Example: barber
HV9910B Data Sheet - Microchip Technology
Jan 27, 2015 · • DC/DC or AC/DC LED driver applications • RGB backlighting LED driver • Back lighting of flat panel displays • General purpose constant current source • Signage and decorative LED lighting • Chargers Description HV9910B is an open loop, current mode control, LED driver IC. This IC can be programmed to operate in either a constant ...
Tags:
Information
Domain:
Source:
Link to this page:
Documents from same domain
MCP1703 250 mA, 16V, Low Quiescent Current
ww1.microchip.com2010 Microchip Technology Inc. DS22049E-page 1 MCP1703 Features: • 2.0 µA Typical Quiescent Current • Input Operating Voltage Range: 2.7V to16.0V
Low Quiescent Current LDO - Microchip Technology
ww1.microchip.com2005-2016 Microchip Technology Inc. DS20001826D-page 1 MCP1700 Features: • 1.6 µA Typical Quiescent Current • Input Operating Voltage Range: 2.3V to 6.0V
Power Factor Correction in Power Conversion …
ww1.microchip.com© 2007 Microchip Technology Inc. DS01106A-page 2 AN1106 FIGURE 1: CURRENT WAVEFORMS WITH AND WITHOUT PFC These waveforms illustrate that …
Data Encryption Routines for PIC24 and dsPIC Device
ww1.microchip.com© 2006 Microchip Technology Inc. DS01044A-page 1 AN1044 INTRODUCTION Currently, there are three data encryption standards approved …
2.7V to 5.5V Single Supply CMOS Op Amp
ww1.microchip.comMCP601/1R/2/3/4 DS21314G-page 2 © 2007 Microchip Technology Inc. 1.0 ELECTRICAL CHARACTERISTICS Absolute Maximum Ratings † VDD –VSS.....7.0V
Using SAM-BA for Linux on SAMA5D3 Xplained
ww1.microchip.comAN-8995 – Using SAM-BA for Linux on SAMA5D3 Xplained: 42328A−06/2014 Page 5 of 19 2. Setup With Ubuntu distributions, a user has to be member of the dialout group to access serial devices like
MCP6021/1R/2/3/4 - Rail-to-Rail Input/Output, 10 …
ww1.microchip.com2001-2017 Microchip Technology Inc. DS20001685E-page 1 MCP6021/1R/2/3/4 Features • Rail-to-Rail Input/Output • Wide Bandwidth: 10 MHz (typical)
MTCH6102 Low-Power Projected Capacitive Touch …
ww1.microchip.com2014 Microchip Technology Inc. DS40001750A-page 1 Description: Microchip’s MTCH6102 is a turnkey projected capacitive touch controller that simplifies adding
PIC32 GUI Development Board with Projected …
ww1.microchip.comPIC32 GUI Development Board with Projected Capacitance (PCAP) Touch Information Sheet Microchip Technology Inc.
RN4020 Bluetooth Low Energy Module User’s Guide
ww1.microchip.comRN4020 BLUETOOTH LOW ENERGY MODULE USER’S GUIDE 2014 Microchip Technology Inc. DS70005191B-page 7 Preface INTRODUCTION This chapter contains general information that will be useful to know before using the
Related documents
320W Constant Voltage + Constant Current LED Driver …
www.meanwell.com320w constant voltage + constant current led driver hlg-320h series specification model dc voltage rated current rated power output voltage adj. range current adj. range line regulation load regulation ± setup, rise time note.6 hold up time (typ.) voltage range note.5 frequency range power factor (typ.)
Understanding LED Drivers - 1000Bulbs.com
www.1000bulbs.comConstant-Voltage Drivers Constant-voltage drivers power LEDs that require a fixed output voltage with a maximum output current. In these LEDs, the current is already regulated, either by simple resistors or an internal constant-current driver, within the LED module. These LEDs require one stable voltage, usually 12V DC or 24V DC.
Hi-lume 1% 2-Wire LED Driver Forward-Phase Control Overview
www.lutron.comThe Hi-lume 1% 2-Wire LED Driver is a high-performance LED driver that provides smooth, continuous, flicker-free, 1% dimming for virtually any LED fixture, whether it requires constant-current or constant-voltage. Formerly part of the A-series family, it is the most versatile LED driver offered today due to
Hi-lume 1% EcoSystem / 3-Wire L3D Driver Overview
www.lutron.comhigh-performance LED driver that provides smooth, continuous 1% dimming for virtually any LED fixture, whether it requires constant-current or constant-voltage. It is the most versatile LED driver offered today due to its compatibility with a wide variety of LED arrays, multiple form factors, and numerous control options. Features
LCGR SERIES-L E D
www.usaltg.comLED’s are available in standard Neutral White (4000K), or optional Cool White (5000K) or Warm White (3000K). Consult Factory for other LED options. LED DRIVER UL and CUL recognized Constant Current LED drivers operate on input voltages from 120-277VAC, 50/60hz. Consult Factory for (347-480VAC). Driver is mechanically fastened to
www.i-enet - Adafruit Industries
cdn-shop.adafruit.comThe WS2811 is 3 output channels special for LED driver circuit. It internal include intelligent digital port data latch and signal reshaping amplification drive circuit.Also include a precision internal oscillator and a 12V voltage programmable constant current output drive. In the purpose of reduce power supply ripple, the 3 outp-
LED Dimming: What you need to know - Energy
www1.eere.energy.govDec 10, 2012 · (average) current is constant (Constant Current) • Typically, power electronics components are used to create circuits which convert AC voltage into regulated LED constant (average) current ssl.energy.gov 10 eere.energy.gov
PROJECT TYPE: RAZAR SERIES-LED
www.usaltg.comLED DRIVER(S) Constant current electronic with a power factor of >.90 and a minimum operating temperature of -40°F /-40°C. Driver(s) is/are UL and cUL recognized and mounted directly against the Electrical Housing to facilitate thermal transfer, held down by universal clamps to facilitate easy removal. In-line terminal blocks facilitate
LED Basics - Purdue University College of Engineering
engineering.purdue.eduobserver due to higher average forward current being supplied to the LED. For maximum brightness, a constant current (i.e., the duty ratio of the current pulse is one) will be supplied to the LED. The advantage of this method over the AM diming is the absence of spectral slide and uniform dimming over different LED strings.
Electronic Control Transmission (ECT)
autoshop101.comfour terminals: VC, VTA, IDL and E. A constant 5 volts is applied to terminal VC from the engine ECU. As the contact point slides along the resistor with throttle opening, voltage is applied to the VTA terminal. This voltage increases linearly from 0 volts at closed throttle to 5 volts at wide-open throttle.