Motor control Reference Guide - STMicroelectronics
29 Motor Driver ICs 39 Power Modules 44 Power MOSFETs 48 IGBT 49 600-650 V IGBT series 50 1200 V IGBT series 51 Diode & Rectifier 52 Thyristors, Triacs and AC Switches 54 Protection & Filters devices 56 MOSFET and IGBT Gate Drivers 60 Silicon Carbide and Gallium Nitride Gate Drivers 62 Current, Speed & Positioning Sensing. ST’s commitment to
Download Motor control Reference Guide - STMicroelectronics
Information
Domain:
Source:
Link to this page:
Documents from same domain
Low-power dual operational amplifier - st.com
www.st.comFebruary 2016 DocID2471 Rev 17 1/24 This is information on a product in full production. www.st.com LM2904, LM2904A Low-power dual operational amplifier
AN3128 Application note - st.com
www.st.comJune 2011 Doc ID 16918 Rev 5 1/105 AN3128 Application note STM32 embedded graphic objects/touchscreen library Introduction This library is a firmware package which contains a collection of routines, data structures,
AN4767 Application note - st.com
www.st.comDocID028380 Rev 2 7/16 AN4767 Dual bank use cases 15 With dual bank, all the manipulation with the other bank is just another task of the main program.
AN3155 Application note - st.com
www.st.comOctober 2016 DocID17066 Rev 7 1/37 1 AN3155 Application note USART protocol used in the STM32 bootloader Introduction This application note describes the USART protocol used in the STM32 microcontroller
USB Power Delivery and Type-C - st.com
www.st.comUSB Type -C Overview USB Power Delivery specification introduces USB Type-C receptacle, plug and cable; they provide a smaller, thinner and more robust alternative to existing USB interconnect.
Datasheet - L78 - Positive voltage regulator ICs - …
www.st.comTO- 2 2 0 TO-2 2 0 F P DPAK D² PAK Features • Output current up to 1.5 A • Output voltages of 5; 6; 8; 8.5; 9; 12; 15; 18; 24 V • Thermal overload protection
AN2867 Application note - st.com
www.st.comMay 2017 DocID15287 Rev 11 1/43 1 AN2867 Application note Oscillator design guide for STM8AF/AL/S and STM32 microcontrollers Introduction Many designers know oscillators based on Pierce-Gate topology (hereinafter referred to as
AN4776 Application note - st.com
www.st.comMay 2017 DocID028459 Rev 2 1/73 1 AN4776 Application note General-purpose timer cookbook Introduction The timer peripheral is part of …
120-volt, 100-watt, DMOS audio amplifier with mute …
www.st.comSeptember 2010 Doc ID 6744 Rev 8 1/21 21 TDA7293 120-volt, 100-watt, DMOS audio amplifier with mute and standby Features Multipower BCD technology Very high operating voltage range (±50 V)
Electronic transformer for a 12V halogen lamp - …
www.st.comAPPLICATION NOTE AN528/0999 1/4 ELECTRONIC TRANSFORMER FOR A 12V HALOGEN LAMP by P. Fichera, R. Scollo 1. INTRODUCTION Lighting that uses halogen lamps is commonly found
Related documents
High Voltage, Isolated Gate Driver with Internal Miller ...
www.analog.comHigh Voltage, Isolated Gate Driver with Internal Miller Clamp, 2 A Output Data Sheet ADuM4121/ADuM4121-1 ... reliable control over the switching characteristics of insulated gate bipolar transistor (IGBT)/metal oxide semiconductor field, effect transistor (MOSFET) configurations over a wide range of
MOSFET/IGBT DRIVERS THEORY AND APPLICATIONS
www.ixys.comThe Driver is supplied by Vcc of value Vp and its ground is connected to the common ground of V DD and is returned to the Source of the MOSFET. The output from the Driver is connected to the Gate of the MOSFET through a resistor R Gext. Now when a positive going pulse appears at the input ter-minal of the Driver, an amplified pulse appears at ...
Dedicated enable pin RMS • DFN-14 (pin to pin compatible ...
www.skyworksinc.comDriver outputs can be grounded to the same or separate grounds or connected to a pos- ... ness make the Si827x family ideal for a wide range of isolated MOSFET/IGBT and SiC or GaN FET gate drive applications. Automotive Grade products are built using automotive-specific flows at …
Bootstrap Circuitry Selection for Half Bridge Configurations
www.ti.comto the gate driver supply pins. Figure 8 below shows a good layout example using UCC27710 with all bootstrap components located near the gate driver IC minimizing any effects of parasitic inductances and reducing the high peak currents path of the bootstrap circuit. It is also important to separate high voltage power and low voltage signal traces.
2.5 A Output Current IGBT and MOSFET Driver
www.vishay.comthe drive voltages required by gate controlled devices. The voltage and current supplied by this optocoupler makes it ideally suited for directly driving IGBTs with ratings up to 800 V/50 A. For IGBTs with higher ratings, the VO3120 can be used to drive a discrete power stage which drives the IGBT gate. FEATURES • 2.5 A minimum peak output ...