UM2448 User manual - STMicroelectronics
– 3 V to 3.6 V application voltage support on the UART interface and 5 V tolerant inputs (extended down to 1.65 V with the B-STLINK-VOLT or B-STLINK-ISOL board) – VCP frequency up to 16 MHz – Available on STDC14 debug connector (not available on MIPI10) • Multi-path bridge USB to SPI/UART/I2C/CAN/GPIOs specific features:
Download UM2448 User manual - STMicroelectronics
Information
Domain:
Source:
Link to this page:
Documents from same domain
Low-power dual operational amplifier - st.com
www.st.comFebruary 2016 DocID2471 Rev 17 1/24 This is information on a product in full production. www.st.com LM2904, LM2904A Low-power dual operational amplifier
AN3128 Application note - st.com
www.st.comJune 2011 Doc ID 16918 Rev 5 1/105 AN3128 Application note STM32 embedded graphic objects/touchscreen library Introduction This library is a firmware package which contains a collection of routines, data structures,
AN4767 Application note - st.com
www.st.comDocID028380 Rev 2 7/16 AN4767 Dual bank use cases 15 With dual bank, all the manipulation with the other bank is just another task of the main program.
AN3155 Application note - st.com
www.st.comOctober 2016 DocID17066 Rev 7 1/37 1 AN3155 Application note USART protocol used in the STM32 bootloader Introduction This application note describes the USART protocol used in the STM32 microcontroller
USB Power Delivery and Type-C - st.com
www.st.comUSB Type -C Overview USB Power Delivery specification introduces USB Type-C receptacle, plug and cable; they provide a smaller, thinner and more robust alternative to existing USB interconnect.
Datasheet - L78 - Positive voltage regulator ICs - …
www.st.comTO- 2 2 0 TO-2 2 0 F P DPAK D² PAK Features • Output current up to 1.5 A • Output voltages of 5; 6; 8; 8.5; 9; 12; 15; 18; 24 V • Thermal overload protection
AN2867 Application note - st.com
www.st.comMay 2017 DocID15287 Rev 11 1/43 1 AN2867 Application note Oscillator design guide for STM8AF/AL/S and STM32 microcontrollers Introduction Many designers know oscillators based on Pierce-Gate topology (hereinafter referred to as
AN4776 Application note - st.com
www.st.comMay 2017 DocID028459 Rev 2 1/73 1 AN4776 Application note General-purpose timer cookbook Introduction The timer peripheral is part of …
120-volt, 100-watt, DMOS audio amplifier with mute …
www.st.comSeptember 2010 Doc ID 6744 Rev 8 1/21 21 TDA7293 120-volt, 100-watt, DMOS audio amplifier with mute and standby Features Multipower BCD technology Very high operating voltage range (±50 V)
Electronic transformer for a 12V halogen lamp - …
www.st.comAPPLICATION NOTE AN528/0999 1/4 ELECTRONIC TRANSFORMER FOR A 12V HALOGEN LAMP by P. Fichera, R. Scollo 1. INTRODUCTION Lighting that uses halogen lamps is commonly found
Related documents
USB to I2C Example using the FT232H and FT201X devices
www.ftdichip.com2 FT232H USB-I2C Master This section shows how the FT232H can be programmed to act as a USB to I2C master interface. These routines can be used as the basis for communicating with other I2C slave devices. The routines will be used in the following chapter to communicate 2with the FT201X I C slave as an example.
CP2104 - Silicon Labs
www.silabs.comRS-232/RS-485 designs to USB using a minimum of components and PCB space. The CP2104 includes a USB 2.0 full-speed function controller, USB transceiver, oscillator, one-time programmable ROM, and asynchronous serial data bus (UART) with full modem control signals in a compact 4x4mm QFN-24 package (sometimes called “MLF” or “MLP”).
USB to serial chip CH340 - SparkFun Electronics
cdn.sparkfun.comCH340 is a USB bus convert chip and it can realize USB convert to serial interface, USB convert to IrDA infrared or USB convert to printer interface. In serial interface mode, CH340 supplies common MODEM liaison signal, used to enlarge asynchronous serial interface of computer or upgrade the common serial device to USB bus directly. More
NI Serial Hardware Specifications and Features Guide ...
www.ni.com4 | ni.com | NI Serial Hardware Specifications and Features Guide PXI-8433/2 RS-485/ RS-422 2 Yes 3000.0‡ DB-9 male 128 PXI-8433/4 RS-485/ RS-422 4 Yes 3000.0‡ 10P10C 128 * All NI serial hardware support s standard baud rates.In add ition, the PCI/NI PCIe/PXI-843 x family of
TTL-232R TTL to USB Serial Converter Range of Cables …
www.ftdichip.comThe TTL-232R cables are a family of USB to TTL serial UART converter cables incorporating FTDI’s FT232RQ USB to Serial UART interface IC device which handles all the USB signalling and protocols. The cables provide a fast, simple way to connect devices with a TTL level serial interface to USB.
Arduino : Introduction & Programming
students.iitk.ac.indisk controllers and serial/parallel port functions. These backplane-based microcomputers were used for data acquisition, process control and R&D projects, but were generally too bulky to be used as embedded systems within devices.
Raspberry Pi Compute Module 3+ Raspberry Pi Compute …
datasheets.raspberrypi.comUSB Interface USB Dx I/O - Z Leave open Serial interface USB OTGID I 3V3 Tie to GND OTG pin detect HDMI Interface HDMI SCL I/O 3V3b Zf Leave open DDC Clock (5.5V tolerant) HDMI SDA I/O 3V3b Zf Leave open DDC Data (5.5V tolerant) HDMI CEC I/O 3V3 Z Leave open CEC (has internal 27k pull up) HDMI CLKx O - Z Leave open HDMI serial clock
HC-05 Bluetooth Module - GM e
www.gme.czTXD UART_TXD, Bluetooth serial signal sending PIN Connect with the MCU’s (Microcontroller and etc) RXD PIN. RXD UART_RXD, Bluetooth serial signal receiving PIN Connect with the MCU’s (Microcontroller and etc) TXD PIN. KEY Mode switch input If it is input low level or connect to the air, the module is at paired or communication mode.