Example: confidence
28/40/44-Pin, Low-Power, High-Performance Microcontrollers ...
- Fixed Voltage Reference (FVR) with 1.024V, 2.048V and 4.096V output levels - 5-bit rail-to-rail resistive DAC with positive and negative reference selection • Charge Time Measurement Unit (CTMU) module: - Supports capacitive touch sensing for touch screens and capacitive switches eXtreme Low-Power Features (XLP) (PIC18(L)F2X/4XK22):
Tags:
Information
Domain:
Source:
Link to this page:
Documents from same domain
MCP1703 250 mA, 16V, Low Quiescent Current
ww1.microchip.com2010 Microchip Technology Inc. DS22049E-page 1 MCP1703 Features: • 2.0 µA Typical Quiescent Current • Input Operating Voltage Range: 2.7V to16.0V
Low Quiescent Current LDO - Microchip Technology
ww1.microchip.com2005-2016 Microchip Technology Inc. DS20001826D-page 1 MCP1700 Features: • 1.6 µA Typical Quiescent Current • Input Operating Voltage Range: 2.3V to 6.0V
Power Factor Correction in Power Conversion …
ww1.microchip.com© 2007 Microchip Technology Inc. DS01106A-page 2 AN1106 FIGURE 1: CURRENT WAVEFORMS WITH AND WITHOUT PFC These waveforms illustrate that …
Data Encryption Routines for PIC24 and dsPIC Device
ww1.microchip.com© 2006 Microchip Technology Inc. DS01044A-page 1 AN1044 INTRODUCTION Currently, there are three data encryption standards approved …
2.7V to 5.5V Single Supply CMOS Op Amp
ww1.microchip.comMCP601/1R/2/3/4 DS21314G-page 2 © 2007 Microchip Technology Inc. 1.0 ELECTRICAL CHARACTERISTICS Absolute Maximum Ratings † VDD –VSS.....7.0V
Using SAM-BA for Linux on SAMA5D3 Xplained
ww1.microchip.comAN-8995 – Using SAM-BA for Linux on SAMA5D3 Xplained: 42328A−06/2014 Page 5 of 19 2. Setup With Ubuntu distributions, a user has to be member of the dialout group to access serial devices like
MCP6021/1R/2/3/4 - Rail-to-Rail Input/Output, 10 …
ww1.microchip.com2001-2017 Microchip Technology Inc. DS20001685E-page 1 MCP6021/1R/2/3/4 Features • Rail-to-Rail Input/Output • Wide Bandwidth: 10 MHz (typical)
MTCH6102 Low-Power Projected Capacitive Touch …
ww1.microchip.com2014 Microchip Technology Inc. DS40001750A-page 1 Description: Microchip’s MTCH6102 is a turnkey projected capacitive touch controller that simplifies adding
PIC32 GUI Development Board with Projected …
ww1.microchip.comPIC32 GUI Development Board with Projected Capacitance (PCAP) Touch Information Sheet Microchip Technology Inc.
RN4020 Bluetooth Low Energy Module User’s Guide
ww1.microchip.comRN4020 BLUETOOTH LOW ENERGY MODULE USER’S GUIDE 2014 Microchip Technology Inc. DS70005191B-page 7 Preface INTRODUCTION This chapter contains general information that will be useful to know before using the
Related documents
Lecture 17: Clock Recovery - Stanford University
web.stanford.edu(transmitter clock is sent along with the data) • The basic circuit block is a Phase Locked Loop ... • Main goal is to achieve low offset • Loop filters ... whose value is adjusted by the control voltage/current: • Main problem: Create a “resistor” that is both variable AND linear ctrl load o+ o …
NELES® ND9000 INTELLIGENT VALVE CONTROLLER
www.valin.comSupply power: Loop powered, 4–20 mA Minimum signal: 3.6 mA Current max : 120 mA Load voltage: up to 9.7 VDC/20 mA (corresponding 485 Ω) Voltage: max. 30 VDC Polarity protection: -30 VDC Over current protection: active over 35 mA Profibus PA and FOUNDATION fieldbus Supply power: voltage 9–32 VDC, reverse polarity protection
Dual/Quad Rail-to-Rail Operational Amplifiers OP295/OP495
www.analog.comLow offset voltage: 300 μV . Gain bandwidth product: 75 kHz . High open-loop gain: 1000 V/mV . Unity-gain stable . Low supply current/per amplifier: 150 μA maximum . APPLICATIONS . Battery-operated instrumentation . Servo amplifiers . Actuator drives . Sensor conditioners . Power supply control . GENERAL DESCRIPTION
Kinetis K66 Sub-Family - NXP
www.nxp.comSymbol Description Min. Max. Unit VDD Digital supply voltage –0.3 3.8 V IDD Digital supply current — 300 mA VDIO Digital1 input voltage,including RESET_b –0.3 VDD + 0.3 V VAIO Analog1 input voltage, including EXTAL32 and XTAL32 –0.3 VDD + 0.3 V ID Maximum current single pin limit (digital output pins) –25 25 mA VDDA Analog supply voltage VDD – 0.3 VDD + …
MCP2561/2FD High-Speed CAN Flexible Data Rate Transceiver
ww1.microchip.comapplying high-level voltage to the STBY pin. In Standby mode, the transmitter and the high-speed part of the receiver are switched off to minimize power consumption. The low-power receiver and the wake-up filter blocks are enabled to monitor the bus for activity. The receive pin (R
Rosemount 3051 Pressure Transmitter - Emerson Electric
www.emerson.com3.1.5 In-line gage transmitter orientation. The low side pressure port (atmospheric reference) on the in-line gage transmitter is located in the neck of the transmitter, behind the housing. The vent path is 360° around the transmitter between the housing and sensor. (See Figure 3-6) Keep the vent path free of any obstruction, including but not ...
Low Voltage Temperature Sensors Data Sheet …
www.analog.comLow Voltage Temperature Sensors Data Sheet TMP35/TMP36/TMP37 FEATURES Low voltage operation (2.7 V to 5.5 V) S Calibrated directly in °C . 10 mV/°C scale factor (20 mV/°C on . TMP37) ±2°C accuracy over tempe rature (typ) ±0.5°C linearity (typ) Stable with large capacitive loads . Specified −40°C to +125°C, operation to +150°C
MC68HC908GP32, MC68HC908GP32 - Data Sheet - NXP
www.nxp.comMC68HC908GP32 Data Sheet, Rev. 10 Freescale Semiconductor 5 January, 2008 10 Figure 13-5. SCI Receiver Block Diagram — Replaced SCI receiver block diagram