MULTISIM TUTORIAL - Michigan Technological University
The ammeter offers advantages over the multimeter for measuring current in a circuit. It takes up less space in a circuit and you can rotate its terminals to suit your layout. Always connect the ammeter in series with the load. To place Ammeter click on View--- Toolbar --- Select Measurement Components. See Figure 17 on how to use the Ammeter.
Download MULTISIM TUTORIAL - Michigan Technological University
Information
Domain:
Source:
Link to this page:
Documents from same domain
R Introduction to Electronics
www.ece.mtu.eduIntroduction to Electronics ii Dedication Human beings are a delightful and complex amalgam of the spiritual, the emotional, the intellectual, and the physical.
EE 3305 Lab 1 Revised 13 Sept 2005
www.ece.mtu.eduEE 3305 Lab 1 Revised 13 Sept 2005 Pre Lab Exercises 1. Read the data sheet for the LM741 Operational Amplifier and fill in the following parameters.
Examples of Ferroresonance in Distribution Systems
www.ece.mtu.edu1 Examples of Ferroresonance in Distribution Systems Roger C. Dugan, Fellow, IEEE Abstract—This is a summary of three different classes of ferroresonance problems commonly encountered on distribution
INTRODUCTION TO LABVIEW - Michigan …
www.ece.mtu.eduINTRODUCTION TO LABVIEW In this lab we are going to understand the fundamentals of labVIEW. We further go on to perform certain experiments using labVIEW simulations.
Re-Introduction to LabVIEW
www.ece.mtu.eduEE 3305 LabVIEW Tutorial Introduction to LabVIEW The program LabVIEW uses the technique of graphical programming. This type of coding is …
Lecture Notes EEE 360 - Michigan Technological University
www.ece.mtu.edu30 Multiply the negative of the fault current by elements in the 3rd column to get the change in voltages 2003 IEEE T & D CONFERENCE Part (ii): Calculate the voltages at bus 2, 3, and 4 during this fault.
Effects of Transient Recovery Voltages on Circuit Breaker ...
www.ece.mtu.eduEffects of Transient Recovery Voltages on Circuit Breaker[1][2][3][6] Transient recovery voltages appear on the system for a very short duration of time and assume very high values.
GE Technical Data of Phase Vacuum Recloser
www.ece.mtu.eduVoltage which appears across the circuit breaker contacts after interruption of fault or interruption of circuit . It consists of the high frequency voltage superimposed on system
Chapter 9 Computer-Based Instrumentation Systems
www.ece.mtu.eduPrinciples and Applications SE OND EDITION Chapter 9 Computer-Based Instrumentation Systems Chapter 9 Computer-Based Instrumentation Systems 1. Describe the operation of the elements of a computer-based instrumentation system. 2. ... Computer-Based Instrumentation Systems Errors in Measurement
Power Grid Analysis with Hierarchical Support Graphs
www.ece.mtu.eduPower Grid Analysis with Hierarchical Support Graphs Xueqian Zhao, Jia Wang, Zhuo Feng, and Shiyan Hu ... DC analysis, power grid is modeled as a network of pure resistors ... DC problem for such a resistive power delivery network with nnodes
Related documents
HID Ballast Testing - Acuity Brands
www.acuitybrandslighting.comHID Ballast Testing 2. HID Short-Circuit Lamp Current To assure the ballast is delivering the proper current under lamp starting conditions, a measurement may be taken by connecting an
TRIUMPH TR2 - TR4A WIRING DIAGRAMS
www.advanceautowire.comtr4 - + starter starter solenoid battery ammeter lighting switch generator generator warning lamp fuse box ignition switch u g g r r r rg w w w rg rg nw ny ng ny heater fan
Section 5 The Charging System - Autoshop 101
www.autoshop101.comSection 5 5-2 TOYOTA Technical Training These components make up the charging system: •Alternator •Voltage regulator •Battery •Charging indicator Charging System Components
CHARGING SYSTEMS - Autoshop 101
www.autoshop101.comToyota Charging Systems Typical charging system components include: IGNITION SWITCH When the ignition switch is in the ON position, battery current energizes the alternator.
Digital Panel Meters AC Ammeter or Voltmeter Type DI3 …
www.carlogavazzisales.comSpecifications are subject to change without notice 3 DI3-72 AV1/AV5 Wiring Diagrams IN+ V IN+ A IN-NC Power supplyIN+ V NC IN+ A IN-NC Power supplyCurrent measurements - direct Current measurements - C.T.
Electron Diffraction - Boston University Physics
physics.bu.eduConnect the multimeter (ammeter) between the anode and the positive side of the high voltage power supply. Set the multimeter to its current scale (mA) and turn it on. Make sure the high voltage supply is set to its minimum. Turn on the power and wait for one minute for the cathode to reach a stable temperature. CONTROLLING THE CURRENT
THE UNIVERSITY OF THE STATE OF NEW YORK • THE STATE ...
www.p12.nysed.govammeter resistor variable resistor lamp Series Circuits I = I 1 = I 2 = I 3 = . . . V = V 1 + V 2 + V 3+ . . . R eq = R 1 + R 2 + R 3 + . . . Parallel Circuits I= 1 + 2 3 + . . . V= 1 2 = . . . = + + + . . . 1 R 3 1 R 2 1 eq R 1 Electricity A = cross-sectional area E = electric field strength F e = electrostatic force I = current k ...
SERVICE MANUAL - Navistar
bodybuilder.navistar.com3200, 4100, 4200, 4300, 4400, 7300, 7400, 7500, 7600, 7700, 8500, 8600, MXT, RXT Models Built Oct. 1, 2005 to Feb. 28, 2007 — ELECTRICAL CIRCUIT DIAGRAMS
Intro to Electricity - Home | NYU Tandon School of Engineering
engineering.nyu.edu• An ammeter measures current • A voltmeter measures the potential difference (voltage) between two points • An ohmmeter measures resistance • A multimeter combines these functions, and possibly some additional ones as well, into a single instrument
CIRCUITS LABORATORY EXPERIMENT 1
classes.engineering.wustl.eduammeter, (4) Measure current by using only a voltmeter and an additional resistor, and (5) Experimentally determine the Thevenin equivalent of a given circuit. 1.3 Theory The digital multimeter (DMM) is a versatile instrument that can be used to make a variety of electrical measurements. The laboratory instrumentation rack at each ...