Module 4: DC-DC Converters
The principle of step down operation of DC-DC converter is explained using the circuit shown in Figure 3a. When the switch S 1 is closed for time duration T 1, the input voltage V in appears across the load. For the time duration T 2 is switch remains open and the voltage across the load is zero. The waveforms of the output voltage across the ...
Download Module 4: DC-DC Converters
Information
Domain:
Source:
Link to this page:
Documents from same domain
Download Free Lecture Notes-Pdf Link-I
nptel.ac.inenter or leave the system, the extensive state of the system is rendered fixed along with the intensive variables. Therefore, apart from the
L-2 TB ET EE NPTEL
nptel.ac.inChapter 2 Generation, Transmission and Distribution of Electric Power (Lesson-2) 2.1 Goals of the lesson After going through the lesson you shall get a broad idea of the following:
DIRECTIONAL CONTROL VALVES - NPTEL
nptel.ac.in7 Solenoid operated Pilot operated Manual operated Push button Foot operated Pilot-operated solenoid Two-position detent Spring return 1.4 Check Valve
Lecture 7 Aromatic Production - NPTEL
nptel.ac.in353 LECTURE 7 AROMATIC PRODUCTION Aromatic hydrocarbons especially benzene, toluene, xylene, ethyl benzene are major feedstock for a large number of intermediates which are used in the production of synthetic fibers, resins,
Module 8 : Surface Chemistry Lecture 37 : Surface …
nptel.ac.inModule 8 : Surface Chemistry Lecture 37 : Surface Characterization Techniques Objectives After studying this lecture, you will be able to do the following:
Lecture 6 Catalytic Reforming - NPTEL
nptel.ac.in239 6.2. Such rearrangement takes place in reforming reactors in presence of catalyst by way of numerous complex reactions. Table M-VI …
Properties and Applications of Materials - NPTEL
nptel.ac.inProperties and Applications of Materials . ... Properties and typical application of some low carbon and ... Heat treated alloys are stronger but have lower ductility
Reinforced Soil Retaining Walls-Design and …
nptel.ac.inReinforced Soil Retaining Walls-Design and Construction Prof. G L Sivakumar Babu Department of Civil Engineering Indian Institute of Science Bangalore 560012
RESISTOR COMBINATIONS - NPTEL
nptel.ac.inRESISTOR COMBINATIONS • When we do not get specific resistor values we have to either use variable resistors such as potentiometers or presets to …
Chapter 7 Non-linear Seismic Response of Structures
nptel.ac.in238 Chapter 7 Non-linear Seismic Response of Structures . 7.1 Introduction . As per the conventional earthquake-resistant design philosophy, structuresthe are designed
Related documents
ON Semiconductor Is Now
www.onsemi.comA DC/DC Resonant Converter Lr Cr Load Resonant Tank X1 X2 * * * T1 D1 D2 Cout Figure 7. A DC/DC Resonant Converter with Soft ZVS Switching Lr Cr Load Resonant Tank X1 X2 * * * T1 D1 D2 Cout L M To obtain DC voltage, output current of Figure 5 is rectified and stabilized by a large capacitance, providing a
LOAD FLOW STUDY IN POWER SYSTEM
ethesis.nitrkl.ac.inLoad bus: No generator is connected to the bus. At this bus the real and reactive power are specified.it is desired to find out the volatage magnitude and phase angle through load flow solutions.It is required to specify only Pd and Qd at such bus as at a load bus voltage can be allowed to vary within the permissible values.
Lesson 15: Induction Motor Testing: Lock-Rotor and No-load ...
www.engr.siu.eduExample 15-1: Following data is taken from no -load, locked rotor, and DC tests of a 3-phase, wye connected 40 HP, 60 Hz, 460 V, induction motor with a rated current of 57.8 A. The locked -rotor test is made at 15 Hz to minimize the errors due to saturation and skin effects. Determine the motor parameters and the total core,
Chapter 2 Actuators and Drive Systems - MIT OpenCourseWare
ocw.mit.eduand needs a high torque to bear the load. In other words, the impedance of the actuator: m m m angular velocity torque Z ω τ = = (2.2.1) is much smaller than that of the load. τload ωload Joint Axis Gearing Arm Links DC Motor Figure 2.2.1 Joint axis drive system 1 Although a robotic system has multiple axes driven by multiple actuators ...
Electronic Load Fundamentals - White Paper
www.altoo.dkWhen the load connects to a current source, its terminal voltage is equal to the imposed current multiplied by the programmed resistance value. Figure 7 depicts the I-V diagram of an electronic load in CR mode when loading a voltage or current source. A 5 Ω load on a 3 V voltage source will result in a 0.6 A sink current. Alternatively, the same
12ga Load Data Winchester Super Handicap Recipes
www.ballisticproducts.com12ga Load Data Winchester Super Handicap Recipes ® Super Handicap is the same propellant used in Winchester’s Super Handicap ammunition. This slow-burning, high energy propellant gives the shooter great handicap or long range sporting clays loads at up to 1250 fps with a 1-1/8 ounce shot charge. Great velocity with excellent patterns!
Lesson 14: Transfer Functions of Dc Motors
www.engr.siu.edu10/28/2015 5 EXAMPLE 14-1 SOLUTION (2) 9 x c) Find maximum back emf Answer d) Find no-load motor speed At no-load, T=0. Load torque is zero. T=0 TRANSFER FUNCTION OF ARMATURE- CONTROLLED DC MOTOR 10 x Write all variables as time functions
Geotechnical - Load and Resistance Factor Design
www.in.govLoad factor combinations to obtain resulting maximum force effects on the foundations are needed for limit states checks. This is done through structure modeling by varying the load factors over the specified range