Example: tourism industry
NI 9472 Datasheet - National Instruments
variety of industrial devices such as motors, actuators, and relays. There are three connector options for the NI 9472—a 10-position screw-terminal connector, a 10-position spring-terminal connector, and a 25-position DSUB connector. This industry-standard 25-position DSUB connector provides for low-cost cabling to a wide variety of
Tags:
Information
Domain:
Source:
Link to this page:
Documents from same domain
Using Acoustic Beamforming for Pass-By Noise …
www.ni.comUsing Acoustic Beamforming . for Pass-By Noise Source Detection . NATIONAL INSTRUMENTS. APPLICATION NOTES. Abstract. This application note discusses a technique known as beamforming for determining noise location of passing
GETTING STARTED GUIDE to ±10 V, 16 Bit, 250 …
www.ni.comMeasurement Category I is for measurements performed on circuits not directly connected to the electrical distribution system referred to as MAINS voltage.
NI 6509 User Guide and Specifications - National …
www.ni.comUSER GUIDE AND SPECIFICATIONS NI 6509 This document contains information about using the NI PCI-6509, NI PXI-6509, and NI PCIe-6509 data acquisition devices with the
NI 6528/6529 User Guide and Specifications - …
www.ni.comNI 6528/6529 User Guide and Specifications 6 ni.com Operate the DIO device only at or below Pollution Degree 2. Pollution is foreign matter in a solid, liquid, or gaseous state that can reduce dielectric
PXIe-5820 Getting Started Guide - National …
www.ni.comElectromagnetic Compatibility Guidelines This product was tested and complies with the regulatory requirements and limits for electromagnetic compatibility (EMC) stated in the product specifications.
DEVICE SPECIFICATIONS NI 6722/6723
www.ni.comDEVICE SPECIFICATIONS NI 6722/6723 This document lists the specifications for the NI 6722/6723 analog output devices. The following specifications are typical at 25°C unless otherwise noted.
NI cRIO-9030 Specifications - National Instruments
www.ni.comSPECIFICATIONS NI cRIO-9030 Embedded CompactRIO Controller with Real-Time Processor and Reconfigurable FPGA This document lists the specifications for the National Instruments cRIO-9030.
NI PS-15 Power Supply User Manual and …
www.ni.com©National Instruments Corporation viii NI PS-15 Power Supply User Manual About This Manual The NI PS-15 Power Supply User Manual describes the features and specifications of the NI PS-15 power supply and contains information
NI cDAQ -9191
www.ni.comDigital output sample clock frequency Streaming from application memory System-dependent Regeneration from FIFO 0 MHz to 10 MHz Finite 0 MHz to 10 MHz
NI PXIe-1435 User Guide and Specifications - …
www.ni.comNI PXIe-1435 User Guide and Specifications The NI PXIe-1435 (NI 1435) is a PXI Express (PXIe) image acquisition device that supports Base, Medium, Full, and Extended Full configuration Camera Link cameras and supports Power over Camera
Related documents
G01 through G10 Spring-Return Pneumatic Actuators with …
www.emerson.comG7XXX SR, G8XXX SR, and G10XXX SR Spring-Return Series Single Pneumatic Power Module Actuators with M11 or M11 S Hydraulic Override Module. 1.1.2 Normal recommended service interval for this actuator series is five years. NOTE: Storage time …
Double Acting (air to air) and Single Acting KEYSTONE ...
www.emerson.comSpring Return models : up to 1414 Nm Temperature range : -30° to +90°C* with standard components. * An extended temperature range from -30°C to +150°C is available on request. Double Acting (air to air) and Single Acting (spring return), 90° operation, pneumatic actuators General Applications For remote control of any quarter turn
Chapter 5 - Schemes of directional control valves - ISO ...
www.hafner-pneumatik.comIn the scheme below two 2/2-way solenoid valves (S1 and S2) are used to control a cylinder with spring return (single acting) C1. Without actuation both solenoid valves are closed. In order to move the piston rod to the outer position (right) S2 has to be actuated . Compressed air is flowing from the so urce through S2 into the cylinder. In
AT-FM-10K Two-Hand Control Module - Banner Engineering
info.bannerengineering.comthe hazard. The two-hand control actuators must be located in a way that hazardous motion is completed or stopped before the operator can release one or both of the buttons and reach the hazard (see Separation Distance). AT-FM-10K Two-Hand Control Module 2 www.bannerengineering.com - Tel: + 1 888 373 6767 P/N 64137 Rev. I