STM32 microcontroller GPIO configuration for hardware ...
Three-volt tolerant I/O pin TC Three-volt capable I/O pin (Standard 3.3 V I/O) B Dedicated boot pin RST Bidirectional reset pin with embedded weak pull-up resistor Pin functions Alternate functions Functions selected through . GPIOx_AFR. registers Additional functions Functions directly selected and enabled through peripheral registers. 1.
Download STM32 microcontroller GPIO configuration for hardware ...
Information
Domain:
Source:
Link to this page:
Documents from same domain
Low-power dual operational amplifier - st.com
www.st.comFebruary 2016 DocID2471 Rev 17 1/24 This is information on a product in full production. www.st.com LM2904, LM2904A Low-power dual operational amplifier
AN3128 Application note - st.com
www.st.comJune 2011 Doc ID 16918 Rev 5 1/105 AN3128 Application note STM32 embedded graphic objects/touchscreen library Introduction This library is a firmware package which contains a collection of routines, data structures,
AN4767 Application note - st.com
www.st.comDocID028380 Rev 2 7/16 AN4767 Dual bank use cases 15 With dual bank, all the manipulation with the other bank is just another task of the main program.
AN3155 Application note - st.com
www.st.comOctober 2016 DocID17066 Rev 7 1/37 1 AN3155 Application note USART protocol used in the STM32 bootloader Introduction This application note describes the USART protocol used in the STM32 microcontroller
USB Power Delivery and Type-C - st.com
www.st.comUSB Type -C Overview USB Power Delivery specification introduces USB Type-C receptacle, plug and cable; they provide a smaller, thinner and more robust alternative to existing USB interconnect.
Datasheet - L78 - Positive voltage regulator ICs - …
www.st.comTO- 2 2 0 TO-2 2 0 F P DPAK D² PAK Features • Output current up to 1.5 A • Output voltages of 5; 6; 8; 8.5; 9; 12; 15; 18; 24 V • Thermal overload protection
AN2867 Application note - st.com
www.st.comMay 2017 DocID15287 Rev 11 1/43 1 AN2867 Application note Oscillator design guide for STM8AF/AL/S and STM32 microcontrollers Introduction Many designers know oscillators based on Pierce-Gate topology (hereinafter referred to as
AN4776 Application note - st.com
www.st.comMay 2017 DocID028459 Rev 2 1/73 1 AN4776 Application note General-purpose timer cookbook Introduction The timer peripheral is part of …
120-volt, 100-watt, DMOS audio amplifier with mute …
www.st.comSeptember 2010 Doc ID 6744 Rev 8 1/21 21 TDA7293 120-volt, 100-watt, DMOS audio amplifier with mute and standby Features Multipower BCD technology Very high operating voltage range (±50 V)
Electronic transformer for a 12V halogen lamp - …
www.st.comAPPLICATION NOTE AN528/0999 1/4 ELECTRONIC TRANSFORMER FOR A 12V HALOGEN LAMP by P. Fichera, R. Scollo 1. INTRODUCTION Lighting that uses halogen lamps is commonly found
Related documents
JTAG interface connection (20 pin)
www.mperl.comPin 3 (TRST) should be connected to target CPUs TRST pin (sometimes called NTRST). J-Link will also work if this pin is not connected, but you may experience some limitations when debugging. TRST should be separate from the CPU Reset (pin 15) Pin 11 (RTCK) should be connected to RTCK if available, otherwise to GND.
Aegis Padlock 3 - Apricorn
apricorn.comEach Aegis padlock 3.0 is shipped without a preset Personal Identification Number (PIN) installed on the key. A 6 to 16-digit Admin PIN must first be established before the drive can be used. This Admin PIN can be used to set any and all of the Admin Mode Features of the drive, as well as to access its data.
Motherboard Pin - Asus
dlcdnets.asus.comMotherboard Pin Definition 1-5 3. USB device wake-up (3-pin USBPWF) Set these jumpers to +5V to wake up the computer from S1 sleep mode (CPU stopped, DRAM refreshed, system running in low power mode) using the connected USB devices. Set to +5VSB to wake up from S3 and S4 sleep modes (no power to CPU, DRAM in slow
LT1963A - 1.5A, Low Noise, Fast Transient Response LDO ...
www.analog.comLT1963AET-3.3#PBF LT1963AET-3.3#TRPBF LT1963AET-3.3 5-Lead Plastic TO-220 –40°C to 125°C LT1963AEFE#PBF LT1963AEFE#TRPBF 1963AEFE 16-Lead Plastic TSSOP –40°C to 125°C LT1963AIFE#PBF LT1963AIFE#TRPBF 1963AIFE 16-Lead Plastic TSSOP –40°C to 125°C
AP2210 Description Pin Assignments
www.diodes.comGround pin current is the regulator quiescent current plus pass transistor base current. The total current drawn from the supply is the sum of the load . current plus the ground pin current. Symbol . Parameter : Conditions . Min : Typ . Max : Unit . e. no . Output Noise . I. OUT = 50mA, C.
PIN Security Requirement 18-3 Key Blocks
www.pcisecuritystandards.org3 Executive Summary Per PCI PIN Security Requirements, Requirement 18-3, “Key Blocks,” encrypted symmetric keys must be managed in structures called Key Blocks. The key usage must be cryptographically bound to the key using accepted methods, such that it must be infeasible for the key to be used if the usage attributes have been altered.
USB 3.1 USB TYPE-CTM
www.usb.orgJul 14, 2017 · USB 3.1 FRONT-PANEL INTERNAL CABLE AND CONNECTOR USB 3.1 FRONT-PANEL INTERNAL CONNECTOR AND CABLE, REVISION 1.1 6 2. MATING INTERFACES AND MECHANICAL REQUIREMENTS The receptacle connector mounted on motherboard (MB) is referred to as the header. To provide configuration flexibility of the USB ports on the front …