MCP6001/1R/1U/2/4 - 1 MHz, Low-Power Op Amp
May 14, 2019 · op amps is designed with Microchip’s advanced CMOS process. The MCP6001/2/4 family is available in the industrial and extended temperature ranges, with a power supply range of 1.8V to 6.0V. Package Types R1 VOUT R2 VIN VDD + – Gain 1 R1 R2 = + ----- - Noninverting Amplifier MCP6001 VREF VSS 4 5 4 5 4 MCP6001 1 2 3 5 VDD VIN-OUT VSS …
Download MCP6001/1R/1U/2/4 - 1 MHz, Low-Power Op Amp
Information
Domain:
Source:
Link to this page:
Please notify us if you found a problem with this document:
Documents from same domain
Power Factor Correction in Power Conversion …
ww1.microchip.com© 2007 Microchip Technology Inc. DS01106A-page 2 AN1106 FIGURE 1: CURRENT WAVEFORMS WITH AND WITHOUT PFC These waveforms illustrate that …
Power, Factors, Correction, Power factor correction in power conversion, Conversion
2.7V to 5.5V Single Supply CMOS Op Amp
ww1.microchip.comMCP601/1R/2/3/4 DS21314G-page 2 © 2007 Microchip Technology Inc. 1.0 ELECTRICAL CHARACTERISTICS Absolute Maximum Ratings † VDD –VSS.....7.0V
Data Encryption Routines for PIC24 and dsPIC Device
ww1.microchip.com© 2006 Microchip Technology Inc. DS01044A-page 1 AN1044 INTRODUCTION Currently, there are three data encryption standards approved …
Data, Routines, Data encryption, Encryption, Data encryption routines for pic24 and, Pic24
Using SAM-BA for Linux on SAMA5D3 Xplained
ww1.microchip.comAN-8995 – Using SAM-BA for Linux on SAMA5D3 Xplained: 42328A−06/2014 Page 5 of 19 2. Setup With Ubuntu distributions, a user has to be member of the dialout group to access serial devices like
MCP6021/1R/2/3/4 - Rail-to-Rail Input/Output, 10 …
ww1.microchip.com2001-2017 Microchip Technology Inc. DS20001685E-page 1 MCP6021/1R/2/3/4 Features • Rail-to-Rail Input/Output • Wide Bandwidth: 10 MHz (typical)
Low Quiescent Current LDO - Microchip Technology
ww1.microchip.com2005-2016 Microchip Technology Inc. DS20001826D-page 1 MCP1700 Features: • 1.6 µA Typical Quiescent Current • Input Operating Voltage Range: 2.3V to 6.0V
MCP1703 250 mA, 16V, Low Quiescent Current
ww1.microchip.com2010 Microchip Technology Inc. DS22049E-page 1 MCP1703 Features: • 2.0 µA Typical Quiescent Current • Input Operating Voltage Range: 2.7V to16.0V
MTCH6102 Low-Power Projected Capacitive Touch …
ww1.microchip.com2014 Microchip Technology Inc. DS40001750A-page 1 Description: Microchip’s MTCH6102 is a turnkey projected capacitive touch controller that simplifies adding
Controller, Touch, Capacitive, Projected capacitive touch, Projected, Projected capacitive touch controller
PIC32 GUI Development Board with Projected …
ww1.microchip.comPIC32 GUI Development Board with Projected Capacitance (PCAP) Touch Information Sheet Microchip Technology Inc.
Development, With, Board, Projected, Gui development board with projected, Gui development board with projected capacitance, Capacitance
RN4020 Bluetooth Low Energy Module User’s Guide
ww1.microchip.comRN4020 BLUETOOTH LOW ENERGY MODULE USER’S GUIDE 2014 Microchip Technology Inc. DS70005191B-page 7 Preface INTRODUCTION This chapter contains general information that will be useful to know before using the
Guide, User, Energy, Module, Rn4020 bluetooth low energy module user s guide, Rn4020, Bluetooth
Related documents
LM 358 Op Amp - electronics123
www.electronics123.netSome of many Op-Amp applications: Voltage uffers Wave form generators (square, sine, triangle) Differentiators and Integrators Low Pass and High pass Filters omparators Figure 1: LM358 Duel Op-Amp DIP 8 The LM358 is a duel op-amp, meaning there’s two op amps in one I. We will only work with one for now.
IdealOpAmpCircuits
leachlegacy.ece.gatech.eduspecified to draw no morethan0.1mA fromthe output of theop amp whentheopen-circuit output voltage isintherange−10V≤vO≤10V. Solution. The circuit diagram for the amplifier is shown in Fig. 1.8. To meet the input resistance specification,wehaveRi 10/(RF+R1). Iftheequalityisused,weobtainRF+R1=100kΩ. Forthespecifiedopen-circuitvoltage ...
CIRCUITS LABORATORY EXPERIMENT 9 Operational Amplifiers
classes.engineering.wustl.edulinear op amp circuits is to use of negative feedback to always force (V+ - V-) to be suf - ficiently small so that the amplifier is operating in that very narrow linear region. Figure 9.3: Ideal op amp input-output characteristic. There is a simple algorithm for …
Op Amps for Everyone Design Guide (Rev. B)
web.mit.eduthe op amp’s place in the world of analog electronics. Chapter 2 reviews some basic phys-ics and develops the fundamental circuit equations that are used throughout the book. Similar equations have been developed in other books, but the presentation here empha-sizes material required for speedy op amp design. The ideal op amp equations are devel-
High Performance Video Op Amp - Analog Devices
www.analog.comHigh Performance Video Op Amp Data Sheet AD811 FEATURES High speed 140 MHz bandwidth (3 dB, G = +1) 120 MHz bandwidth (3 dB, G = +2) +IN. 35 MHz bandwidth (0.1 dB, G = +2) 2500 V/µs slew rate . 25 ns settling time to 0.1% (for a 2 V step) 65 ns settling time to 0.01% (for a 10 V step) Excellent video performance (R L 1=150 Ω)