Example: marketing
Aluminum Lugs - ABB Electrification
Material: E.C. grade aluminum. Connector bores are coated with HM 53 (an oxide-inhibiting compound) and capped. Mounting holes sized for 1⁄ 2" bolts (9⁄ 16" hole size). Optional suffix “-38” for 3⁄ 8" bolts (13⁄ 32" hole size). • Use with aluminum and copper conductors • Provides high strength and high conductivity
Tags:
Information
Domain:
Source:
Link to this page:
Documents from same domain
T&B CABLE TRAY METALLIC CABLE TRAY
tnb.ca.abb.comA34 T&B CABLE TRAY METALLIC CABLE TRAY — Aluminum cable tray Straight lengths — Tray bottom types: ladder, ventilated and solid trough Ladder Extra wide aluminum rungs are welded to extruded aluminum I-beam side rails. Every second rung is reversed to allow for easy top or bottom mounting of cable ties and clamps. All edges and welds are
Flexible cord and cable fittings
tnb.ca.abb.comcord and fixture wire 2. UL 514A and 514B – Safety standard for outlet boxes and fittings 3. CEC Section 4 – Conductors 4-012 – Uses of flexible cord 4-040 – Uses of portable power cable 12-010 (4) – Flexible cords in ducts and plenum chambers 22-108 (2) – Bonding conductor for flexible cords for portable equipment
A Star Teck® - Teck and tray cable fittings
tnb.ca.abb.comStar Teck - Teck and tray cable fittings. The Star Teck family A4 Specifications A6 Hazardous locations – CEC classifications A8 Hazardous locations – class, zone A12 and division certifications Quick reference A13 Star Teck (ST®) – series …
Electrical metallic tubing (EMT) fittings - ABB
tnb.ca.abb.comapproximately 40 percent as much as rigid steel conduit of the same nominal size. EMT can be used, reference CEC Rule 12-1402, for both exposed or concealed work provided that, during installation or afterwards, it is not subjected to severe physical damage. Galvanized steel EMT installed in concrete, on grade or above, generally requires no
Hazardous Locations CEC Classifications - tnb.ca.abb.com
tnb.ca.abb.comGas group designations Two systems of groupings for gases are included in the 1998 CEC: the pre-1998 division gas groups consisting of Groups A, B, C and D; and the IEC system consisting of Groups IIA, IIB and IIC. Both systems are accepted by the CEC. Division gas groups Gorup A acetylene Group B butadiene, hydrogen, manufactured gases
H T&B Liquidtight Systems™ Liquidtight flexible metal ...
tnb.ca.abb.comT&B Liquidtight fittings, engineered to perform in the toughest environments T&B Liquidtight metallic flexible conduit fittings 1. Gland deflects water away from connector and prevents "pooling" of moisture. Look for the distinctive pumpkin appearance of the gland nut. 2. Self-Cleaning Threads inside gland nut keep dirt
Related documents
Chapter 2. Production and Processing of Aluminum
www.tms.orgplay no significant role in today’s aluminum production. Chapter 16 will show that the world’s bauxite supplies are guaranteed into the distant future. 2.1.2 The alumina plant The starting material for electrolytic smelting of aluminum is pure, anhydrous alumi-num oxide (Al 2 O 3) called alumina. In the Western World, the Bayer 1 process ...
TECHNICAL DATA SHEET - Johns Manville
www.jm.comComposition Differences in Aluminum Alloys (%) Alloy Cu Mn Mg Zn 3105 ≤ 0.3 0.3-0.8 0.2-0.8 ≤ 0.4 3003 0.05-0.2 1-1.5 --- ≤ 0.1 COMPLIANCE TO STANDARDS All bare and polyfilm lined JM Aluminum Jacketing complies with the requirements of ASTM C1729 (Aluminum Jacketing Material Standard) which includes the strength and chemical composition
Chapter 13. Material Handling Systems - gatech.edu
www2.isye.gatech.eduChapter 13. Material Handling Systems This is an introduction chapter quotation. It is offset three inches to the right. 13.1. Material Handling Introduction Material Handling Definition Several definitions of Material(s) Handling exist. Materials Handling is defined in Compton’s
APPENDIX B: MATERIAL SETTINGS - Epilog Laser
www.epiloglaser.com- 191 - APPENDIX B: MATERIAL SETTINGS Fusion Series Suggested Material Settings (CO2) • These are only suggestions: Every type of material will react differently with the laser, even from one plastic to the next. Use these settings as your starting point then adjust one variable at a time until you achieve the result you desire.
Form and Stability of Aluminum Hydroxide Complexes in ...
pubs.usgs.govAluminum has a particularly strong tendency to hydrolize in solution, and at any pH above 3.5 various combinations of aluminum with hydroxide ions occur. The purpose of this investigation was to determine the effect of pH on aluminum solubility and …
Experiment 4: Synthesis of Alum from Scrap Aluminum
www.bc.eduAluminum Objective: In this experiment, you will be converting the aluminum metal from a beverage can into the chemical compound potassium aluminum sulfate, KAl(SO 4) 2•12 H 2 O, commonly referred to as alum. Introduction It had been a good year for the O’Keefe farm with just the right amount of sun and rain.