheets.maximintegrated.comELECTRICAL OPTICAL LIGHT 18-BIT CURRENT ADC AMBIENT LIGHT CANCELLATION DIGITAL NOISE CANCELLATION DATA FIFO HOST (AP) DRIVER I2C HARDWARE FRAMEWORK APPLICATIONS COVER GLASS MAX30101 Click here to ask about the production status of specific part numbers. MAX30101 High-Sensitivity Pulse Oximeter and …
Accelerometer and Gyroscopes Sensors: Operation, …
pdfserv.maximintegrated.comSensitivity (mV/g or LSB/g): sensitivity is a measure of the minimum detectable signal or the change in output electrical signal per change in input mechanical change. This is valid in one frequency only. 3. Voltage noise density (µg/SQRT Hz): voltage noise changes with the inverse square root of the bandwidth.
SENSORS & ACTUATORS
students.iitk.ac.inSuppose the output of a sensor for some physical quantity x(t) is given by f(x(t)): • Linear Model, where • Affine Model, where , Often, ‘a’ is called the proportionality constant, which gives an idea of the sensitivity of the sensor, and ‘b’ denotes the bias. Note: The sensitivity of a sensor is ratio of output value to measured ...
1/2.9’’ FHD CMOS Image Sensor Data Sheet
whycan.comIt provides RAW10 and RAW8 data formats with MIPI and DVP interface. It has a commonly used two-wire serial interface for host to control the operation of the whole sensor. 1.2 Features Standard optical format of 1/2.9 inch 2.8μm*2.8μm Output formats: Raw Bayer 10bit/8bit Power supply requirement: AVDD28: 2.7~2.9V(Typ.2.8V)
Medical Instrumentation
www.egr.msu.eduSensitivity Range Differential or single ended Input Impedance frequency response Accuracy Linearity Reliability Specificity Signal-to-noise ratio stability: temperature, Humidity, pressure, Shock, vibration, Radiation Power requirements, Mounting size, shape Invasive or non-invasive Tissue-sensor Interface requirements Material toxicity
Fiber Optic Sensors: Fundamentals and Applications
www.photonics.comProvides extremely high resolution Noise issues such as phase noise and multimode noise are addressed in the detection schemes • Phase change of a light wave through an optical fiber of original length that has been stretched by a length ? Intensity versus relative phase shifts due to constructive and destructive interference • • φ+∆φ ...
IMX385LQR
www.sony-semicon.co.jpHigh sensitivity characteristics using a new-generation 3.75 μm pixel ... Sony's high performance CMOS image sensor with high-speed processing, low noise and low power dissipation by using ... This function uses a method that outputs the data for three frames with different storage times line by line instead of
The Fundamentals of Camera and Image Sensor Technology
www.visiononline.orgAug 10, 2012 · High Bit Depth Considerations With more bits, you get a more accurate measurement of the light. (8, 10, 12 bits = 256, 1024, 4096 grey scales) With more bits, you also have more data to transfer, process, store (12 bit = 50% more data more than 8 bit). Analog and Digital Concepts