Example: tourism industry
Design, Accuracy, and Calibration of Analog to Digital ...
Design, Accuracy, and Calibration of Analog to Digital Converters on the MPC5500 Family, Rev. 2 Freescale Semiconductor 3 uses a buffer to charge th is up initially. This ADC architecture runs at moderate speeds and is economical to implement, but relies on the DAC and a good amplifier offset for accuracy. Figure 1.
Tags:
Information
Domain:
Source:
Link to this page:
Documents from same domain
DSP56156 16-Bit Digital Signal Processor - nxp.com
www.nxp.comThe DSP56156 is a general-purpose MPU-style Digital Signal Processor (DSP). On a single semi- conductor chip, the DSP56156 comprises a very efficient 16-bit digital signal processing core, pro-
SAA7706H Car radio Digital Signal Processor (DSP)
www.nxp.comCar radio Digital Signal Processor (DSP) SAA7706H This text is here in white to force landscape pages to be rotated correctly when browsing through the pdf in the Acrobat reader.This text is here in _white to force landscape pages to be rotated correctly when browsing through the pdf in the Acrobat reader.This text is here inThis text is here in
AN10441 Level shifting techniques in I2C-bus design
www.nxp.comDocument information AN10441 Level shifting techniques in I2C-bus design Rev. 01 — 18 June 2007 Application note Info Content Keywords I2C-bus, level shifting Abstract Logic level shifting may be required when interfacing legacy devices with
AN3234: Washing Machine Three-Phase AC …
www.nxp.comWashing Machine Three-Phase AC Induction Motor Drive, Rev. 0 Indirect Vector Control 4 Freescale Semiconductor If you are looking for more theory on the field ...
1. General description - nxp.com
www.nxp.com1. General description The TJA1044 is part of the Mantis family of high-speed CAN transceivers. It provides an interface between a Controller Area Network (CAN) protocol controller and the physical
PCA9570 Remote 4-bit general purpose outputs for 1 MHz …
www.nxp.com1. General description The PCA9570 is a CMOS device that provides 4 bits of General Purpose parallel Output (GPO) expansion in low voltage processor and handheld battery powered mobile
P82B96 Dual bidirectional bus buffer - nxp.com
www.nxp.com1. General description The P82B96 is a bipolar IC that creates a non-latching, bidirectional, logic interface between the normal I2C-bus and a range of other bus configurations.It can interface
S32K144 EVB Quick Start Guide - NXP Semiconductors
www.nxp.comJ14 SWD connector. 3 EXTERNAL USE S32K144 EVBFeatures: ... USB connector of the USB cable to micro-B port J7 on the S32K144EVB. ... Windows, Linux and Mac operating systems. Using the MSD Flash Programmer 1. Locate the .srec file of your project , file is under the
Three-Phase BLDC Motor Sensorless Control Using …
www.nxp.comThis document describes the design of a three-phase brushless DC motor (BLDC motor) drive based on Freescale’s MC56F8013 and MC56F8023 dedicated motor control device. Brushless DC motors are popular in a wide application area.
AN11443 BFU550XR ISM 433 MHz LNA design - nxp.com
www.nxp.comAN11443 BFU550XR ISM 433 MHz LNA design Rev. 1 — 23 January 2014 Application note . Document information Info Content Keywords BFU520, BFU530, BFU550 series, ISM-band, 433MHz 866MHz Abstract This document describes an ISM Frequency LNA design on BFU5xxXR Starter kit
Related documents
SECTION 6.1: DIGITAL-TO-ANALOG CONVERTER …
www.analog.comCHAPTER 6: CONVERTERS Introduction There are two basic type of converters, digital-to-analog (DACs or D/As) and analog-to-digital (ADCs or A/Ds). Their purpose is fairly straightforward. In the case of DACs, they output an analog voltage that is a proportion of a reference voltage, the proportion based on the digital word applied.
Analog to Digital Conversion - mccdaq.com
www.mccdaq.comAnalog-to-Digital Converters (ADCs) transform an analog voltage to a binary number (a series of 1’s and 0’s), and then eventually to a digital number (base 10) for reading on a meter, monitor, or chart. The number of binary digits (bits) that represents the digital number determines the ADC resolution. However, the digital
ECE 431 Digital Signal Processing Lecture Notes
cobb.ece.wisc.eduDigital Signal Processing (DSP) is the application of a digital computer to modify an analog or digital signal. Typically, the signal beingprocessedis eithertemporal, spatial, orboth. For example, an audio signal is temporal, while an image is spatial. A movie is both temporal and spatial. The
Digital-to-Analog Converter ICs
www.analog.comDAC . In order to achieve their rated performance specifications, high speed data converters require a fast rising, low jitter sampling clock . In large complex systems where there are many digital chips requiring clock signals as a reference, it can be a
DIGITAL CAMERA
download.nikonimglib.comDIGITAL CAMERA User's Manual En Nikon Manual Viewer 2 Use the Nikon Manual Viewer 2 app to view manuals anytime, anywhere on your smartphone or tablet. ... • Do not use with travel converters or adapters designed to convert from one voltage to another or with DC-to-AC inverters. Failure to observe
DC to AC Converters Inverters - Engineering
www.site.uottawa.caELG4139: DC to AC Converters Converts DC to AC power by switching the DC input voltage (or current) in a pre-determined sequence so as to generate AC voltage (or current) output. I …
Introduction to Digital Electronics - Agner
www.agner.orgA digital system typically has a fixed number of bits to represent a binary number. For example, if we have four bits, we can have the numbers from 0 to 15: binary decimal 0000 0 0001 1 0010 2 0011 3 0100 4 0101 5 0110 6 0111 7 1000 8 1001 9 1010 10 …